Entrematic Ditec NES300EH User manual

Ditec NeoS / NeoS+
Sliding Gates
(Original instructions)
www.entrematic.com
IP2160EN
Technical Manual

28
IP2160EN - 2017-04-12
Contents
Key
Subject Page
1. General safety precautions 29
General safety precautions for the user 30
2. Declaration of incorporation of partly completed machinery 31
2.1 Machinery Directive 31
3. Technical specifications 32
3.1 Operating instructions 33
4. Standard installation 34
5. Dimensions 35
6. Main components 35
7. Installation 36
7.1 Preliminary checks 36
7.2 Base plate position 37
7.3 Gearmotor installation 38
7.4 Rack installation 39
7.5 Operation with encoder 40
7.6 Magnetic limit switch installation and adjustment 40
7.7 Chain drive kit installation 41
8. Electrical connections 43
8.1 Installation of internal photocell 44
9. Routine maintenance plan 44
Operating instructions 45
i
This symbol indicates instructions or notes regarding safety, to which special atten-
tion must be paid.
This symbol indicates useful information for the correct functioning of the product.
All the rights concerning this material are the exclusive property of Entrematic Group AB.
Although the contents of this publication have been drawn up with the greatest care, Entrematic Group AB
cannot be held responsible in any way for any damage caused by mistakes or omissions in this publication.
We reserve the right to make changes without prior notice.
Copying, scanning and changing in any way are expressly forbidden unless authorised in writing by Entrematic
Group AB.

29
IP2160EN - 2017-04-12
1. General safety precautions
This installation manual is intended for qualified personnel only.
Installation, electrical connections and adjustments must be performed by qualified person-
nel, in accordance with Good Working Methods and in compliance with the current regulations.
Read the instructions carefully before installing the product.
Bad installation could be dangerous.
The packaging materials (plastic, polystyrene, etc.) should not be discarded in the environ-
ment or left within reach of children, as they are a potential source of danger.
Before installing the product, make sure it is in perfect condition.
Do not install the product in explosive areas and atmospheres: the presence of inflammable
gas or fumes represents a serious safety hazard.
Before installing the motorisation device, make all the necessary structural modifications to
create safety clearance and to guard or isolate all the crushing, shearing, trapping and general
hazardous areas.
Make sure the existing structure is up to standard in terms of strength and stability. The mo-
torisation device manufacturer is not responsible for failure to observe Good Working Methods
when building the frames to be motorised, or for any deformation during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking into
account: applicable laws and directives, Good Working Methods, installation premises, system
operating logic and the forces developed by the motorised door or gate.
The safety devices must protect against crushing, cutting, trapping and general danger areas
of the motorised door or gate.
Display the signs required by law to identify hazardous areas.
Each installation must bear a visible indication of the data identifying the motorised door
or gate.
When necessary, connect the motorised door or gate to an effective earthing system that com-
plies with the current safety standards.
During installation, maintenance and repair operations, cut off the power supply before
opening the cover to access the electrical parts.
The automation protection casing must be removed by qualified personnel only.
The electronic parts must be handled using earthed antistatic conductive arms. The manufac-
turer of the motorisation declines all responsibility if component parts not compatible with safe
and correct operation are fitted.
Only use original spare parts for repairing or replacing products.
The installer must supply all information concerning the automatic, manual and emergency op-
eration of the motorised door or gate, and must provide the user with the operating instructions.
Failure to respect the information given in this manual
may cause personal injury or damage to the device.
Keep these instructions for future reference

