Epson A882181 User manual

EPSON
®
17” Super VGA
Color Monitor
(ModeI A882181)
U SER`S Guide
a
EPA POLLUTION PREVENTEI

FCC COMPLIANCE STATEMENT
FOR AMERICAN USERS
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio or
television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
lReorient or relocate the receiving antenna
lIncrease the separation between the equipment and receiver
lConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected
lConsult the dealer or an experienced radio/ TV technician for help
WARNING
The connection of a non-shielded equipment interface cable or a non-shielded power cable
to this equipment will invalidate the FCC Certification of this device and may cause
interference levels which exceed the limits established by the FCC for this equipment. It is
the responsibility of the user to obtain and use a shielded equipment interface cable and a
shielded power cable with this device. If this equipment has more than one interface
connector, do not leave cables connected to unused interfaces.
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
FOR CANADIAN USERS
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the radio interference regulations of the Canadian
Department of Communications.
Le present appareil numkique n’6met pas de bruits radio&lectriques d&passant les limites
applicables aux appareils numkiques de Classe B prescrites dans le rkglement sur le
brouillage radio&lectrique Bdict& par le Ministkre des Communications du Canada.

IMPORTANT NOTICE
DISCLAIMER OF WARRANTY
Epson America makes no representations or warranties, either express or implied, by or
with respect to anything in this manual, and shall not be liable for any implied warranties
ofmerchantability and fitness for a particular purpose or for any indirect, special, or
consequential damages. Some states do not allow the exclusion of incidental or
consequential damages, so this exclusion may not apply to you.
COPY RlGHT NOTlCE
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Epson
America, Inc. No patent liability is assumed with respect to the use of information
contained herein. Nor is any liability assumed for damages resulting from the use of the
information contained herein. Further, this publication and features described herein are
subject to change without notice.
TRADEMARKS
EPSON is a registered trademark of Seiko Epson Corporation
EPSON Connection is a service mark of Epson America, Inc
General notice: Other product names used herein are for identification purposes only and
may be trademarks of their respective companies.
The Energy Star emblem does not represent EPA endorsement of my product or service.
Copyright © 1994 by Epson America, Inc
Torrance, California
400385600
l0/ 94
ii

Important Safety Instructions
Although this monitor is designed to assure your safety, improper use
can cause electric shock or fire hazard. In order not to defeat the
safeguards incorporated in the monitor, observe the following safety
instructions:
1. Read all of these instructions and save them for later reference
2. Follow all warnings and instructions in this manual and marked
on the monitor.
3. The monitor contains shock hazard potential. Do not attempt to open
or remove any covers, and do not attempt to service the monitor
yourself. Refer all servicing to authorized service personnel.
4. Never push objects of any kind into the monitor through cabinet slots.
5. Do not expose the monitor to liquids, such as rain or spills
6. Do not place the monitor on an unstable cart, stand, or table, and be
careful not to drop it.
7. Do not place the monitor near a heating appliance or in direct sunlight.
Intense heat can damage the monitor’s circuitry.
8. Slots and openings on the top, bottom, and back of the cabinet are
provided for ventilation; do not block or cover these openings. Do
not place the monitor in a built-in insulator, such as a bookcase,
unless proper ventilation is provided.
9. Power supply voltages outside the monitor’s specified line voltage
range may harm the monitor. The monitor should be operated from
the type of power source indicated on the rear panel label.
10. Make sure the combined amperage rating for all products plugged
into the wall outlet used for the monitor does not exceed the
amperage rating of the wall outlet.
11. Use only the power cord supplied with the monitor. If you must use
another power cord, make sure it meets the applicable standards
(UL/ CSA or VDE).
iii

