England's Stove Works 18-MH User manual

INSTALLATION & OPERATION MANUAL
Thank you for purchasing this product from a fine line of heating equipment.
We wish you many years of safe heating pleasure.
Visit our web site at www.englanderstoves.com for helpful information,
frequently asked questions, parts & accessory orders and more.
NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO
THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489.
CAUTIONS AND WARNINGS:
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING THIS MODEL.
CAUTION: This stove must be installed in accordance with the Manufactured
Home and Safety Standard (HUD), CFR 3280, Part 24 and must comply
with local building and fire codes. Failure to follow these instructions
could result in property damage, bodily injury or even death. Keep
children, furniture, fixtures and all combustibles away from any
heating appliance.
NOTE: THIS STOVE IS MOBILE HOME AND DOUBLE WIDE APPROVED (WITH
OUTSIDE AIR HOOK-UP). DO NOT INSTALL IN A SLEEPING ROOM. THE
STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL AND
CEILING/ROOF MUST BE MAINTAINED.
England’s Stove Works highly recommends the use of smoke detectors and Carbon
Monoxide detectors with any hearth product, including this unit. Follow all
manufacturer’s instructions when using smoke or Carbon Monoxide detectors.
This product contains a catalytic combustor, which needs periodic inspection and
replacement for proper operation. It is against the law to operate this wood
heater in a manner inconsistent with the operating instructions in this manual, or
if the catalytic element is deactivated or removed.
Our catalytic stoves are designed to burn seasoned, dry wood.
18-MH, 50-SHW15 & 50-TRW15
COMPLIANCE STATUS
TYPEFUEL WOOD
EPA CERTIFICATE NO. 335
EMISSION RATE 1.97 GRAMS/HR
OVERALL TEST EFFICIENCY 80.6%
REV. 2/06

A letter from our Technical Support department:
Thank you for purchasing this fine product from England’s Stove
Works!
England's Stove Works was started, and is still owned by, a family
that believes strongly in a "Do It Yourself" spirit – that’s one reason
you found this product at your favorite “Do It Yourself” store.
We intentionally design and build our stoves so that any homeowner
can maintain his or her unit with basic tools, and we're always more
than happy to show you how to do the job as easily and as
inexpensively as possible.
From our free, downloadable service sheets; to our Pellet Service
Video; to our new "wizard-style," click-through Troubleshooting
guide on our web site, we have always tried to help our customers
stay "heat-ready," especially when oil and electricity prices continue
to skyrocket.
Please look at our vast Help section on our web site and call our
Customer Service department at [phone] if you need any help
with your unit.
We are nearly always able to help “walk you through” any repairs,
problems or questions you may have.
PLEASE NOTE: While information obtained on our web site and
through our 800 number is always free of charge, there will be a
service charge incurred with any “on-site” repairs or maintenance
that we may arrange.
Wishing you years of efficient, quality and “comfy” heating,
England’s Stove Works
Technical Support Department
www.englanderstoves.com
[phone]
IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER.
CONTACT CUSTOMER SERVICE at 1 [phone].

SAFETY NOTICE:
IF THIS WOOD STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE COULD
RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS.
CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS
AND INSTALLATION INSPECTIONS IN YOUR AREA. OUTSIDE AIR MUST BE
PROVIDED WHEN INSTALLING THIS UNIT IN A MOBILE HOME OR DOUBLE
WIDE.
SECTION I: FLUE SYSTEM FOR 18-MH, 50-SHW15 and 50-TRW15
A. Existing Flue System
If you have chosen a freestanding unit, this unit is designed to connect to an
existing flue system, such as masonry or a pre-manufactured Class A flue system. If
you have a masonry system you should inspect the inner liner very carefully for
cracks; if any are there, we recommend you install or have a stainless steel liner
installed. If you have an existing pre-manufactured flue system you should inspect
the inner liner to ensure there is no buckling, warping or cracks in the liner.
Whether your flue system is masonry or pre-manufactured, it should be cleaned
before installing the new unit to the flue system. We strongly recommend you have a
qualified chimney sweep clean and inspect your flue system. The sweep in most
cases will be able to make any necessary repairs or at least recommend qualified
people to do so. It is not permissible to connect your new unit to a flue system
that services another heating appliance.
B. Flue Size Needed
The proper flue size is determined by measuring the inside diameter of the flue
collar on the unit. This unit is equipped with a six inch (6”) TOP EXHAUST FLUE
COLLAR. Therefore, the connector pipe should be six inches (6”) or larger pipe and
never less in diameter than the flue collar on the stove. The area of the chimney liner
must also be equal to or greater than the area of the flue collar on the stove. If the
area of the flue is greater than the area of the collar, it should never be more than
three (3) times greater.
EXAMPLE
The area of a six inch (6”) flue collar is 28.87 square inches; therefore, the
connector pipe should be a six inch (6”) diameter pipe and the chimney liner should
be a minimum of 28.87 square inches, but no greater than 84.8 square inches.
The connector pipe should be 24 gauge steel pipe and eighteen inches (18”) from
a combustible wall or ceiling. If you require closer clearance to combustibles with
your pipe, double wall or shielded pipe is available. This will reduce your clearance to
six inches (6”).