30
IP2160EN - 2017-04-12
These precautions are an integral and essential part of the product
and must be supplied to the user.
Read them carefully since they contain important information on safe
installation, use and maintenance.
These instructions must be kept and forwarded to all possible future
users of the system.
This product must only be used for the specific purpose for which it
was designed.
Any other use is to be considered improper and therefore dangerous.
The manufacturer cannot be held responsible for any damage caused
by improper, incorrect or unreasonable use.
Avoid operating in the proximity of the hinges or moving mechanical
parts. Do not enter within the operating range of the motorised door
or gate while it is moving.
Do not obstruct the motion of the motorised door or gate, as this may
cause a dangerous situation.
The motorised door or gate may be used by children over the age of 8
and by people with reduced physical, sensorial or mental abilities, or
lack of experience or knowledge, as long as they are properly supervised
or have been instructed in the safe use of the device and the relative
hazards.
Children must be supervised to make sure they do not play with the
device, nor play/remain in the sphere of action of the motorised door
or gate.
Keep remote controls and/or any other command devices out of the
reach of children, to avoid any accidental activation of the motorised
door or gate.
In the event of a product fault or malfunction, turn off the power supply
switch. Do not attempt to repair or intervene directly, and contact only
qualified personnel.
Failure to comply with the above may cause a dangerous situation.
Any repair or technical intervention must be carried out by qualified
personnel.
Cleaning and maintenance work must not be carried out by children
unless they are supervised.
To ensure that the system works efficiently and correctly, the manufac-
turer’s indications must be complied with and only qualified personnel
must perform routine maintenance on the motorised door or gate. In
particular, regular checks are recommended in order to verify that the
safety devices are operating correctly.
All installation, maintenance and repair work must be documented and
General safety precautions for the user

31
IP2160EN - 2017-04-12
2. Declaration of incorporation of partly com-
pleted machinery
2.1 Machinery Directive
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB, with headquarters in Lodjursgatan 10, SE-261 44 Land-
skrona, Sweden, declares that the automation for Ditec sliding gates NES300EH, NES300EHP,
NES400EH, NES400EHP, NES600EH, NES600EHP, NES1000EHP:
- is designed to be installed on a manual gate to form a machine pursuant to Directive 2006/42/
EC. The manufacturer of the motorised gate must declare conformity with Directive 2006/42/
EC (annex II-A) prior to initial machine start-up;
- conforms to the applicable essential safety requirements indicated in ANNEX I, Chapter 1 of the
Directive 2006/42/EC;
- conforms to the Low Voltage Directive 2006/95/EC;
- conforms to the Electromagnetic Compatibility Directive 2004/108/EC:
- conforms to the R&TTE Directive 1999/5/EC;
- the technical documentation conforms to Annex VII-B of the Directive 2006/42/EC;
- the technical documentation is managed by Marco Pietro Zini with headquarters in Via Mons.
Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY;
- a copy of technical documentation will be provided to national competent authorities, following
a suitably justified request.
Landskrona, 01-07-2014 Matteo Fino
(Chairman)
Pursuant to Machinery Directive (2006/42/EC) the installer who motorises a door or gate has the
same obligations as the manufacturer of machinery and as such must:
- prepare the technical data sheet which must contain the documents indicated in Annex V of the
Machinery Directive;
(The technical data sheet must be kept and placed at the disposal of competent national authori-
ties for at least ten years from the date of manufacture of the motorised door);
- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery Direc-
tive and deliver it to the customer;
- affix the EC marking on the motorised door or gate, in accordance with point 1.7.3 of Annex I of
the Machinery Directive;
- ensure compliance of the motorised door or gate with safety regulations, by installing the neces-
sary safety devices;
- carry out the safety test , modifying parameters and (if used) from the menu;
- refer to the installation manual of the CS12E - CS12M control panel for the operating force
adjustments, in compliance with EN12453 and EN12445.
made available to the user.
Only lock and release the door wings when the motor is switched off.
Do not enter within the operating range of the wing.
To dispose of electrical and electronic equipment correctly, users
must take the product to special "recycling centres" provided by
the municipal authorities.
(
Cha
Ch
Ch
Ch
Ch
Ch
C
C
C
h
Ch
Ch
Ch
C
C
C
h
Ch
h
h
C
C
C
C
Ch
Ch
h
Ch
Ch
C
C
Ch
Ch
h
h
C
C
Ch
Ch
Ch
C
Ch
C
C
h
Ch
C
C
C
C
h
C
C
h
h
C
Ch
C
Ch
C
C
C
C
Ch
h
C
h
h
C
C
C
h
h
C
h
h
C
C
C
C
h
h
C
irm
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
an)
an

