Environmental Water Systems EWS-1354-1.5 User manual
1
PRODUCT AND INSTALLATION MANUAL
Whole Home and Light Commercial
Water Filtration Systems
for 1.5” incoming line size
MODEL NUMBERS:
Whole Home and Light Commercial Water Filtration & Conditioning Systems:
EWS-1354-1.5
Whole Home and Light Commercial Water Filtration Systems:
CWL-1354-1.5
Retain this Product & Installation Manual
for Helpful Information
Please Register Your System
Revised 12/01/2017 V: N.1.0
2
If you don’t read this service guide at least read these 7 simple steps
SIMPLE STEPS FOR A CORRECT INSTALLATION AND A HAPPY CUSTOMER
1.
Set up system and install it on the main water supply coming into
the home
Page 6-7
2.
Set up a bypass (see illustration ) and use corrugated
plumbing connections
Page 7-9
3.
Install a proper drain line with an air gap
Page 10
4.
Plug in the system into a standard outlet and set the time of day
Page 11
5.
the start up procedure. Keep bypass and outgoing valve closed
Page 12
6.
Page 13
7.
-
ed.
Page 14
5.
7.
2.
3.
please see the great information available in this service manual
Avoid Problems and Callbacks
Create Happy Customers
valve
open
valve
open
valve
closed
inlet
to valve
outlet
from valve
in raw
water supply
to home
bypass
closed
valve
closed
valve
open
valve
closed
to home
in raw
water supply
bypass
closed
inlet
to valve
outlet
from valve
to home
in raw
water supply
bypass
closed
inlet
to valve
outlet
from valve
Service
Position
3
installation dimensions
For Illustration Purposes Only:
Plumber installed bypass is required.
overall
height
63”
height
to center
incomng
56-3/4”
height
to center
outgoing
58”
height
to center
drain
57-5/8”
height
54”
Flexible Connections Required:
Drain Line Air Gap Required and Spring Check Highly Recommended:
Please see information for proper drain line installation in the Product and Installation Guide
depth: minimum 22” needed for proper installation
Complete setup, install and startup of these systems can be found in this Product and Installation Guide
*Not Supplied:
For Illustration Purposes Only:
Valve (front view)
Not pictured:
Adaptors to the rear
All measurements are
and system heights
may have
variances up to 1”.
Pictured:
EWS-1354-1.5
CWL-1354-1.5
CAUTION: If installing other equipment in addition to this System - Contact customer service for proper order of installation
Plumber installed
bypass is required
all incoming/outgoing piping and
3 ball valves are not supplied
For Illustration Purposes Only:
with the valve.
4
SIMPLE STEPS FOR A CORRECT INSTALLATION AND HAPPY CUSTOMER ...................................... 2
INSTALLATION DIMENSIONS FOR EWS-1354-1.5 OR CWL-1354-1.5 .................................................. 3
IMPORTANT SAFETY INFORMATION – All Systems
Instructions Before Using ........................................................................................................ 5
LOCATION AND SETUP - All Systems ....................................................................................................... 6
Where to Install the System
Drain Location
Outside Installation (where applicable)
INSTALLATION INSTRUCTIONS - All Systems
Plumbing Connections and Bypass ........................................................................................... 7
Drain Line .................................................................................................................................. 10
Electrical Connection ..................................................................................................................... 11
START-UP PROCEDURES - All Systems
Set the Time of Day ..................................................................................................................... 12
Flushing the System Procedure ........................................................................................................ 13
Last Steps Before Leaving the System ........................................................................................... 14
Repeat Flushing (if needed)
Open Outlet Side of Bypass
System Ready for Use
Run Water throughout the Home
Product Blow-Out (for illustration purposes) .............................................................................. 16
Warranty .................................................................................................................................. 17
or email the EWS crew @ customerservice@ewswater.com or call us @ 702.256.8182
www.ewswater.com o. 702.256.8182; (m-f; 8:00am-4:30pm; PST) f. 702.256.3744 e-mail. customerservice@ewswater.com
table of contents
PRODUCT PERFORMANCE AND GENERAL TERMS AND STANDARD CONDITIONS OF SALE ARE
5
Instructions Before Using
WARNING:
CONNECTIONS: Perform installation according to state and local plumbing codes.
