Environmental Water Systems EWS-IRON-1054-A User manual
1
PRODUCT AND INSTALLATION MANUAL
Iron Removal Systems
MODEL NUMBERS:
EWS-IRON-1054-A, EWS-IRON-1354-A
Retain this Product & Installation Manual
for Helpful Information
Please Register Your System
Revised 12/01/2017 V: 1.7
2
If you don’t read this service guide at least read these 7 simple steps
SIMPLE STEPS FOR A CORRECT INSTALLATION AND A HAPPY CUSTOMER
1.
Set up system and install it on the main water supply coming into
the home
Page 7-8
2.
Page 9
3.
Install a proper drain line with an air gap
Page 10
4.
standard outlet and set the time of day
Page 11-12
5.
up procedure (see complete start up procedure)
Page 12-13
6.
Page 14
7.
and drain water heater if needed.
Page 15
inlet
outlet
closed
inlet
outlet
closed
inlet
outlet
5.
6.
7.
6.
2.
3.
4.
please see the great information available in this service manual
Avoid Problems and Callbacks
Create Happy Customers
3
SIMPLE STEPS FOR A CORRECT INSTALLATION AND HAPPY CUSTOMER ...................................... 2
INSTALLATION DIMENSIONS SYSTEMS ................................................................................................. 4
ON SITE ASSEMBLY PROCEDURE .......................................................................................................... 5
IMPORTANT SAFETY INFORMATION – All Systems
Instructions Before Using ........................................................................................................ 6
LOCATION AND SETUP - All Systems ....................................................................................................... 7
Unpacking and Inspection
Where to Install the System
Drain Location
INSTALLATION INSTRUCTIONS - All Systems
Drain Line .................................................................................................................................. 10
START-UP PROCEDURES - All Systems
Set the Time of Day ..................................................................................................................... 12
Tank Fill Slowly .................................................................................................................................. 13
Flushing the System Procedure ........................................................................................................ 14
Last Steps Before Leaving the System ........................................................................................... 14
Repeat Flushing (if needed)
Open Outlet Side of Bypass
System Ready for Use
Run Water throughout the Home
Touch Screen other options ............................................................................................................ 16
Product Blow-Out (for illustration purposes) .............................................................................. 17
Warranty .................................................................................................................................. 19
www.ewswater.com o. 702.256.8182; (m-f; 8:00am-4:30pm; PST) f. 702.256.3744 e-mail. customerservice@ewswater.com
table of contents
4
For Illustration Purposes Only:
On-Site Assembly Required
Due to shipping weight for all Iron systems,
Flexible Connections Required:
Drain Line Air Gap Required and Spring Check Highly Recommended:
Complete setup, install and startup of these systems can be found in this Product and Installation Guide
*Not Supplied:
For Illustration Purposes Only:
All measurements
and system
heights may
have
variances
up to 1”.
Pictured:
EWS-IRON-1354-A
installation dimensions - Model #’s EWS-IRON-1054-A, EWS-IRON-1354-A
overall
height
67”
height
to center
of
tank
height
54”
self leveling
base
tank width 13”
depth: minimum 22” needed for proper installation
Valve (front view)
Not pictured:
Electric Transformer,
Bypass Valve and
Adaptors to the rear
of the Valve.
overall
height
67”
height
to center
of
tank
height
54”
tank width 10”
depth: minimum 22” needed for proper installation
Valve (front view)
Not pictured:
Electric Transformer,
Bypass Valve and
Adaptors to the rear
of the Valve.
Pictured:
EWS-IRON-1054-A
If installing other
-
tion to this Iron Sys-
tem - see Page 18 in
the Service Manual
for proper order of
installation
5
assembly instructions for larger systems
Check to see if you have all the boxes before assembly - Below is the box count for each system
______________________________________________________
_______
6 Total
____________________________________________________
_______
8 Total
simple steps for proper assembly - no tools required
Caution:
Note:
Caution:
6. Using the supplied Funnel - Load the Tank in the following order:
--------------------------------------------------------------------------------------
A: 1st
Caution:
Caution:
Caution:
Note:
8. Installation of the Valve onto the Tank:
---------------------------------------------------
Warning:
For Illustration Purposes Only:
6
Instructions Before Using
Handle all components of the system with care. Do not drop, drag or turn components upside down.
WARNING: Failure to setup, install and startup the system correctly in any manner voids the warranty.
CONNECTIONS:
REQUIRED:
WARNING:
Do not use pipe dope or pipe joint compound.
EXISTING PLUMBING:
this system.