32
IP2160EN - 2017-04-12
3. Technical specifications
Ditec NES300EH Ditec NES300EHP
Power supply 230 V~ 50/60Hz 230 V~ 50/60Hz
Absorption 1,2 A 1,2 A
Fuse F1,6A F1,6A
Thrust 300 N 300 N
Wing speed 0,1÷0,25 m/s 0,1÷0,25 m/s
Max stroke 12 m 12 m
Max wing weight 300 kg 300 kg
Service class 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min - S3 = 50% S2 = 30 min - S3 = 50%
Ambient
temperature -20° C +55° C -20° C +55° C
Degree of protection IP24 IP24
Control panel CS12E CS12M
Ditec NES400EH Ditec NES400EHP Ditec NES400EHJ
Power supply 230 V~ 50/60Hz 230 V~ 50/60Hz 120 V~ 50/60Hz
Absorption 1,2 A 1,2 A 2,4 A
Fuse F2A F2A F4A
Thrust 400 N 400 N 400 N
Wing speed 0,1÷0,25 m/s 0,1÷0,25 m/s 0,1÷0,25 m/s
Max stroke 12 m 12 m 12 m
Max wing weight 400 kg 400 kg 400 kg
Service class 4 - INTENSE 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min - S3 = 50% S2 = 30 min - S3 = 50% S2 = 30 min - S3 = 50%
Ambient
temperature -20° C +55° C -20° C +55° C -20° C +55° C
Degree of protection IP24 IP24 IP24
Control panel CS12E CS12M CS12E
Ditec NES600EH Ditec NES600EHP Ditec NES600EHJ
Power supply 230 V~ 50/60Hz 230 V~ 50/60Hz 120 V~ 50/60Hz
Absorption 1,5 A 1,5 A 3 A
Fuse F2A F2A F4A
Thrust 600 N 600 N 600 N
Wing speed 0,1÷0,24 m/s 0,1÷0,24 m/s 0,1÷0,24 m/s
Max stroke 20 m 20 m 20 m
Max wing weight 600 kg 600 kg 600 kg
Service class 4 - INTENSE 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
Ambient
temperature -20° C +55° C -20° C +55° C -20° C +55° C
Degree of protection IP24 IP24 IP24
Control panel CS12E CS12M CS12E

33
IP2160EN - 2017-04-12
3.1 Operating instructions
Service class: 4 (minimum 10-5 years of working life with 100-200 cycles per day).
Applications: INTENSE (for apartment block, industrial and commercial entrances and car parks
with vehicle access or access for intense pedestrian use).
- Performance characteristics are to be understood as referring to the recommended weight (ap-
prox. 2/3 of maximum permissible weight). When used with the maximum permissible weight
a reduction in the above mentioned performance can be expected.
- Service class, running times, and the number of consecutive cycles are to be taken as merely
indicative, having been statistically determined under average operating conditions, and are
therefore not necessarily applicable to specific conditions of use.
- Each automatic entrance has variable elements such as: friction, balancing and environmental
factors, all of which may substantially alter the performance characteristics of the automatic
entrance or curtail its working life or parts thereof (including the automatic devices themselves).
The installer should adopt suitable safety conditions for each particular installation.
Ditec NES1000EHP Ditec NES1000EHPJ
Power supply 230 V~ 50/60Hz 120 V~ 50/60Hz
Absorption 2 A 4 A
Fuse F2,5 A F6,3A
Thrust 1000 N 1000 N
Wing speed 0,1÷0,19 m/s 0,1÷0,19 m/s
Max stroke 20 m 20 m
Max wing weight 1000 kg 1000 kg
Service class 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
Ambient
temperature -20° C +55° C -20° C +55° C
Degree of protection IP24 IP24
Control panel CS12M CS12M

34
IP2160EN - 2017-04-12
4. Standard installation
Ref. Code Description
1 NES300
NES400
NES600
NES1000
300 kg gearmotor with control panel
400 kg gearmotor with control panel
600 kg gearmotor with control panel
1000 kg gearmotor with control panel
2 ZEN2 / ZEN4
ZEN2C / ZEN4C
Remote control
3 FL24 Flashing light
4 XEL5
LAN4
GOL4M
Key selector switch
Keypad
Wireless keypad
5 LIN2
XEL2
LAB4
Photocells
IP55 photocells
6 SOFA-SOFB
GOPAV
Safety edge
Radio system for safety edges
7 LAB9 Magnetic loop detector for passage control
AConnect the power supply to a type-approved omnipolar switch, with a contact opening distance of at
least 3 mm (not supplied).
The connections to the mains and low voltage wires (230V) must be made on an independent channel
separated from the connections to the command and safety devices (SELV = Safety Extra Low Voltage).
1 A
4
7
2
6
3
5
5