REQUIRED:
WARNING:
Do not use pipe dope or pipe joint compound.
EXISTING PLUMBING:
this system.
ELECTRICAL: All Systems in this guide (USA versions) use 24 volt transformer for electrical power.
Always use the supplied power cord and transformer. Plug power cord into a standard 110/115/120
electric outlet and transformer do not come in contact with water.
CAUTION: Plumber installed jumper between inlet and outlet connections may be required to maintain the
plumbing system ground. Properly ground system to conform with all codes and ordinances.
INSTALLATION LOCATION:
- Install system in a protected area.
- Always connect the system to the main water supply pipe feeding the entire home before the water heater(s).
- See “Where to Install the System” on page 8 of this manual for complete information.
WATER TEMPERATURE:
WARNING:
PRESSURE:
reducing valve if necessary to prevent high pressure and problem pressure surges above 75 psi.
WARNING:
IMPORTANT SAFETY INFORMATION - ALL SYSTEMS
CAUTION:
IMPORTANT!
EWS customer service or consult a professional plumber.
IMPORTANT! This system must be installed in compliance with applicable
CAUTION:
without adequate disinfection. Well water needs to be properly and completely
water periodically to verify that the system is performing satisfactorily.
6
location and setup
UNPACKING AND INSPECTION -
WHERE TO INSTALL THE SYSTEM
A standard grounded and unswitched 110/115/120v electrical outlet is needed to plug in the transformer. If outlet is over 16 feet away
Do not cut or splice original equipment.
electrical panels. Always connect the system prior to the water heater(s).
CAUTION:
CAUTION: I
Any questions? Please contact EWS for proper order of installation.
NOTE:
DRAIN LOCATION
Place the system as close as possible to a vented sewer drain with a “P” trap or some other drain location.
Highly Recommended:
REQUIRED:
REQUIRED: and
drain line is being routed outside.
CAUTION:
Consider the reuse of drain water as an alternative to simply going down the drain.
to other water lines.
OUTSIDE INSTALLATION
Before Using” on Page 5 in this manual. The system is weather resistant but not weather-proof and it is a requirement to protect the
Helpful Hint to Protect your System:
REQUIRED:
REQUIRED: Protect top portion and valve of the system that has been placed into the culvert pipe by following all information in
this section.
Helpful Hint:
7
INSTALLATION
1. Turn off gas or electric supply to the water heater(s).
2. Turn off the main water supply.
3. Open a hot and cold faucet to drain house water pipes.
NOTE: Keep those hot and cold faucets open until these instructions tell you to close.
4.
CAUTION:
NOTE:
Refer to “Instructions Before Using” on page 5 and “Where To Install The System” on page 6.
NOTE:
5. Locate water line or pipe to be cut and make sure of direction of water ow.
CAUTION:
6. Plumb a Bypass and make Inlet and Outlet Connections to and from the system.
Bypass must have ball valves on the incoming and outgoing lines and an additional ball valve between the two
lines (as illustrated on Pages 8 & 9) in order to provide a bypass in case of maintenance or any issues. This pro-
vides water to the home even if the incoming and outgoing lines to the system are closed and the system is off.
REQUIRED:
by local plumbing code to connect directly into the valve (as illustrated on Pages 8 & 9).
WARNING: Be sure the incoming raw water supply is connected to the inlet port of the valve.
NOTE:
installation Instructions - all systems - plumbing connections - bypass
check out pages 8 & 9 for valve and bypass pictures
8
CAUTION:
WARNING:
WARNING:
**
pressure or pressure variances.
WARNING: All threaded connections:
Do not use pipe joint compound or pipe dope.