12. Do not overload the inlet and extension cords as this can result in fire
or electric shock.
13. Be careful not to damage the power cord or plug.
14 Do not allow anything to rest on the power cord. Do not place a cord
where it may be stepped on.
15. Do not replace the video interface cable with a non-shielded cable.
16. Unplug the monitor from the wall outlet and the computer before
cleaning. Use a damp cloth for cleaning.
17. Excessive brightness for long periods may permanently imprint an
image on the screen.
18. To avoid picture distortion or color disturbance, do not put devices
that generate magnetism (such as telephones, televisions, speakers,
or magnetic screwdrivers) near the monitor.
19. When you finish using the monitor, turn it off by pressing the power
button. (Always wait at least five seconds before you turn it back
on.) When the monitor will not be used for a long period of time,
unplug the power cord.
20. Unplug the monitor from the wall outlet and refer servicing to
authorized service personnel under the following conditions:
A. If the power cord or plug is damaged
B. If the monitor has come into contact with any liquids, such as rain
or spills.
C. If the monitor does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions; improper adjustment of
other controls may result in damage and will often require
extensive work by a qualified technician to restore the product
to normal operation.
D. If the monitor has been dropped or the cabinet or glass faceplate
has been damaged.
E. If the monitor exhibits a distinct change in performance.
iv

Importantes mesures de securite
Bien que le moniteur soit concu pour assurer votre securite, un usage
incorrect peut provoquer une decharge lectrique ou poser un risque
d’incendie. Pour ne pas aller a l’encontre des mesures de protection
incorporees dans le moniteur, veuillez bien observer les instructions
suivantes:
1.
2.
3.
4.
5.
6.
Lire attentivement les instructions qui suivent. Les conserver en lieu
stir.
Observer les avertissements marques sur le moniteur et suivre
rigoureusement les instructions contenues dans le manuel.
Le moniteur pose des risques de decharge Clectrique. Ne pas
tenter de soulever ou d’enlever les couvercles; ne pas essayer de
reparer le moniteur soi-meme; s’adresser au personnel de service
autorise par le fabricant.
Ne jamais rien introduire dans les ouvertures du coffre.
Proteger le moniteur de tout contact avec l’eau, la pluie, les boissons
renversees, etc.
Ne pas laisser tomber l’appareil. kviter de le placer sur un meuble
instable.
Ne pas placer le moniteur a proximite d’un appareil de chauffage, ni
en plein soleil. La chaleur intense peut endommager les circuits.
11 est important de ne pas bloquer les ouvertures sit&es sur le dessus,
le dessous et a l’arriere de l’appareil: ce sont des prises d’air qui en
assurent la ventilation. k moins d’assurer une circulation d’air
adequate, ne pas placer le moniteur dans un espace restreint comme
une bibliotheque, par exemple.
Un voltage inferieur ou superieur a celui qui est specifiquement
designe pour le moniteur pourrait l’endommager. Utiliser
seulement la source d’electricite indiquee sur l’etiquette du panneau
arriere.
V

10. L’amperage total de toutes les pieces branchees sur le meme socle ne
doit pas depasser la capacite en amperes du socle.
11. Utiliser seutement le cordon Clectrique dont le moniteur est muni. S’il
est necessaire de se servir d’un autre cordon, s’assurer que les
standards de fabrication sont conformes aux reglements en vigueur
(UL/ CSA ou VDE).
12. Ne pas surcharger la prise de courant et les cordons allonge car cela
pourrait provoquer une decharge Clectrique ou poser un risque
d’incendie.
13. Faire attention a ne pas abimer le cordon Clectrique ni la prise de
courant.
14. Ne rien laisser reposer sur le cordon electrique. Ne pas placer de
cordon de maniere a ce qu’on risque de marcher dessus.
15. Ne pas remplacer un cordon d’interface video par un cordon non
protege.
16. Debrancher le moniteur du socle et de l’ordinateur avant de le
nettoyer. Utiliser seulement un chiffon humide.
17. Si la luminosite de l’ecran reste a sa plus haute intensite pendant de
longues periodes, l’image pourrait y rester imprimee de facon
permanente.
18. Pour Cviter les deformations de l’image ou les perturbations de
couleur, ne pas placer de sources de magnetisme telles que
telephones, postes de television, haut-parleurs ou tournevis
magnetiques a proximite du moniteur.
19. Apres s’etre set-vi du moniteur, l’eteindre en pressant l’interrupteur.
Toujours attendre au moins cinq secondes avant de le remettre en
marche. Debrancher le moniteur lorsqu’on ne devra pas l’utiliser
pendant de longues periodes.
20. Debrancher le moniteur et s’adresser au personnel de service autorise
dans les conditions suivantes:
A. Si le cordon est effiloche ou la prise est endommagee.
vi

