Epson EPL-N2500 Installation instructions

Safety Instructions
Laser Printer Precautions
This printer uses laser technology. Follow the precautions below to ensure
safe, efficient operation.
❏Unless specifically instructed in the
printer’s documentation, be careful not
to touch the fuser, which is marked
CAUTION HOT SURFACE. If the printer has
been in use, the fuser may be very hot.
❏Do not attempt to modify or take the
imaging cartridge apart. It cannot be
refilled.
❏Do not touch the toner and avoid all
toner contact with your eyes.
❏Do not dispose of used imaging
cartridges in fire, as it can explode and
cause injury. Dispose of it according to
local regulations.
Important Safety Instructions
Read all of the following instructions before operating your printer:
When choosing a place for the printer
❏Do not place the printer on an unstable surface.
❏Do not put your printer where the cord will be stepped on.
❏Slots and openings in the cabinet and the back or bottom are
provided for ventilation. Do not block or cover them. Do not put the
printer on a bed, sofa, rug, or other similar surface or in a built-in
installation unless proper ventilation is provided.
When choosing a power source
❏The interface connector for this printer, excluding the USB connector,
is Non-LPS (non-limited power source).
CAUTION
HOT SURFACE
Copyright©2003 by SEIKO EPSON CORPORATION, Nagano, Japan
Printed in xxxxx 03.xx-xx 4041286-00 xxx

2
❏Avoid using outlets that other appliances are plugged into.
❏Use the type of power source indicated on the label. If you are not
sure of the type of power available, consult your dealer or local
power company.
❏If you are unable to insert the plug into the outlet, contact a qualified
electrician.
❏If you use an extension cord, make sure that the total of the ampere
ratings on the products plugged into the extension cord does not
exceed the extension cord ampere rating.
❏Unplug this printer from the wall outlet and refer servicing to a
qualified service representative under the following conditions:
When using the printer
❏The printer weighs about 19.5 kg (43 lb). One person should not
attempt to lift or carry the printer. Two people should carry it.
❏Follow all warnings and instructions marked on the printer.
❏Unplug this printer from the wall outlet before cleaning.
❏Use a well-wrung cloth for cleaning and do not use liquid or aerosol
cleaners.
❏Avoid touching the components inside the printer unless instructed
to do so in the printer’s documentation.
❏Never force printer components into place. Although the printer is
designed to be sturdy, rough handling can damage it.
❏Be sure to keep consumables out of the reach of children.
❏Do not use this printer near water.
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into it.
C. If it has been exposed to rain or water.
D. If it does not operate normally when the operating instructions are followed.
Adjust only those controls that are covered by the operating instructions
since improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product
to normal operation.
E. If it has been dropped or the cabinet has been damaged.
F. If it exhibits a distinct change in performance, indicating a need for service.

3
❏Do not leave jammed paper inside of the printer. This can cause the
printer to overheat.
❏Never push objects of any kind through cabinet slots as they may
touch dangerous voltage points or short out parts that could result
in a risk of fire or electric shock.
❏Never spill liquid of any kind on the printer.
❏Except as specifically explained in the printer’s documentation, do
not attempt to service this product yourself. Opening or removing
those covers that are marked Do Not Remove may expose you to
dangerous voltage points or other risks. Refer all servicing in those
compartments to a qualified service representative.
❏Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in
damage and may require repair by a qualified service
representative.
Safety Information
Power cord
cCaution:
Be sure the AC power cord meets the relevant local safety standards.
Use only the power cord that comes with this product. Use of the another
cord may result in fire or electric shock.
This product’s power cord is for use with this product only. Use with other
equipment may result in fire or electric shock.
Laser safety labels
wWarning:
The performance of procedures and adjustments other than those
specified in the printer’s documentation may result in hazardous
radiation exposure.
Your printer is a Class 1 laser product as
defined in the IEC60825 specifications. The
label shown is attached to the back of the
printer in countries where required.

4
Internal laser radiation
This is a Class III b Laser Diode Assembly that has an invisible laser beam.
The printer head unit is NOT A SERVICE ITEM, therefore, the printer head unit
should not be opened under any circumstances. An additional laser
warning label is affixed to the inside of the printer.
Ozone safety
Ozone emission
Ozone gas is generated by laser printers as a by-product of the printing
process. Ozone is produced only when the printer is printing.
Ozone exposure limit
The recommended exposure limit for ozone is 0.1 parts per million (ppm)
expressed as an average time-weighted concentration over an eight (8)
hour period.
The EPSON laser printer generates less than 0.1 ppm for eight (8) hours of
continuous printing.
Minimize the risk
To minimize the risk of exposure to ozone, you should avoid the following
conditions:
❏Use of multiple laser printers in a confined area
❏Operation in conditions of extremely low humidity
❏Poor room ventilation
❏Long, continuous printing together with any of the above
Printer location
The printer should be located so that the exhaust gases and heat
generated are:
❏Not blown directly into the user’s face
❏Vented directly out of the building whenever possible
Max. Average Radiation Power: 5 mW at laser aperture
Wavelength: 770 to 800 nm