Hand tighten only. Do not overtighten.
valve - big picture of ow direction in & out
Outlet
outgoing
to the home
Inlet
incoming
raw water
from supply
Drain Line
9
order for the correct connection into the inlet side and the
outlet side of this valve.
In & out valves are open and bypass valve in closed position
CAUTION: All valves should remain closed until startup procedure
to home
in raw
water supply
bypass
closed
connect to
inlet
connect to
outlet
Plumber installed
bypass is required
not supplied
FOR ILLUSTRATION
PURPOSES ONLY:
RECOMMENDATION
:
1. Build your bypass.
2. Secure against the wall.
NOTE:
system close to the wall.
connect to the proper inlet and out of the valve and
assist with the installation where rough plumbing and
bypass - big picture with some great information
10
installation Instructions - all systems - drain connections
NOTE:
possible water damage.
NOTE:
water damage.
water conditions.
CAUTION:
drain point. (see illustration above)
INFORMATION FOR AN OUTSIDE DRAIN LINE:
-
and absorb 7 gpm (bath tub) for up to 20 minutes every 10 days to avoid water damage.
REQUIRED FOR AN OUTSIDE INSTALLATION:
minimum
1” air gap
normal
ow
7. Plumb rigid tubing only (PVC recommended if code applicable) directly to the 3/4” FNPT brass drain tting.
WARNING: Do not use vinyl tubing or any hose type material and clamps for the drain line.
HINT:
the future.
8. Connect and route the drain line to a vented sewer drain with a “P” trap or some other drain location.
Installation with an air gap is required.
HIGHLY RECOMMENDED:
REQUIRED: Air gap with proper ventilation is a requirement.
REQUIRED:
and
CAUTION: Never install drain line smaller than 3/4” in diameter.
Drain water is usable for watering and other uses and does not have to be wasted.
many problems associated with this or any system. Please read the instructions below to avoid any issues.
11
ok, lets, set the clock and start this system up
led screen and what you see when the system is on
installation Instructions - all systems - electrical connection
INSTALL ELECTRICAL CONNECTION
9. Connect electrical power by plugging the system nto a standard grounded and unswitched 110/115/120v electrical
outlet.
Do not cut or splice original equipment.
NOTE: POWER CONSUMPTION
CAUTION: If the home’s plumbing system is copper (or any metal) then it may be necessary to install a jumper.
connections to maintain the continuity of the systems’ ground. Properly ground system to conform
with all codes and ordinances.
4#_ SRV 00:00PM
REGEN IN 06 DAYS
Set Up Button
Adjusts Other Settings
as needed
Set Down Button
Adjusts Other Settings
as needed
Shift Button
Adjusts Cursor Position
Extra
Cycle
Button
Diagnostic Button
Last Two Regens
Status LED
Blue = In Service
Green = In Regen
Red = Error Mode
Green Display Screen
Time of Day
In Service
Alternates with Error Screen if
errors are present
Factory Pre-Set is every 6 days
Time of day
In Service
will read INI for 30-45 seconds
after a power failure reset or
programming
System #
4 Indicates a Filter System
or Light Commercial
NOTE:
Day & Time are the only changes needed.
System does not need any additional programming.
Please follow the instructions and allow system to
12
inlet supply
partial open
SET TIME OF DAY:
10:29PM
installation Instructions - all systems - set the clock
SET THE TIME OF DAY
10. a. Press and Hold the Up or Down Button for 2 seconds.
Time of Day Screen will appear
b. Press the Shift Button to select what digit you want to change
Note: The hour or minutes you are changing will be __ underlined.
c. Set the AM or PM by changing the time up or down until correct.