ELECTRICAL: All Systems in this guide (USA versions) use 12 volt transformer for electrical power.
electric outlet and transformer do not come in contact with water.
CAUTION:
INSTALLATION LOCATION:
- Install system in a protected area.
- Do not install in direct sunlight. Heat from sun may cause damage. Protect from sun, rain, wind, etc.
- See “Where to Install the System” on page 8 of this manual for complete information.
WATER TEMPERATURE:
WARNING:
IRON SYSTEMS
PRESSURE:
WARNING:
FLOW RATE:
8 gpm for 1054 systems and 12 gpm for 1354 systems in order for system to function properly.
IMPORTANT SAFETY INFORMATION - ALL SYSTEMS
CAUTION: Read and follow the information in this manual to minimize the risk
of electric shock or personal injury.
IMPORTANT!
IMPORTANT!
state and local codes, law, and regulations.
CAUTION:
water periodically to verify that the system is performing satisfactorily.
7
IMPORTANT SAFETY INFORMATION - ALL SYSTEMS location and setup
UNPACKING AND INSPECTION -
WHERE TO INSTALL THE SYSTEM
electrical panels. Always connect the system prior to the water heater(s).
CAUTION:
CAUTION: I
NOTE:
DRAIN LOCATION
Highly Recommended:
REQUIRED:
REQUIRED: and
CAUTION:
to other water lines.
OUTSIDE INSTALLATION
Helpful Hint to Protect your System:
REQUIRED: Place system into a heavy-duty, corrugated, solid wall culvert pipe with a minimum diameter size 2” larger than the
REQUIRED:
this section.
Helpful Hint:
8
closed position
install 1” adaptors
NOTE:
Install in the correct direction
valve
installation instructions - all iron systems
INSTALLATION
1. Turn off gas or electric supply to the water heater(s).
2. Turn off the main water supply.
3. Open a hot and cold faucet to drain house water pipes.
NOTE:
4.
CAUTION:
However in transportation, delivery and movement to the installation position this connection may
have loosened. It is important to make sure this connection is tight and if necessary hand-tighten
only in a clockwise direction to ensure this connection.
NOTE:
Refer to “Instructions Before Using” on page 6 and “Where To Install The System” on page 7.
5. VALVE PARTS AND FINAL ASSEMBLY:
a. Locate the Bypass Valve:
Connect Bypass to the Valve.
NOTE:
b.
Connect the Adaptors to the Bypass and the Brass Fittings as pictured below.
NOTE:
CAUTION:
WARNING: All connections:
WARNING: All connections: Hand tighten only. Do not overtighten. Make sure o-ring and white retainer ring are in place.
c. Locate the Electric Transformer:
Connect Transformer to the Valve
NOTE: Input into the Valve is just like
those used in computer laptops
and many electronic devices.
Locate the input jack on the lower right side or the drain side of the valve.
end into an outlet until instructed to do so towards the end of installation.
input into valve
WARNING:
Always keep inlet and
until instructed to open
NOTE:
ok we are ready to make the plumbing connections
The cord is
represented
in white for
illustration
purposes only
with air injector
9
For Illustration Purposes Only:
not supplied
closed position
keep closed until
startup procedure
inlet outlet
1” adaptors
from main supply to the home
connection
connection
top view:
valve not pictured for this illustration
front
included:
included:
6. Locate water line or pipe to be cut and make sure of direction of water ow.
CAUTION:
7. Plumb Inlet and Outlet Connections to and from the system.
REQUIRED:
WARNING: Be sure the incoming water supply is connected to the inlet port of the valve.
WARNING:
connections which will result in leak issues under pressure.
WARNING:
CAUTION:
CAUTION:
WARNING:
WARNING:
WARNING:
WARNING:
CAUTION:
installation Instructions - all iron systems - plumbing connections
with air injector
1” adaptors
10installation Instructions - all systems - drain connections
NOTE: Secure (clamp, tie or wire) installed drain line near drain point to prevent movement and avoid any
NOTE:
for all systems on page 17) for up to 23 minutes every 6 days to avoid water damage.
CAUTION:
INFORMATION FOR AN OUTSIDE DRAIN LINE:
-
minutes every 6 days to avoid water damage.
REQUIRED FOR AN OUTSIDE INSTALLATION:
minimum
1” air gap
normal
ow
8.
NOTE:
Drain adaptor can swivel.
WARNING:
HINT: Install a union on the drain line in order make any service or need to disconnect easier in
the future.
9.