Figure 1 - Installation of 18-MH, 50-SHW15 and 50-TRW15 using Pre-Manufactured Chimney
Note on Outside Air Hookup: You can use an outside air hookup with our catalytic stoves. We highly recommend it
for homes built since the more air-tight construction standards went into effect. This involves connecting a metal
pipe (usually three inches (3”) in diameter - check your stove - and the pipe can be flex or rigid) from the air inlet
p
ipe located on the bottom rear of the stove through your floor or wall. The outside end of this pipe should be
covered in some manner (i.e. with a screen) to keep it clear of foreign matter. It is necessar
y
to use this hookup if
installing in a mobile home or double-wide.
Figure 2 - Installation of 18-MH, 50-SHW15 and 50-TRW15 using Masonry Chimney

C. Installation of a New Flue System
1. Masonry Flue: In the event that you plan to install a flue system or have a flue
system installed, there are several avenues you can take. In the middle and late
Seventies masonry flue systems became very popular, and are satisfactory
systems to have today. If you are considering a masonry system, you should
consult your local building officials for the proper procedures in construction of this
type flue system. We recommend you consult with and have your flue built by a
licensed, bonded contractor.
Most masonry flues are placed against the outside wall and extend upward
above the roof. The flue thimble is then inserted through the wall, making the
connection with the vertical flue and the stovepipe. Exercise extreme caution when
drilling through the wall; you must maintain the proper clearance between the
connecting liner and any combustibles in the wall.
We also recommend that you have a flue door located at least two feet (2’)
below your flue thimble connection for easy access and clean-out. You should
make this door as airtight as possible. It is the responsibility of the consumer to
ensure the chimney or flue system is in good operating condition. The
manufacturer will not be responsible for an accident attributed to a unit
connected to a faulty chimney or flue system.
2. Pre- Manufactured Flue System: In the past few years pre-manufactured flue
systems have become very popular because this type system is fairly easy to install
and, when installed correctly, is very safe. There are many pre-manufactured flue
systems on the market from which to choose. In making your choice be sure the
system you choose has a recognized label such as U.L., B.O.C.A. or I.C.B.O. Any
of these labels will ensure the flue system is constructed of the proper materials
and meets the required safety standards. Your Englander dealer will usually handle
a top grade and approved flue system.
There are two very popular methods for installation of a pre-manufactured flue
system. The most popular and least expensive is through the ceiling and out the
roof. This is the least expensive and creates a tremendous draw because less pipe
is required. It is less expensive because insulated pipe is only needed from the
ceiling up; single wall 24 gauge pipe is used from the unit to the ceiling. The
second method of installation is to go through the wall and up on the outside of the
house or structure. This method is more expensive because more insulated pipe is
required; you must use insulated pipe through the wall and up the outside of your
house. If you choose to go through the ceiling or through the wall, you must
exercise extreme caution in your installation. The proper clearances must be
maintained with either installation. Your flue pipe manufacturer furnishes a wall
thimble or ceiling box, and when these are installed properly the correct safety
clearances will be met. If you choose this type system and are not qualified to
install it, you can contact your local dealer for a qualified contractor. It is the
responsibility of the consumer to ensure the chimney or flue system is in good
operating condition. The manufacturer will not be responsible for an accident
attributed to a unit connected to a faulty chimney or flue system.
*IMPROPER INSTALLATION: The manufacturer will not be held responsible for damage
caused by the malfunction of a stove due to improper venting or installation.
Call
(
800-245-6489
)
and/or consult a
p
rofessional installer if
y
ou have an
y
q
uestions.