Extra
Cycle
Button
Shift
Button
Down or Up
Button
start up procedure - ll the tank and start to ush the system
FILL THE TANK - SLOWLY
12. Partially open the inlet as shown
CAUTION:
go to step 13 on next page and begin to ush the system
valve
closed
inlet
to valve
outlet
from valve
in raw
water supply
to home
bypass
closed
valve
closed
CLEAR THE PLUMBING LINES AND CONNECTIONS
11. 1- Keep the inlet and outlet closed to and from the system
2 - Turn on main water supply
3
through your plumbing connections before opening the inlet to the system or beginning the start up procedure
4
CAUTION: Debris may be present in the lines from closing and opening the main supply or from plumbing connections
made prior the system. We want to prevent any debris from entering the valve and causing damage to
require additional service or the purchase of new parts.
13
ush the system and what the system is doing
check the drain water and put the system in service
VALVE MOVING TO
HOME POSITION
These are the system start up and self-cleaning cycles and the duration:
CYCLE 1 00:09:59
BACK WASH
Cycle 1. Backwash: This cycle will count down and last 10 minutes.
Cycle 2. Slow Rinse: This cycle will count down and last 5 minutes.
Cycle 3. Rapid Rinse: This cycle will count down and last 10 minutes.
CYCLE 2 00:04:59
BRINE&SLOW RINSE
CYCLE 3 00:09:59
RAPID RINSE
4#_ SRV 00:00PM
REGEN IN 06 DAYS
START UP TO FLUSH THE SYSTEM
13. Press the Extra Cycle button
Screen will change to Cycle 1
14.
Slowly open the inlet only and keep outlet closed
Extra
Cycle
Button
CYCLE 1 00:09:59
BACK WASH
NOTE:
NOTE:
valve
open
valve
closed
to home
in raw
water supply
bypass
closed
inlet
to valve
outlet
from valve
NOTE:
Day & Time are the only
changes needed.
System does not need any
additional programming.
Please follow the instructions
and allow system to run through
the pre-programmed start-up
14
16. Open outlet and put the system in nal service position (see illustration below)
check the drain water and put system in service
15. Observe the drain water during Cycle 3. Rapid Rinse
If the water is running clear - proceed to Step #16.
If the water remains grey - go back to Step #13 on Page 13.
CAUTION:
until the water from the drain line runs clear.
minimum
1” air gap
water coming
from the drain
Extra
Cycle
Button
CYCLE 3 00:09:59
RAPID RINSE
This is the Service Position
inlet open from water supply to system
outlet open from system to home
bypass between the inlet and outlet is closed
valve
open valve
open
to home
in raw
water supply
bypass
closed
inlet
to valve
outlet
from valve
15
go through home checklist and check your work
WARNING:
17. System is ready for use.
Turn on gas or electric supply to the water heater(s).
To ready home for ltered water, please ush all the water throughout the home.
dispose of any ice previously made
run water throughout home for 5 minutes.
18. Final Checklist
NOTE:
NOTE:
Please review Page 5 “Instructions Before Using” for e
that will effect the performance of this system.
Avoid Problems and Callbacks
Create Happy Customers
16
Underbed:
30 lbs. for 1354-1.5 systems
Filtration:
1354-1.5 systems: 2.5 cu.ft.
ICN Riser & Manifold:
(EWS-1354-1.5)
Food & beverage rated pvc water
distribution riser with lower screen
and ICN Manifold for Conditioning.
EWS-1354-1.5 system - 2 ICN’s
self leveling base
Upper Valve Screen
Riser Distribution ORing
Valve Tank ORing
Tank:
-
4” opening
Valve - Outlet Side Valve - Inlet Side
Front View;
Fully Ported 1.5” Valve
4” valve base
Note - Freeboard:
cleaning of the system
Tank Wrap:
infomation and information impor-
tant for the proper application of
the system.
parts breakdown - all ews/cwl-1354-1.5 whole home ltration systems
(for illustration only)
Riser::
(CWL-1354-1.5)
Food & beverage rated
pvc water distribution
riser with lower screen
Below represents a fully assembled
system from a front view.