B. Si le moniteur est entre en contact avec des liquides comme la
pluie ou des boissons renversees.
C. Si le moniteur ne repond pas normalement aux commandes
pas&es en suivant les instructions. Ajuster uniquement les
controles decrits dans les instructions; il est possible de
gravement endommager l’appareil en touchant les autres, ce qui
pourrait necessiter l’intervention d’un technicien qualifie pour
le remettre en Ctat de marche.
D. Si le moniteur est tombe, ou si l’ecran ou le coffre ont CtC
endommages.
E. Si la performance du moniteur est nettement differente de
l’ordinaire.
vii

Contents
Introduction ....................
Energy Star Compliance
...........
Where to Get Help
..............
CompuServe On-line Support .......
Unpacking the Monitor ..............
Setting Up the Monitor ..............
Attaching the Tilt and Swivel Base .....
Selecting a Location for the Monitor ....
Connecting the Monitor to Your Computer
Turning On the Monitor .............
Accessing the Monitor Controls .........
Adjusting Monitor Controls .........
How Video Modes Work .............
Adjusting the Screen Image
.........
Cleaning the Monitor ...............
Troubleshooting ..................
Specifications
....................
CRT.. .....................
Display .....................
Interfacing Requirements ...........
AC Line Voltage ................
Display Power Management .........
Environmental Requirements ........
Predefined Video Modes ...........
Safety Standards
................
Digitally Adjustable Screen Parameters
Other Controls .................
Physical Characteristics
............
1
2
2
3
3
4
5
7
7
9
10
11
14
16
17
18
21
21
21
22
24
24
24
25
25
25
25
26
ix

lntroduction
Your EPSON®Super VGA color monitor is a high-performance,
multifrequency, autoscan monitor for use with graphic video
controllers. It offers the following features:
17-inch, flat-square, analog color CRT display with non-glare
picture tube
High-resolution display of up to 1280 x 1024 pixels at a fast,
stable refresh rate (vertical frequency) of up to 60 Hz
Automatic scanning of all horizontal frequencies from 30 to
65.8 KHz and all vertical frequencies from 50 to 120 Hz
Seven predefined IBM®or VESA compatible video modes,
including two at VGA 640 x 480, two at Super VGA
1280 x 1024, plus one each at VGA 640 x 400, Super VGA
800 x 600, and Super VGA 1024 x 768
In addition to the seven predefined video modes, the
programmable microprocessor memory allows the monitor to
create up to five user-defined video modes, if necessary
The following six screen parameters settings are adjustable
with digital buttons at the front of the monitor: horizontal and
vertical position, width, height, side pin cushion, and trapezoid
Digital DEGUSS button, for demagnetizing the CRT
Three video sync formats: separate horizontal and vertical
sync, composite horizontal and vertical sync, or composite
horizontal and vertical sync on green (low-power mode)
A universal power supply which automatically adjusts to
different AC voltage sources
Low radiation and compliance with the latest Swedish
magnetic emissions guidelines (MPRII).
17” Super VGA Color Monitor 1