SECTION II: FLOOR & WALL PROTECTION
A. Floor Protection
If your floor is constructed of a noncombustible material such as brick or concrete,
no floor protection is required. If your floor is constructed of a combustible material
such as hardwood, carpet or linoleum, you must place floor protection between the
unit and the combustible material.
There are many stove floor and wallboards on the market. You must be very
cautious in choosing the proper protection. The board must be U.L. listed. After
examining the area in which you plan to place your new unit and determining it
requires protection, the next step is to select the proper size board. The unit you
choose will determine the size board that is required. The approved board should be
large enough to provide a minimum of eight inches (8”) behind the unit, eight inches
(8”) on each side of the unit and sixteen inches (16”) in the front of it. This stove
requires a minimum 36” x 48” floor protector.
B. Wall Protection
Your stove can be placed within thirty inches (30”) of a combustible wall such as
paneling, wallpaper or drywall. In some areas local code may call for thirty-six inches
(36”) clearance from a combustible, therefore you should check to see which applies
to your area. If you need to place your unit closer it will require wall protection. There
are many wall board manufacturers, and most require a one inch (1”) air space
between the wall and the board. You can place your unit within twelve inches (12”)
of some boards and reduce your clearance by two-thirds. In addition, the wallboard
only needs to be six inches (6”) higher than the top of the stove; by placing the unit
twelve inches (12”) from a combustible, the flue pipe will be closer than eighteen
inches (18”) from a combustible surface. This will require you to use double wall or
shielded pipe that allows you to come within six inches (6”) of a combustible surface.
Regardless of clearances, we recommend using some type wall protection when
installing this unit in a mobile home or double wide. Always follow the pipe and
board manufacturer’s directions, and contact us if you have any questions.
C. Heat Shield
This stove has a standard heat shield that allows six inches (6”) clearance from
combustibles across the entire rear of the stove. You will still need thirty inches (30”)
clearance from combustibles on each side of the stove.

SECTION lll: FREESTANDING PLACEMENT AND INSTALLATION
Once you have your flue system complete and have installed the floor and wall
protection, you are ready to place your unit. The first problem you may encounter is
getting the stove into your home; all of our products are well constructed, which makes
them rather heavy. To lighten the stove you can remove the door and firebrick. Be sure
to make a note of your unit’s brick placement before you remove your bricks.
After the unit is in place the firebrick and door can be replaced. We recommend you
use a handcart and never try handling one of our units without some help. As a rule,
three or four adults can handle most of our products.
A. Chimney Connector
The chimney connector must be 24 gauge steel pipe and six inches (6”) in
diameter. Do not use aluminum or galvanized pipe for installation of this unit, as this
type pipe will not be able to withstand the extreme temperatures a wood stove will
generate. Do not use chimney connector pipe (single wall) as a chimney. You must
connect your stove to a chimney comparable to those listed previously in this manual
(See Section l).
A chimney connector must be attached to the stove (and to each other) with the
crimped end toward the stove. This allows any creosote to run back inside the pipe
and not down the outside of the pipe. As a safety precaution, all joints should be
sealed with high temperature silicone (AC-RTV3) and secured with three sheet metal
screws, since the pipe could vibrate apart in the event of a creosote fire.
For proper operation, the chimney connector should be as short as possible.
Horizontal runs of chimney connector pipe should have an upward slope from the
stove of one-quarter inch (1/4") per foot. Maintain eighteen inches (18”) of clearance
between the chimney connector and the wall and ceiling unless a wall protection
system is installed. When installing this stove in a mobile home or double wide you
must use double wall or shielded pipe that will allow six inches (6”) clearance from a
combustible.
B. Outside Air Connection
When installing this model in a mobile home or double wide it is necessary to
supply the combustion air into the unit from outside the dwelling. This can be done
by running a thin gauge three inch (3”) pipe (flex or rigid) from the air inlet pipe
located on the rear of the stove through the floor or wall. The outside end of this pipe
should be covered in some manner to keep it clear of foreign matter. If you are
installing this stove in a regular dwelling this connection is not necessary, but is
recommended in air-tight homes.

