ENFORCER VS-1AHHAQ User manual

VS-1AHHAQ
Manual
HDMI Surge Protector
Helps prevent damage to sensitive HDMI equipment such as
players, monitors, and projectors
Intercepts repeated surges and spikes that could damage
HDMI A/V equipment
Built-in ESD, EFT
Reaction speed <1ns
Passive operation –no external power required
Includes a 12‖ (30cm) grounding wire for convenient connection to
ground

ENFORCER HDMI Surge Protector
2SECO-LARM U.S.A., Inc.
To HDMI
Input
Unprotected
End
1" (26mm)
To HDMI
Output
Protected
End
23/16" (56mm)
Grounding Wire
Attachment Location*
(One on each end)
1" (26mm)
*Note: There is a ‘Grounding Wire Attachment Location’ included on both ends of the HDMI Surge
Protector. Grounding wire can be attached to either of these locations.
Introduction:
The ENFORCER HDMI Surge Protector is a passive device that helps protect sensitive HDMI
equipment from power surges. The device can be deployed in new installations or existing
ones.
The ENFORCER HDMI Surge Protector should be installed between HDMI equipment such as
players, monitors, and projectors to protect against surges that could damage the video
equipment.
NOTE: For the best protection, installing two surge protectors is recommended: one at each
end of the cable.
ESD protection
15kV (ESD), 8kV (Contact)
EFT protection
40A (5/50ns)
Surge protection
5A (8/20ns)
Surge reaction speed
<1ns
Connector
In
HDMI
Out
HDMI
Dimensions
23/16"x1"x1" (56x26x26 mm)
Weight
1.2-oz (35g)
Material
Aluminum
Operating temperature
32°~131°F (0°~55° C)
Specifications:
Overview:
1x
HDMI Surge Protector
2x
Mounting screws
1x
12" (30cm) grounding wire
1x
Manual
2x
Plastic wall anchors
1x
Grounding wire screw
Parts List:

ENFORCER HDMI Surge Protector
SECO-LARM U.S.A., Inc. 3
To ground2(can be attached to either end of surge protector)
HDMI Player
(Not Protected)
HDMI Surge
Protector
HDMI cable1
Protected
End
HDMI Monitor
(Protected)
Unprotected
End
Short
HDMI
cable
(Ground can be attached to either end of surge protectors)
HDMI Monitor
(Protected)
Short
HDMI
cable
HDMI Surge
Protector
HDMI Surge
Protector
HDMI cable1
To ground2
To ground2
HDMI Player
(Protected)
Protected
End
Protected
End
Unprotected End
Short
HDMI
cable
Protecting Multiple Devices:
Installation:
1. Detach the existing HDMI cable1from the device to be protected and attach that cable to the
―Unprotected‖ end of the HDMI Surge Protector.
2. Attach another HDMI cable (not included) between the device to be protected and the
―Protected‖ end of the HDMI Surge Protector. The protected cables should be as short as
possible and should not cross unprotected cables.
3. Connect the ground wire from the HDMI Surge Protector (either end2) to earth ground. The
system should use a single ground point and the protected device should be isolated from
ground.
1. Detach the HDMI cable1from both devices to be protected.
2. Attach an HDMI Surge Protector to each end of the HDMI cable, ensuring that the cable is
connected to the ―Unprotected‖ end of the HDMI Surge Protector.
3. Attach another HDMI cable (not included) between each device to be protected and the
―Protected‖ end of its respective HDMI Surge Protector. For best protection, the protected
cables should be as short as possible and should not cross unprotected cables.
4. Connect the ground wire from each HDMI Surge Protector (either end2) to earth ground. The
system should use a single ground point and the protected device should be isolated from
ground.
Protecting a Single Device:
NOTE: These instructions assume that 2 HDMI devices have already been connected together.
1Note: The maximum length of the HDMI cable will depend on the cable‘s specification and quality.
2Note: There is a ‗Grounding Wire Location‘ included on both ends of the HDMI Surge Protector.
Grounding wire can be attached to either of these locations.

ENFORCER HDMI Surge Protector
4SECO-LARM U.S.A., Inc.
Troubleshooting:
NOTICE:The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the
written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original consumer customer. SECO-LARM‘s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by
or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty
installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than
defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser‘s exclusive remedy, shall be limited to
replacement or repair only, at SECO-LARM‘s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or
consequential personal or property damages of any kind to the purchaser or anyone else.
Video image is weak or faded
Reduce the cable length—max. 16.4ft (5m) for 1080p, 11.5ft
(3.5m) for 4K2K
Replace with a higher-grade HDMI cable
No video image
Double-check that the cables were connected properly
Run a continuity test on all wires in the cable
Make sure source and the display are powered
Make sure that there are no problems with the HDMI source,
HDMI cables, or HDMI display by removing the HDMI surge
protector.
MiVS-1AHHAQ_141215.docx
PITSW4
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: www.seco-larm.com
E-mail: [e-mail]
IMPORTANT:Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws
and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product
in violation of any current laws or statutes.
WARNING:Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock,
damage the device, and void the warranty. Do not open the case of this device, as there are no field-serviceable components inside.
Also Available from SECO-LARM:
Video Surge Protector
VS-1V12BQ
PoE Surge Protector
IPV-P188Q
HD-SDI Surge Protector
VS-1V22AQ
IP Surge Protector
IPV-PD88Q