This manual provides instructions on how to set up and use the
monitor. It describes how to adjust the monitor controls and the
screen parameter settings. It also provides troubleshooting
information and specifications.
Energy Star Compliance
The EPSON monitor complies with the U.S. Environmental
Protection Agency’s Energy Star program, which promotes the
manufacture of energy-efficient printers, computers, and monitors.
If your computer is Energy Star compliant, the EPSON Super VGA
color monitor automatically enters a low -power standby mode
when the computer stops sending video signals to the monitor.
The power indicator at the front right of the monitor is amber
when the monitor is in this low-power mode.
The EPA estimates that if all desktop computers, monitors,
printers, and other peripheral devices met Energy Star standards,
energy cost savings would exceed $1 billion annually and carbon
monoxide emissions would be reduced by 20 million tons.
Where to Get Help
If you purchased your monitor in the United States or Canada,
EPSON provides support services through the EPSON
Connection.
sm
In the United States, dial [phone]. In Canada,
dial (800) GO-EPSON.
Call the EPSON Connection for the following:
0 Technical assistance with the installation, configuration, and
operation of EPSON products
0 Assistance in locating your nearest Authorized EPSON
Reseller or Customer Care Center
2 17” Super VGA Color Monitor

0 Sales of ribbons, supplies, parts, documentation, and
accessories for your EPSON product
0 Customer Relations
0 EPSON technical information and library fax service
0 Product literature with technical specifications on our current
and new EPSON products.
If you purchased your monitor outside the United States, contact
an authorized EPSON reseller for support and service.
International marketing locations are listed inside the back cover
of this manual.
CompuServe On-line Support
If you have a modem, the fastest way to access helpful tips,
specifications, drivers application notes, tables for DIP switch or
jumper settings, and bulletins for EPSON products is through the
Epson America Forum on CompuServe.®
If you are already a CompuServe member, simply type GO EPSON
at the menu prompt to reach the Epson America Forum.
Unpacking the Monitor
When you unpack your monitor, make sure you have the
following items:
0 EPSON 17” Super VGA color monitor (tilt and swivel base
may be attached)
0 Video interface cable [(to connect the monitor to the computer
(for IBM/ VGA compatibles only)]
0 AC power cord (to connect the monitor to a wall outlet)
17” Super VGA Color Monitor 3

0 Warranty card
0 Registration card.
Complete the registration card and return it to EPSON so you’ll
receive update information. Keep the warranty card for your
records.
If anything is missing or damaged, contact your EPSON
representative immediately.
Note
Be sure to keep the monitor’s original box and packing
materials in case you need to transport the monitor later.
Setting Up the Monitor
This section describes how to attach the tilt and swivel base (if it is
not already attached), select a location for the monitor, and
connect the monitor to your computer.
4 17” Super VGA Color Monitor

Attaching the Tilt and Swivel Base
Before you attach the tilt and swivel base, cover your work area
with a blanket or foam pad to avoid scratching the monitor during
assembly. Then follow these steps:
1. Carefully set the monitor face down on the padding so the
bottom of the monitor is facing you, as shown below.
latches
dots
2. Locate the four sets of hooks and the latches on the top portion
of the tilt and swivel base, as shown above.
17” Super VGA Color Monitor 5

3. Hold the base so that the hooks are pointed down. Then position
the base next to the bottom of the monitor, as shown below.
4. Insert the hooks on the base into the slots on the monitor.
5. Slide the base down toward the front of the monitor until the
latch clicks into the locked position. Then turn the monitor
upright so it rests on its base.
Note
Always remove the tilt and swivel base before packing and
transporting the monitor. To remove the base, disconnect the
power cord from the electrical outlet and disconnect the cables
from the back of the monitor. Carefully set the monitor face
down on a padded surface. While pressing the release tab on
the bottom of the monitor, remove the base by lifting the hooks
out of the slots.
617” Super VGA Color Monitor