HIGHLY RECOMMENDED:
REQUIRED:
Similar to any washing machine, this sytem must have a minumum of a 1” air
REQUIRED:
and install a non-restrictive spring check
CAUTION:
11
installation Instructions - all systems - electrical connections
INSTALL ELECTRICAL CONNECTION
10.
If you haven’t already done so from Page 8, 5c. Plug outlet from transformer into the
input on the valve. The input is in a protected area to avoid any damage from water.
See input location on the valve on Page 8
NOTE: POWER CONSUMPTION
CAUTION:
connections to maintain the continuity of the systems’ ground. Properly ground system to conform
with all codes and ordinances.
touch screen home page and what you see when the system is on
ok, lets, set the clock
is run through the start up (right).
Just like a new smart phone, it may take a moment to adjust to the screen.
Water Treatment
treatment
custom
11 h
59 m
wed
12:01 am
Home Page
once the system
is plugged in this
is the 1st screen
you will see
NOTE:
changes needed.
System does not need any
additional programming.
Please follow the instructions
and allow system to run through
the pre-programmed start-up
12
setting the clock
now it’s time to ll the tank and ush the system
11.
The Day And Time screen will appear
Note: Day of the Week will adjust automatically
Day Month Year
Hour Minute
AM
or
PM
Day of the Week
Day And Time
CLEAR THE PLUMBING LINES AND CONNECTIONS
12. 1- Keep the inlet and outlet closed to and from the system
2 - Turn on main water supply
3
4
CAUTION:
**
**
NOTE:
changes needed.
System does not need any
additional programming.
Please follow the instructions
and allow system to run through
the pre-programmed start-up
13
start up procedure - ll the tank and ush the system
15.
OPEN THE INLET ON THE BYPASS SLOWLY (inlet open position)
NOTE:
NOTE:
13 m
0 s
system is now ushing on its’ own and you are almost done
START UP TO FLUSH THE SYSTEM
14. Press the Cycle button
in the lower right corner.
Screen will change
Press the now button
This is a 14 minute cycle
open inlet only
during system start up
inlet
open
open
inlet
slightly
inlet
now now
at regen time
Regeneration
backwash
outlet
closed
outlet
closed
valve
valve
FILL THE TANK - SLOWLY
13.
Open the inlet slightly on the bypass
as shown
CAUTION:
13 m
59 s
Water Treatment
treatment
custom
11 h
59 m
wed
12:01 am
1667
G
Water Treatment
backwash
custom
13 m
59 s
wed
12:01 am
14
These are the system start up and self-cleaning cycles and the duration:
this is what the system is doing and we want to see clear drain water
backwash
draw
rapid rinse
Reminder: Open inlet completely after 1 minute when the it reads
Note:
time to put the system in service and check your work
and is ready for service
The valve is metered and the system will
self clean when 1,667 gallons are used or
on the 6th day at 1am, which ever
16.
If the water is running clear - proceed to Step #17.
If the water remains grey - go back to Step #14 on Page 13
CAUTION: If the drain water remains grey,
minimum
1” air gap
look for clear
water coming
from the drain
WARNING:
13 m
0 s
Water Treatment
treatment
custom
4000
G
wed
12:40 am
1667
G
15
WARNING:
17. OPEN OUTLET ON THE BYPASS
SYSTEM FINAL SERVICE POSITION
18. System is ready for use.
Turn on gas or electric supply to the water heater(s).
To ready home for ltered water, please ush all the water throughout the home.
remove the aerators or any restriction at the end of the faucets,
dispose of any ice previously made
run water throughout home for 5 minutes.
19. Final Checklist
check all connections,
make sure drain is correctly installed and drain water was running clear.
NOTE:
NOTE:
If home is a year or more old, it is highly recommended that all water heaters or tankless on-demand
Please review Page 6 “Instructions Before Using” for e
that will effect the performance of this system.
open outlet for service and go through a checklist to avoid any issues
Avoid Problems and Callbacks
Create Happy Customers
system is in service position inlet
outlet
valve
16
other buttons you can push on the screen
system has encountered and the amount of gallons that have passed through the system.
Note: Flow rate may determine if a leak is occuring in your home.
Home: Press and return to the
Home screen
previous screen
Advance: Press and advance to
or change and moves to
Water Treatment
treatment
custom
4000
G
mon
10:30 am
Vacation Mode
Diagnostics
Settings
Vacation Mode:
normal setting.
Note:
The upper right screen will return
use 1,667 gallons of water or on
Recommended:
Upon return from vacation, press
-
1667
G
17
Underbed:
Filtration:
EWS proprietary, high grade, iron reduction
1054 system: 1.5 cu.ft.