SECTION IV: ACCESSORY ITEMS
There are several accessory items available for your wood stove. It is suggested you
install any accessory items before reading the next section; if you do purchase
accessories after burning the stove, simply let the unit cool down and add the
accessories as follows:
AC-101-P & SH-101-P Brass Lip Trim
There are two (2) pieces of J-Channel Trim in this kit that snap onto the edges of the
stove. They cover the top front edge, the two vertical front edges and the ash apron front
edge. To remove the protective plastic film, start at one end of the piece and peel off the
film. The pieces are precut -- simply match the piece with the proper edge. After
centering the channel on the edge with the short side of the channel down, force the
underside of the J-Channel over the edge of the metal. If the J-Channel is too tight, get it
started by hand then lightly tap into place with a wooden block or a rubber hammer. If
the J-Channel is too loose and will not stay in place, lay the piece on a flat surface and
bend the short side in on each end and slightly in the middle. Follow this procedure with
each piece.
AC-106-P & SH-106-P Brass Window Trim
With the door closed, take the spring clip that has a tee on one end and twist it into
the groove on the rear side of the window trim. You can place the spring clip on any side
of the trim; however, the side of the trim toward the bottom of the door is best. Hold the
spring clip in place and slide the bottom edge of the trim into the bottom ledge of the
window opening. Press down and in with both hands, pushing the brass trim into
position, then press in on all corners to ensure they are in the window opening as far as
they will go. It is acceptable to use furnace cement on the rear side of the brass trim to
help hold it in place.
AC-02 Brass Rail
This accessory is pre-mounted on a metal base and simply sits on top of the stove.
You may order parts and options on our web site: www.englanderstoves.com
or by calling [phone]

SECTION V: OPERATING INSTRUCTIONS
A. Building a Fire
Your stove is equipped with a catalytic combustor that requires the following
procedure for firing the unit from a cold start. Inspect your stove to be sure the
combustor is well-seated in the combustor housing before starting this procedure.
CAUTION:NEVER LIGHT YOUR FIRE WITH KEROSENE, GASOLINE OR
CHARCOAL LIGHTER FLUID. THIS COULD BE VERY DANGEROUS.
NOTICE: Your new stove and the connector pipe may smoke for a period of time.
This is called “cooking out” and is no cause for alarm. It is a good idea to
open all doors and windows in your dwelling during the first two hours of
operating a new unit.
1. Be sure there are no combustible materials in the immediate area.
2. Pull out completely the slide damper control (located under the ash lip) and the
by-pass damper located on the top right side of the stove.
3. Place several wads of crushed newspaper over the entire bottom of the firebox.
4. Lay small dry sticks of kindling on the top of the paper.
5. Ignite the paper. Leave the door cracked until the kindling is burning freely.
6. Once the kindling is burning well place several pieces of dry split wood on the fire
and allow the wood to burn freely before closing the door completely.
7. Close the door and allow the fire to burn thirty (30) minutes to one hour.
8. Once you have established a hot bed of coals, open the by-pass damper, add
more wood (fill the unit), close the door and allow the wood to burn another thirty
(30) minutes. The final step is to close the by-pass damper and place the slide
damper at your desired setting. Note: Pulling the slide damper out or towards you
increases the amount of combustion air and allows a faster burn. Pushing the rod
in or away from you slows down the amount of air and allows the stove to burn
slower.
NOTE: It is very important the above procedure be followed to ensure the catalytic
combustor reaches the proper temperature. It is recommended the combustor
be operated at 700 to1400 degrees Fahrenheit; the combustor itself has to be
above 500 degrees Fahrenheit before it will accept the smoke. Operating the
unit above 1800 degrees Fahrenheit will damage the combustor, although
temperatures between 1400 and 1600 degrees are common. If minor build-up is
evident on the combustor, run the stove at a high rate with the by-pass damper
partially open to help clean the combustor.
A one-quarter inch (1/4”) button plug is located on the top left side of the unit.
This plug can be removed and a Condor probe thermometer (PART # AC-13)
inserted, which will display the actual temperature of the combustor. This part
can be ordered from the factory or through your local stove dealer.