35
IP2160EN - 2017-04-12
5. Dimensions
335
307 (NES 300-400)
325 (NES 600-1000)
90
210 (NES 300-400)
220 (NES 600-1000)
170 (NES 300-400)
180 (NES 600-1000)
40
6. Main components
Ref. Code Description
8Motor
9Control panel
10 Diagnostic circuit
11 Key release
12 Pinion
13 Battery kit
14 Cable inlet
15 Power supply terminal
8
11 10
9 8 13
91514
12

36
IP2160EN - 2017-04-12
7.1 Preliminary checks
Check the stability of the wing (derailing and lateral falls) and the sliding wheels and that the upper
guides do not cause any friction.
The sliding guide must be securely fixed to the ground for the full length within doorway and must
have no irregularities that could hinder the movement of the wing.
The opening and closing stops must be fitted.
If the gate has slits, make sure they are covered to prevent shearing points or install active safety
edges on the columns.
Safety device should be installed at the end of the wing to reduce the collision force.
NB: make sure that the gate can not exit the sliding guides and fall.
7. Installation
The given operating and performance features can only be guaranteed with the use of DITEC ac-
cessories and safety devices.
Unless otherwise specified, all measurements are expressed in mm.

37
IP2160EN - 2017-04-12
7.2 Base plate position
[1] Insert the anchor ties into the base plate and fix them with the supplied nuts.
[2] Insert the screws in the base plate, secure them with the nuts and then bend the metal tab to
prevent the screw from coming out.
Extract the preformed ties with a downwards movement using a hammer to ensure correct
anchorage to the concrete.
- Make a concrete base with the anchor ties and base plate embedded, which must be level and
clean and of the size indicated in the figure.
i
NB: if the concrete base has already been made, base plate [2] can be fixed using M8
plugs (not supplied).
OPENING
160
X+25 [*]
70[**]
min
40 [**]
Ø80 90°
300
335
1
[*] CROSSCRN2
[*] CROSSCRI
X=40
[**] NES100CKT
M12
low type
OPENING
160
X+25 [*]
70 [**] Ø60
Ø9
min
40[**]
300
340
[*] CROSSCRN2
[*] CROSSCRI
X=40
[**] NES100CKT
1
22a
2b
NES100PSU
M12-low
type
M12
low type

38
IP2160EN - 2017-04-12
- Release the gearmotor [1] (see OPERATING INSTRUCTIONS). Loosen the front screw [2] and
remove the casing by pressing on its sides [3-4].
- Place the gearmotor on the base plate.
- Adjustthe gearmotorhorizontallybyslidingitalongthe slotsofthegearmotorbaseandverticallywith
four levelling screws [A].
NB: during the vertical adjustment, keep the gearmotor slightly raised from the base plate so
that the rack can be fixed and subsequent adjustments are possible.
- After adjusting, fix the gearmotor using screws [B].
7.3 Gearmotor installation
WARNING: The gearmotor must be suitably raised from the ground to avoid flooding.
X
105
-15 +10
±5
A
B
M12-low type
M12
3
3
2
4
1

39
IP2160EN - 2017-04-12
- Release the gearmotor (see OPERATING INSTRUCTIONS) and open the gate.
- Place the rack against the pinion and sliding the gate manually fix it along its whole length.
NB: To make it easier to align the rods correctly, use a scrap piece of rack and rest it underneath
the junction point, as shown in the figure detail.
- Once fixed, vertically adjust the gearmotor to give a play of about 2 to 3 mm between the pinion
and the rack.
- Secure the gearmotor.
- Slightly lubricate the rack and pinion after assembly.
Manually check that the gate slides evenly and without friction.
7.4 Rack installation
2÷3
95