CAUTION: If installing other equipment in addition to this System - Contact customer service for proper order of installation
Electric:
24 volt plug & play transformer with 16’ cord
a doorbell
Brass Drain Adaptor (DLFC)
3/4” FTNP
(Pictured installed on the
valve inlet side)
Drain Flow Rates:
1354-1.5 - 7gpm
inlet connection
incoming raw water
supply
Outlet connection
water to the home
drain
17
Failure
to do so voids the warranty unless restricted by state regulations.
good customer service for years to come. Please see our privacy policy published in our website at www.ewswater.com.
Know Your Water:
any state or local requirements. Any problems should be reported to the appropriate agencies. Please acquire those municipal test results to become an informed consumer.
our “Guide for the Private Well Owner” on our website; www.ewswater.com. Review our section on well water testing and applications in our complete catalog with your local
only provides metered valving in its line of softeners.
issues and believe these rules are unenforcable. The consumer is ultimately responsible.
-
-
Notication:
Limited Warranty:
paragraphs:
valve body and electronics from date of purchase.
Aesthetic, non-health related, or constituents without set federal standards may be part of water testing but are insufcient to determine proper application of any
water ltration or treatment device.
-
This warranty is not a warranty of merchantability, tness, taste, aesthetics, and/or performance that may be personal and of subjective opinion and that does not
relate to the performance of any system.
Warranty Notication - As Published and Available Online
Warranty Information and the Purchaser’s Responsibility
18
19
left blank
20
EWS Logo and Environmental Water Systems are Registered Trademarks and the Property of EWS, Inc.
EWS is a Proud Contributor and Sponsor of Organizations Dedicated to Improving
Health, Well-Being and the Environment
• ••••
Oceans Inland Water Ways Wetlands Forestry Soil Air
•
••• • •
••
ALL FILTRATION PRODUCT PROUDLY MADE & ASSEMBLED IN THE USA
Other manuals for EWS-1354-1.5
1
This manual suits for next models
1
Table of contents
Other Environmental Water Systems Water Filtration System manuals
Environmental Water Systems
Environmental Water Systems BB-FUGAC200A-1 User manual
Environmental Water Systems
Environmental Water Systems EWS-1054 Guide
Environmental Water Systems
Environmental Water Systems EWS-IRON-1054-A User manual
Environmental Water Systems
Environmental Water Systems EWS-SPECTRUM User manual
Environmental Water Systems
Environmental Water Systems BB 1" SETUP User manual
Environmental Water Systems
Environmental Water Systems EWS-HEATER-GUARD-3/4 User manual
Environmental Water Systems
Environmental Water Systems EWS-1354-1.5 User manual
Environmental Water Systems
Environmental Water Systems Spectrum CS-EWS-1354-7000 User manual
Environmental Water Systems
Environmental Water Systems EWS-SPECTRUM-V2 User manual
Environmental Water Systems
Environmental Water Systems PRESED-1354 User manual
Environmental Water Systems
Environmental Water Systems ESSENTIAL SS-1.0 User manual
Environmental Water Systems
Environmental Water Systems DWS User manual
Environmental Water Systems
Environmental Water Systems EWS-1665-2 User manual
Environmental Water Systems
Environmental Water Systems RU500T35 w/BP User manual
Popular Water Filtration System manuals by other brands
Kenmore
Kenmore 625.382080 owner's manual
Pentair
Pentair THS Series Installation and user guide
Crystal Quest
Crystal Quest CQE-RC-00808 Installation and operation guide
Noble
Noble M20 Dual installation manual
Clearwater Spas
Clearwater Spas TPS Operation manual
AMI
AMI AAA-RO-50 Instructions manual for installation, operation and maintenance
Vetus
Vetus Sapro Installation instructions and operation manual
Atlantic Ultraviolet
Atlantic Ultraviolet Mighty Pure MP13A owner's manual
Purlette
Purlette PL400G owner's manual
Pentair
Pentair EVERPURE QL3B 7FC5 Installation, operation, maintenance guide
PONDTEAM
PONDTEAM Bioclear XL 40000 Instructions for use
AQUA SZUT
AQUA SZUT JUNIOR N instruction manual