B. Draft Control
This unit has a slide draft control located under the ash apron, which is used to
regulate the amount of combustion air entering the firebox. This controls the amount
of heat your stove produces, as well as the burn time. The more you open the draft
by pulling out the handle, the more combustion air enters the firebox; this will cause
the stove to burn hotter and faster. You will have to experiment with your unit for the
most efficient setting, as no two systems are the same. If you have any problems
regulating the unit please contact your local dealer or call the factory.
C. Do Not Over-Fire Your Unit
Burning flammable liquids, too much wood and trash in the stove can result in
over-firing. If the chimney pipe turns red or even worse, white, the unit has been
over-fired. This condition may ignite creosote in the chimney and possibly cause a
house fire. If this does happen, immediately close the slide damper by pushing it in
completely and also close the by-pass damper. Get out of the house and call the fire
department. A chimney fire may cause structural damage to the chimney system,
therefore do not use the stove again until the flue system is inspected and, if
necessary, repaired or replaced. A chimney sweep can perform this inspection.
D. Everyday Fueling
Always open or pull out the by-pass damper before opening the door of the stove.
The door should be cracked for five to ten minutes to allow the excess smoke to
clear through your flue system. Never open the door with the by-pass damper
closed.
This stove is designed to burn six to eight hours on one load of seasoned
firewood. Once you have opened the door properly, you should have a bed of hot
coals in the bottom of the firebox. With the use of a poker, pull the bed of hot ashes
towards the door or front of the unit. Now you can fill the stove with seasoned wood,
close the door and allow the unit to burn freely for approximately thirty (30) minutes.
The final step is to close the by-pass damper and set your draft control to your
desired burn. Follow this procedure each time you fuel your stove.
E. Ash Removal and Disposal
Regularly inspect the ash build-up in your stove and remove as necessary.
Ashes should be placed in a metal container with an airtight lid. Pending final
disposal, the ashes should be placed on a non-combustible surface, completely
away from all combustible materials. The ashes should be retained in the closed
container until all cinders have thoroughly cooled. If you have a masonry chimney or
a pre-manufactured chimney system, it is essential that your flue be checked for
creosote build-up at least twice per month.

SECTION VI: CARE AND MAINTENANCE
A. Catalytic Maintenance
Note – Your unit will have a 3” thick, 25-cell combustor (manufactured by Applied Ceramics),
or it will have a 1” thick, “ceramic foam” type combustor (manufactured by Clear
Skies). The following instructions apply to both types, unless otherwise specified.
1. To reach the combustor, first take out the flame impingement plate by removing
the four (4) 3/8” brass nuts (they take a 9/16” wrench). Once the nuts are
removed the plate should drop from the four bolts. This will allow you to see the
bottom of your catalytic combustor.
2. For 25-cell Applied Ceramics combustor: If the combustor is plugged up you will
see black soot within the cells on the bottom side of the ceramic piece. This can
usually be removed by brushing the combustor with a soft bristled brush. You
can also run a pipe stem cleaner through each cell for removal of any internal
build-up. This type cleaning can be done without removing the combustor from
the stove.
3. For 1” thick Clear Skies combustor: Follow the instructions provided by Clear
Skies pertaining to the cleaning of their combustor.
4. The flame impingement plate (Part #IP-18PC) is held in the unit as described
previously. This can be cleaned with a stiff bristled brush.
5. The combustor collar (Part #CA-1710) is also held in place by four (4) 3/8” brass
nuts (they take a 9/16” wrench). The flame impingement plate must be removed
before the combustor collar. Once the second set of nuts is removed the collar
will come out with the catalytic combustor seated in it. Reverse this procedure to
replace the collar and flame impingement plate.
6. The catalytic combustor (Part #AC-6C3) is guaranteed by the manufacturers. A
separate warranty card will be in the manual for this part and should be mailed
back to the combustor manufacturer. Both combustors are equivalent, and in the
event there is a problem with this item, Customer Service should be contacted at
1-800-245-6489.
B. Gaskets
Each unit comes with a gasket around the door, which should be replaced every
two years. To replace the door gasket (Part # AC-DGKC), the old gasket should first
be removed entirely. This may require you to scrape the old gasket and cement from
the channel before adding new cement and 3/4” rope gasket. After attaching the new
gasket, close the door and allow 24 hours for the cement to harden.
If you are replacing the window gasket (Part #AC-GGK), the gasket already has
adhesive on one side. Remove the paper on the adhesive side and place the gasket
around the outside edge of the glass. The easiest way to do this is to form a “U” with
the gasket and place this around the outer perimeter of the glass.
The door gasket as well as the window gasket can be ordered from your local
dealer or from our factory.