Selecting a Location for the Monitor
Follow these guidelines when you select a location for the monitor:
Follow the safety instructions listed at the beginning of this
manual.
Use a large, sturdy desk that can support the weight of your
computer, monitor, and peripheral devices and provides
ample space to hold your equipment and work materials.
For your comfort, it is best to place the monitor directly in
front of you and sit about an arm’s length away from it.
To minimize glare and reduce eye fatigue, position the
monitor so that sunlight, desk lamps, or overhead lights do
not shine directly on the screen.
For comfortable viewing, the top of the screen should be
slightly below eye level when you are sitting in front of the
monitor. Your line of sight to the screen should be about 10° to
20° below eye level.
Connecting the Monitor to Your Computer
Before you connect the monitor to your computer, make sure your
computer and video adapter are set up to use with the monitor. If
necessary, install an appropriate video adapter card in your
computer and set any DIP switches or jumpers on the card to
support the monitor. You may also need to change jumper settings
inside the computer. See your computer or video adapter card
manual for instructions.
Follow these steps to connect the monitor to your computer:
1. Before you connect any cables, make sure the monitor,
computer, and all other peripheral devices are turned off.
17” Super VGA Color Monitor 7

2. Turn the monitor around so you are looking at the back, as
shown below.
AC power inlet D-sub VGA connector
3. Locate the connector cable and the power cord that came with
the monitor.
4. Plug one end of the video interface cable monitor into the
monitor’s D-sub VGA connector. Tighten the screws on the
cable connector.
5. Plug the other end of the video interface cable into the D-sub
VGA connector on the back of your computer. Then tighten
the two screws on the connector cable. (See your computer or
video adapter card manual for more detailed instructions.)
6. Plug the monitor’s power cord into the AC power inlet on
the back of the monitor.
7. Plug the other end of the power cord into a properly grounded
electrical outlet.
Note
The monitor contains a universal power supply, so you can
connect it to any power supply in the range of 100 to
260 VAC with a 50 to 60 Hz line frequency.
817” Super VGA Color Monitor

8. Turn the monitor around so the screen faces you and use the tilt
and swivel base to adjust the position of the screen for
comfortable viewing.
Note
You can also connect your monitor to an Apple®Macintosh®
computer using an appropriate cable and/or adapter. Purchase
these items at a computer accessory store.
Turning On the Monitor
Turn on the monitor by pressing the power button located at the
front right of the monitor, as shown below. The monitor’s power
indicator lights up. Now turn on the computer. After a few
seconds, an image appears on the screen. To make the image on
the screen clear and easy to read, use the brightness and contrast
controls in the image control box (see the next section).
.
screen
parameier
Aage
control box
. . . . . . “war
- -
Upoweromoff
button
contrast
brightness
power
indicator
control control
17” Super VGA Color Monitor 9

The power indicator light is green when the monitor is drawing
full power. When the monitor is in low-power mode, the power
indicator is amber.
Accessing the Monitor Controls
The image control box contains the image controls for the monitor.
It is located at the bottom left of the monitor. To access the
controls, you need to open the control box cover. Place your finger
on the raised dots at the center of the cover and push in until you
hear the cover latch click. Release your finger to pull down the
cover.
10 17” Super VGA Color Monitor

Adjusting Monitor Controls
The controls and indicators in the control box are shown below.
klkllHl~~ o+y~o
lxJoelol3n
SELECT DOWN UP
DEGAUSS
The following table describes the monitor controls, including the
digital adjustment buttons, the brightness and contrast dials, and
the six available screen parameter settings that adjust the screen
image. Each screen parameter setting is marked by an indicator
light and corresponding icon.
Monitorcontrols
Monitor control Function
SELECTbutton Selectsa screen parameterto adjust. To select a
screen parameter, repeatedly push the SELECT
0
button until the LED forthe parameteryou want lights.
LEDsare lit from left to right acrossthe panel. Once lit
up, you can adjust the screen parameterusing the
UPand DOWN buttons. Your changes are
SELECT
automatically saved asyou make them. The default
setting isoff.
DOWN button Decreasesthe value ofa selected screen parameter
v
in digital increments.
DOWN
UP button Increasesthe value of the selected screen parameter
A
in digital increments.
UP
17” Super VGA Color Monitor
11