ENFORCER IPV-P188Q User manual

ENFORCER PoE (Power over Ethernet) Surge Protector
4SECO-LARM U.S.A., Inc.
Also Available from SECO
-
LARM:
Wavy or ghost
video
image if connected to
an image processor (e.g., multiplexer or
DVR), but not if connected directly to the
monitor.
•
Move the cable a ay from possible sources of interference.
•
Replace the cable ith a ne cable.
•
Ensure that the protected cable is as short as possible
Video image background flutters bet een
dark and light.
•
Remove a local po er source, or adjust the monitor’s
brightness and contrast.
Video image is eak or faded.
•
Reduce the cable length.
•
Replace ith a higher-grade cable. Cat5 cable meets the
specifications in the manual. Cat6 cable allo s longer
range.
No video image.
•
Double-check that the cables ere connected properly.
•
Run a continuity test on all ires in the cable.
Troubleshooting:
Video Surge Protector
VS-1V12 Q
IP
Surge Protector
IPV-PD88Q
HD
-
SDI Surge Protector
VS-1V22AQ
MilPV-P188Q_1404.docx
PITSW4
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: .seco
-
larm.com
E-mail: [e-mail]
NOTICE
: The information and specifications printed in this manual are current at the time of publication. Ho ever, the SECO-LARM policy
is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications ithout notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rig
hts reserved. This material may not be reproduced or copied, in hole or in part, ithout the
ritten permission of SECO
-
LARM.
IMPORTANT
: Users and installers of this product are responsible for ensuring this product complies ith all national, state, and local
la s and statutes related to monitoring and recording audio and video signals. SECO-LARM ill not be held responsible for the use of this
product in violation of any current la s or statutes.
WARNING
: Incorrect mounting hich leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock,
damage the device, and void the arranty. Do not open the case of this device, as there are no field-serviceable components inside.
WARRANTY
: This SECO-LARM product is arranted against defects in material and orkmanship hile used in normal service for a
period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating
properly as a result of causes other than defects in material and orkmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any
kind to the purchaser or anyone else.
IPV-P188Q
Manual
•
Helps prevent damage to sensitive net orking equipment
•Intercepts repeated surges and spikes that could damage net ork
equipment
•Installs on a Cat5e/6 4-pair UTP cable ith RJ45 jacks
•Po er and signal line protection
•10/100 Base-T Cat5/5e compatible
•Support mid-span PoE and end-span PoE
•Complies ith 802.3af and 802.3at for PoE
•Includes a 16” grounding ire for convenient connection to ground
PoE (Po er over Ethernet) Surge Pro
tector

ENFORCER PoE (Power over Ethernet)
Surge
2
Band idth
Maximum input
Insertion loss
Return loss
Frequency response
Insulation resistance
Maximum surge voltage
Discharging current
Surge life
Surge protection time
Surge resistance
Signal passing
capability
Breakdo n voltage
Clamping voltage
Po er passing capability
Connector
In
Out
Impedance
Dimensions
Weight
Material
Operating temperature
Introduction:
The ENFORCER PoE (Po er over Ethernet) Surge Protector is a passive device that helps protect
sensitive net orking equipment from po er surges. The device can be deployed in ne
installations or added to existing ones.
The ENFORCER PoE Surge Protector should be installed bet een the PoE hub and a net orked
device to protect against surges that could damage the equipment.
NOTE
: For the best protection, installing t o surge protectors is recommended:
the
net ork cable.
Specifications:
Overview:
P
rotected
End
3½
”
(88mm)
3
”
(75mm)
1”
(25mm)
Mounting Tab
To
Cat5e/6
Cable
Top View
Surge
Protector
SECO-LARM U.S.A., Inc.
Up to 68MHz
58Vp
-
p
<0.2dB
16dB@
100

Up to 3dB@68MHz
10,000
M
Up to 4 kV
400A
30000 surges@4 kV
1ns
0

58V
77V
45W
RJ45
RJ45
4
2
Ω
3½"x1"x1" (88x26x25
mm)
2.8
-
oz
(80g)
Aluminum
-
40°~185° F (
-
40°~85° C)
The ENFORCER PoE (Po er over Ethernet) Surge Protector is a passive device that helps protect
sensitive net orking equipment from po er surges. The device can be deployed in ne
The ENFORCER PoE Surge Protector should be installed bet een the PoE hub and a net orked
device to protect against surges that could damage the equipment.
: For the best protection, installing t o surge protectors is recommended:
one at each end of
Unp
rotected End
1”
(25mm)
1”
(25mm)
Grounding
Wire
ENFORCER
PoE (Power over Ethernet)
SECO-LARM U.S.A., Inc.
1x
P
oE
Surge Protector
2x
Mounting Scre s
1.
Each of the t o
PoE Surge Protector
s
should be mounted as close as possible to the device
be protected.
2. Detach the existing Cat5e/6 cables from the devices to be
protected (su
Camera) and attach them to end of their corresponding
PoE Surge Protector marked “Cable End.”
3. Prepare and connect an additional Cat5e/6 cable to each
device to be protected and to the end of
Surge Protector marked “Equipment End.” For best protection,
possible to connect the PoE Surge Protectors
and the protected device
should not cross unprotected cables.
4. Connect the ground ires from the PoE Surge Protectors
to earth ground.
single ground point and the protected device should be isolated from ground.
Protecting a Single Device:
1.
The PoE Surge Protector should be mounted as close as possible to the device that
2.
Detach the existing Cat5e/6 cable from the device to be protec
Protector marked “Cable End.”
3.
Prepare and connect an additional Cat5e/6 cable to the device
Surge Protector ma
rked “Equipment End.” For best protection, this cable should be the shortest length
possible to connect the PoE Surge Protector and the protected device.
should not cross unprotected cables.
4. Connect the ground ire from the
PoE Surge Protector to earth ground.
ground point and the protected device should be isolated from ground.
Protecting Multiple Devices:
NOTE
: These instructions assume that 2 PoE
devices have already been connected together.
IP Camera
(Protected)
PoE
Surge
Protector
To ground
Shortest Possible
Cat5e/6 cable
Cat5e/6 cable
Protected End Unprotected End
Unprotected End
To ground
PoE Surge
Protector
PoE Surge
Protector
Cat5e/6 cable
Protected End
IP Camera
(Protected)
Shortest
Possible Cat5e/6
cable
Installation:
Parts List:
PoE (Power over Ethernet)
Surge Protector
3
2x
Plastic Wall Anchors
should be mounted as close as possible to the device
s
that
are to
protected (su
ch as a PoE s itch and IP
PoE Surge Protector marked “Cable End.”
device to be protected and to the end of
its
PoE
Surge Protector marked “Equipment End.” For best protection,
these cables
should be the shortest length
and the protected device
s.
In addition the protected cables
to earth ground.
The system should use a
single ground point and the protected device should be isolated from ground.
The PoE Surge Protector should be mounted as close as possible to the device that
is to
be protected.
otected and attach it to end of the PoE Surge
vice to be protected and to the end of the PoE
rked “Equipment End.” For best protection, this cable should be the shortest length
possible to connect the PoE Surge Protector and the protected device.
In addition the protected cables
PoE Surge Protector to earth ground.
The system should use a single
ground point and the protected device should be isolated from ground.
devices have already been connected together.
PoE S itch
(Not Protected)
Cat5e/6 cable
Protected End
Shortest
Possible Cat5e/6
cable
PoE S itch
(Protected)
PoE Surge
Protector