C. Firebrick (Part #AC-SB; 20 Required)
This stove is equipped with high density, high temperature firebrick. If the brick
becomes chipped or cracked, especially on the sides of the firebox, it should be
replaced. The brick can be ordered from your local dealer or from the factory.
D. Finish (Part #AC-MCSP; 12 oz. Spray Can)
Your stove has been painted with 1200 degree Metallic Charcoal paint that will
retain its original appearance for years. However, if your stove should get wet, some
rust spots may appear. These can be removed with plain steel wool and touched up
with new paint. If you need to repaint the unit, use our paint as other brands may not
be able to withstand the high surface temperatures. This spray paint can be ordered
from your local dealer or from the factory.
SECTION VII: CHIMNEY AND FLUE PIPE MAINTENANCE
A. Chimney System
Many stove owners prefer to clean their own chimneys; however, we highly
recommend a chimney sweep be contacted to do this job. A professional sweep can
clean and inspect your system and in some cases spot problems that you may
overlook.
B. Flue Pipe Maintenance
When connecting your unit to the flue system, 24 gauge or thicker pipe should be
used. Your pipe should be cleaned at least once a year and inspected monthly. Most
people will clean their pipe and stove at the end of the heating season as this will
keep odors from entering the house during the summer months. The flue pipe should
be replaced every three to five years, depending on the thickness of the pipe (thicker
pipe will last longer).

SECTION VIlI: THINGS THAT COULD CAUSE YOUR STOVE TO SMOKE
It is very important that installations are made airtight. This is best accomplished
by using furnace cement at all pipe joints and where the first section of pipe enters
the stove and enters the chimney flue. Any existing air leaks will cause the air to
draw at points where the least resistance is offered — such places are pipe joints,
flue thimble, flue openings in the chimney, ash clean-out doors and cracks in the
chimney. These areas may cause air to enter your system and not be drawn through
the stove as necessary, which could result in a cool chimney, causing the smoke to
build up in the system and eventually come back into the house. This is called “back
puffing” and can be helped by sealing all troublesome areas so they are airtight.
There are two main causes of chimney down drafts. One is from the air currents
being deflected down the chimney by nearby objects such as trees, a building or a
hill. The other cause is that in many chimneys the flue gases chill too quickly as they
pass up the chimney system. When the flue gas cools too quickly, it becomes heavy
and will back up in the system; this will often result in “back puffing,” poor combustion
and smoke odors in the house. Burning the stove hotter will, in some cases, help this
situation. If you have any problem with “back puffing” or a poor drawing chimney
system, contact your local dealer or call the factory.
SECTION IX: WHAT CAUSES CREOSOTE?
Creosote is caused by the condensation of the vapor that exists in the escaping
smoke; the moisture level of your fuel will determine the density of this vapor. A
severe downdraft as discussed previously will also cause creosote. Moisture will
form at the coolest point in your chimney system and at this point will tend to build
creosote. The ash is picked up by the moisture in the system and will build up or run
back down the inside of your flue.
This situation can sometimes be helped by installing an “open vented” type
chimney cap, which will allow the chimney to maintain more heat to create a better
draw and keep some wind currents from entering the system. This type cap will not
correct a poorly constructed chimney or one in need of repair. Such chimneys may
have to be relined or rebuilt.