40
IP2160EN - 2017-04-12
7.5 Operation with virtual encoder
7.6 Magnetic limit switch installation and adjustment
NEOS gearmotors do not require limit switches because they have a virtual encoder.
Mechanical opening and closing end stops must be installed.
The gate automatically slows when approaching the end stops.
WARNING: when the gate reaches the opening or closing limit stop, it reverses briefly to facilitate
manual release of the gearmotor.
For the installation of the limit switch kit, refer to the Nes100FCM manual.
- Manually place the wing in the open position and fix limit switch brackets [A] and [B] on rack
[C]. Repeat this operation with the wing in the closed position.
- After a few manoeuvres, adjust the position of limit switch brackets [A] and [B] so that the gate
stops about 20 mm before reaching the opening and closing mechanical stops.
i
The limit switch kit is optional and is used to stop the gate before it reaches the opening
and closing mechanical stops.
With a limit switch installed, slowdown is carried out at regulated power to overcome
possible friction.
OPENING
~20
A BC

41
IP2160EN - 2017-04-12
1
12
- Release the gearmotor (see OPERATING INSTRUCTIONS).
- [1] Remove pinion [12].
- [2] Fix pinion supporting plate [A] to the gearmotor.
- Insert pinions [B] as illustrated in the diagram.
- [3] Pass the chain between the pinions by hand.
- Fix cover plate [C].
2
A
B
B
C
NB: Install the chain drive kit before securing the gearmotor to the base plate.
7.7 Chain drive kit installation
i
- Move the wing into the open position by hand and fix brackets [D] on the wing as illustrated in
the diagram.
- Connect chain [E], which was previously assembled on the gearmotor, to tie rod [F] and fix it
to bracket [D].
- Fix bracket [D] on the opposite side of the gate. Connect chain [E] to tie rod [F] and fix it to
bracket [D] (cut the excess chain).
min 50
40
90
E F D G
E
F
G
D

42
IP2160EN - 2017-04-12
NB: Make sure that the distance between the pinion centre and tie rod [F] is correct when the
gate is fully open and closed.
- Secure the chain with nuts [G].
- Tighten the chain [E] with the tie rods [F].
- Slightly lubricate the chain [E] and the pinions after assembly.
WARNING: when the chain traction kit is fitted, the gearmotor drive direction is inverted.
Right-hand opening
Left-hand opening

43
IP2160EN - 2017-04-12
Before connecting the power supply, make sure the plate data correspond to that of the
mains power supply.
An omnipolar disconnection switch with a contact opening distance of at least 3mm must
be fitted on the mains supply.
Check there is an adequate residual current circuit breaker and overcurrent cutout upstream
of the electrical system.
For the power supply, use a H05RN-F 3G1.5 type electric cable. Connect it to terminals L (brown),
N (blue), (yellow/green) inside the automation.
NOTE: the maximum permisible section of the wire is AWG14 (2 mm2).
Unsheathe the power supply cable in line with the terminal, and use a cable fastener to hold it
in place (see ref. B).
In order to comply with essential requirements of standards in force, reclose the cover once
the wires have been connected to the terminal.
In the external automation section, the connections to the mains power supply and any other low
voltage wires (230V) must be made on an independent channel separated from the connections
to the command and safety devices (SELV = Safety Extra Low Voltage).
The channel must penetrate the automation through the holes on the base plate by a few cen-
timetres.
Make sure there are no sharp edges that may damage the power supply cable.
Make sure the mains power wires (230V) and the accessory wires (24V) are separated. The cables
must be double insulated. Unsheathe them in line with the relative connection terminals, and
use cable fasteners (see ref. A) or straps (not supplied by us) to hold them in place.
8. Electrical connections
Assicurarsi che il conduttore
giallo verde sia almeno 30 mm
più lungo dei conduttori marrone e blu
L
N
1
2
A
B
Fascetta non di nostra fornitura
NB: the electrical wiring and start-up of the gearmotors is shown in the CS12E and CS12M
control panel installation manuals.
i
Make sure that the yellow-green
conductor is at least 30 mm longer
than the brown and blue conductors
Tie not supplied