1354 system: 2.5 cu.ft.
self leveling base
Riser Distribution ORing
Valve Tank ORing
Bypass:
Direct threaded attachment to
needed. Shown in closed po-
sition
Tank:
Adaptor 1”:
Direct threaded attachment to
main water lines.
Valve - Outlet Side Valve - Inlet Side
Front View;
Touch Screen Valve
cleaning of the system
Tank Wrap:
eco-cover for tank with contact
infomation and information impor-
tant for the proper application of
the system.
Drain (grey) Clip:
Secures drain adaptor to
valve drain port
parts breakdown - iron systems (for illustration only)
Riser::
With upper diffuser used
with air injection valve
riser with lower screen
system from a front view.
-
-
ethelyene interior with structured
2.5” opening:
Brass Spring Check:
Install on incoming line
Brass Line Flow Control:
Install on outgoing line
Injection:
NOTE:
Drain Adaptor
Drain Flow Rates:
1054 - 8gpm,
1354 - 12gpm
All Systems:
40 minutes @ .25gpm
Electric:
Note: drain line to properly
air gapped location is not
18
CONDITIONS
Source Water - Test Results
Pre-Treatment:
decaying vegetation, organic
Tannins (yellow)
(as needed)
location or sequence of tank may vary
Iron Removal (as needed):
Iron (red or pinkish)
Pre-Sediment Filtration (as needed):
Silt, dirt, heavy particulate matter
location or sequence of unit may vary
pH Balancing (as needed):
Low pH, less then 6.6, corrosive, acidic water
location or sequence of unit may vary
Point of Entry Filtration (as needed):
solvents, dyes, fuels, odor, taste, clarity
Point of Use Filtration (as needed):
Dependent upon test results, removal
APPLICATIONS
Based on Test Results
Chlorination/Chemical Feed
(as needed)
Ozonation
UV (only safeguard, not a solution)
Storage
8 gpm (or 12 gpm for all 1354 tank systems)
Media Systems
-
-
ing Reagent System
Series - Filtration only
EWS Series -
Various Drinking Water Systems
or (pictured) Reverse Osmosis Units
C
W
-
mize water issues for use in the home.
schematic for varied or difcult well water conditions
19
Failure
to do so voids the warranty unless restricted by state regulations.
Know Your Water:
only provides metered valving in its line of softeners.
-
-
Notication:
Limited Warranty:
paragraphs:
Aesthetic, non-health related, or constituents without set federal standards may be part of water testing but are insufcient to determine proper application of any
water ltration or treatment device.
-
This warranty is not a warranty of merchantability, tness, taste, aesthetics, and/or performance that may be personal and of subjective opinion and that does not
relate to the performance of any system.
Warranty Notication - As Published and Available Online
Warranty Information and the Purchaser’s Responsibility
20
EWS Logo and Environmental Water Systems are Registered Trademarks and the Property of EWS, Inc.
EWS is a Proud Contributor and Sponsor of Organizations Dedicated to Improving
Health, Well-Being and the Environment
• ••••
Oceans Inland Water Ways Wetlands Forestry Soil Air
•
••• • •
••
ALL FILTRATION PRODUCT PROUDLY MADE & ASSEMBLED IN THE USA
This manual suits for next models
1
Table of contents
Other Environmental Water Systems Water Filtration System manuals
Environmental Water Systems
Environmental Water Systems ESSENTIAL SS-1.0 User manual
Environmental Water Systems
Environmental Water Systems EWS-1354-1.5 User manual
Environmental Water Systems
Environmental Water Systems EWS-1354-1.5 User manual
Environmental Water Systems
Environmental Water Systems BB-FUGAC200A-1 User manual
Environmental Water Systems
Environmental Water Systems EWS-1054 Guide
Environmental Water Systems
Environmental Water Systems EWS-SPECTRUM User manual
Environmental Water Systems
Environmental Water Systems EWS-1665-2 User manual
Environmental Water Systems
Environmental Water Systems Spectrum CS-EWS-1354-7000 User manual
Environmental Water Systems
Environmental Water Systems EWS-SPECTRUM-V2 User manual
Environmental Water Systems
Environmental Water Systems DWS User manual
Environmental Water Systems
Environmental Water Systems EWS-HEATER-GUARD-3/4 User manual
Environmental Water Systems
Environmental Water Systems BB 1" SETUP User manual
Environmental Water Systems
Environmental Water Systems RU500T35 w/BP User manual
Environmental Water Systems
Environmental Water Systems PRESED-1354 User manual