REPLACEMENT PARTS FOR 18-MH, 50-SHW15 and 50-TRW15
AC-DGKC DOOR GASKET KIT
AC-FCGK FLUE COLLAR GASKET KIT
AC-SB 9” X 4” X 1 ½” FIREBRICK (20)
AC-G9 9” X 9” GLASS W/GASKET
AC-SH DOOR SPRING HANDLE
AC-SH4 SLIDE DRAFT SPRING HANDLE
AC-SHM BY-PASS SPRING HANDLE
AC-6C3 CATALYTIC COMBUSTOR
AC-MCSP HI-TEMP METALLIC PAINT
CA-1710 COMBUSTOR HOUSING
CA-20 6” FLUE COLLAR
IP-18PC FLAME IMPINGEMENT PLATE
NOTE: Accessory items and trim (found in Section IV of this manual) may
also be ordered.
NOTE: ALL PARTS CAN BE ORDERED FROM YOUR LOCAL DEALER,
FROM OUR FACTORY, OR FROM OUR WEB SITE.
www.englanderstoves.com
If you have any questions or problems contact our
Customer Service Department at 1-800-245-6489.
CUSTOMER SERVICE DEPARTMENT Tech. Questions (800-245-6489)
P.O. BOX 206 (FAX [phone])
MONROE, VA 24574 Parts Orders ONLY (800-516-3636)

Have this information on hand if you phone the factory or your dealer regarding this product.
Retain for your files:
Model Number __________________________
Date of Purchase ________________________
Date of Manufacture _________________ Serial #_____________________
LIMITED 5 YEAR WARRANTY FROM THE DATE OF
PURCHASE TO THE ORIGINAL OWNER
The manufacturer extends the following warranties:
Five Year Period:
1. Carbon steel and welded seams in the firebox are covered for 5 years against splitting.
2. The cast iron door, hasp and hinges are covered for 5 years against cracking.
One Year Period:
3. Component parts such as combustor housing, flue collar, flame impingement plate, baffle
plate, brick retainers, combustor plate and fasteners are covered for 1 year against cracking,
breakage and welded seams from separating.
4. Electrical components, accessory items, glass and the painted surface are covered for 1 year
from the date of purchase.
Conditions and Exclusions:
Damage from over-firing will void your warranty.
This warranty does not apply if damage occurs because of an accident, improper handling,
improper operation, improper installation, abuse, or unauthorized repair made or attempted to be
made.
The manufacturer is not liable for indirect, incidental, or consequential damages in connection
with the product including any cost or expense providing substitute equipment or service during
periods of malfunction or nonuse.
All liability for any consequential damage for breach of any written or implied warranty is
disclaimed and excluded. Some states do not allow the exclusion or limitations of incidental or
consequential damages, so the above may not apply to you.
Procedure:
Purchaser must give notice of claim of defect within the warranty period and pay transportation to
and from a service center designated by the factory. The dealer from which the unit was
purchased or the factory, at our option, will perform the warranty service.
Other Rights:
This warranty gives you specific legal rights, and you may also have other rights, which may vary
from state to state.
NOTE:THIS WARRANTY IS NULL AND VOID IF YOU DO NOT RETURN
THE ATTACHED WARRANTY REGISTRATION WITH A COPY OF THE SALES
RECEIPT WITHIN 30 DAYS FROM THE DATE OF PURCHASE.
WARRANTY IS NOT TRANSFERABLE.

WARRANTY REGISTRATION for England’s Stove Works
Purchased by (Name) ______________________________________________
Address _________________________________________________________
City ________________________ State __________ Zip _________________
Telephone _______________________________________________________
Email Address ___________________________________________________
DEALER INFORMATION
Purchased From (Dealer) ___________________________________________
Address _________________________________________________________
City ________________________ State __________ Zip _________________
UNIT INFORMATION
(Please be sure to refer to sticker on back of manual or box to complete this section)
Model Number _____________________ Purchase Date _________________
Purchase Price ____________________
Serial Number _____________________ Mfg. Date ______________________
How did you first hear about our product? (please check one)
___ Word of Mouth ___ Burn Trailer Demonstration ___ Internet
Other: ____________________________________________________
Where did you receive information about our product? (please check one)
___ Rec’d. info. via phone ___ Dealer (Name of dealer): _____________________
___ Internet Other: _________________________________________________
IMPORTANT NOTICE
THIS REGISTRATION INFORMATION MUST BE ON FILE FOR THIS WARRANTY TO BE VALID.
PLEASE MAIL THIS INFORMATION WITHIN THIRTY (30) DAYS FROM THE DATE OF PURCHASE.
Mail To:
England’s Stove Works, Inc.
Customer Service Department
P.O. Box 206
Monroe, VA 24574
Or, Fax To:
[phone] – 24 hours a day
Or, now available – Go online to complete your Warranty Registration!
Visit www.englanderstoves.com if you prefer to register online.