44
IP2160EN - 2017-04-12
Perform the following operations and checks every 6 months, according to the intensity of use of
the automation.
Disconnect the 230 V~ power supply and batteries (if fitted) and release the gearmotor:
- Visually check that the gate, the fixing brackets and existing structure have suitable mechanical
strength and are in good condition.
- Check the gate-gearmotor alignment, the distance (2-3 mm) between the groove of the pinion
and the crest of the rack.
- Clean the wheel's sliding guide, the rack and pinion of the gearmotor and slightly lubricate
the rack and pinion. Manually check that the gate slides evenly and without friction.
Connect the 230 V~ power supply and batteries (if fitted) and lock the gearmotor:
- Make sure the limit switches are working correctly.
- Check the power adjustment.
- Check that all control and safety functions are working correctly.
NB: For spare parts, see the spares price list.
9. Routine maintenance plan
i
Additional photocells can be installed inside the gearmotor casing of Ditec NEOS, to protect both
opening and closing movements by using the LIN2 photocell.
Fit a receiver (RX) or a transmitter (TX) as shown in the figure.
Installation of the photocells must comply with standards EN12453 and EN12445.
WARNING: the photocell receiver (RX) and transmitter (TX) may also be installed at two different
heights, the maximum permissible difference in height being 300 mm.
Electrical connections
Connect the N.C. contact to the safety or stop contacts of the control panel.
i
For further informations, refer to the photocell installation manual.
8.1 Installation of internal photocell
LIN2
OPENING
TX
TX
TX
RX
RX RX

45
IP2160EN - 2017-04-12
DETACH AND DELIVER TO THE CUSTOMER
Operating instructions
General precautions for safe use
• Failure to observe the information in the User Manual may
lead to personal injury or damage to the equipment.
These instructions must be kept and forwarded to all possible
future users of the system.
• The sliding gate must only be used for the specific purpose
for which it was designed. Any other use should be considered
improper and therefore dangerous. The manufacturer cannot
be held responsible for any damage caused by improper, in-
correct or unreasonable use.
• Do not use the sliding gate if it needs repairing or adjusting.
Disconnect the power supply when carrying out cleaning or
maintenance tasks.
• The motorised gate may be used by children over the age of 8
and by people with reduced physical, sensorial or mental abili-
ties, or lack of experience or knowledge, as long as they are
properly supervised or have been instructed in the safe use of
the device and the relative hazards.
• Any cleaning or maintenance work by the user must be carried
out directly by a responsible person or under his/her supervi-
sion.
• Do not allow children to play or stay near the sliding gate. Keep
remote controls and/or any other command devices out of the
reach of children, to prevent the sliding gate being accidentally
activated.

46
IP2160EN - 2017-04-12
DETACH AND DELIVER TO THE CUSTOMER
Manual release instructions
Technical specifications
Manufacturer: Entrematic Group AB
Address: Lodjursgatan 10, SE-261 44 Landskrona, Sweden
Type: NES300EH NES300EHP NES400EH NES400EHP NES400EHJ
Power 230V~ 50/60 Hz 230V~ 50/60 Hz 230V~ 50/60 Hz 230V~ 50/60 Hz 120V~ 50/60 Hz
Power 1.2 A 1.2 A 1.2 A 1.2 A 2.4 A
Fuse F1.6 A F2 A F4 A
Ambient temperature -20°C +55°C
Degree of protection IP24
Control panel CS12E CS12M CS12E CS12M CS12E
Acoustic pressure <70 dB(A)
Certifications: Certifications of third parties, supplied by accredited certification bodies and valid for us-
age safety. Refer to the Conformity Declaration.
Manufacturer: Entrematic Group AB
Address: Lodjursgatan 10, SE-261 44 Landskrona, Sweden
Type: NES600EH NES600EHP NES600EHJ NES1000EHP NES1000EHPJ
Power 230V~ 50/60 Hz 230V~ 50/60 Hz 120V~ 50/60 Hz 230V~ 50/60 Hz 120V~ 50/60 Hz
Power 1.5 A (300W) 1.5 A (300W) 3 A (300W) 2 A (400W) 4 A (400W)
Fuse F2 A F4 A F2.5 A F6.3 A
Ambient temperature -20°C +55°C
Degree of protection IP24
Control panel CS12E CS12M CS12E CS12M CS12M
Acoustic pressure <70 dB(A)
Certifications: Certifications of third parties, supplied by accredited certification bodies and valid for us-
age safety. Refer to the Conformity Declaration.
In the event of a fault or power failure, insert the key and
turn it clockwise and completely open the hatch. Manually
open the gate.
To lock the gate again, close the hatch, turn the key anticlock-
wise and remove the key.
WARNING: the gate lock and release operations
must be performed with the motor idle.
Do not enter within the operating range of the gate.
When the hatch is closed but the key is still
horizontal, the release microswitch is open and all
manoeuvres are prevented.