Epson Stylus C63 User manual

Continuous Ink Supply System
for
Epson Stylus C63/C65/C84/C86 Printer
Installation Instruction
For MT Empty Cartridge Version
With Auto Reset Chips
CIS for Epson C63/C65/C84/C86 Instruction
I. What’s in the MT-C63 Continuous Ink Supply system?
1) 4 * 100ml Reservoir Bottles;
2) Tubing Attached with Cartridge and Chips;
3) A set of Support Arm & Black Rubber;
4) 4 * Vacuum Pump (Filling tools).

READ ALL INSTRUCTION PRIOR TO INSTALLING YOUR NEW SYSTEM
Thank you for purchasing MT Continuous Ink Supply System. We appreciate your
support and will try our best to make your experience with our products a pleasant one.
Printing has been a different experience ever since you installed MT Continuous Ink
Supply system on your own printer. Just imagining being able to print without regard to
the ink level in those expensive little cartridges.
Please take your time installing MT Continuous Ink Supply system. Do not remove your
old cartridge until you have the MT CIS system primed and ready to install (to prevent
the drying of heads). In addition, make sure you are getting perfect nozzle checks
before installing the MT CIS system. The MT CIS system won’t be able to work properly
if the nozzles are previously clogged.
Most people get a perfect nozzle check the first time after installing the MT Continuous
Ink Supply system; others may need to run two or three cleaning cycles or let the printer
sit for a while before they get the perfect results.
II. Getting Started
1. Check the printer head before beginning the installation.
1) Open the window of the Computer and find the Control Panel. Then click
“Printer and Other Hardware”
2) Click the right button of mouse on EPSON Stylus C63 Series. Then click the
Properties and choose the “Nozzle Check” as the below picture shown.

3) Using the EPSON Utility, print a “ Nozzle Check” to make sure that all the nozzles
are firing properly.
2. Press the “ink cartridge replace button” (Picture A) on the printer to move the cartridge
to the cartridge remove position (Picture B).

(Picture A) (Picture B)
3. Unplug the power connector at the back of the printer (Picture A). This will prevent the
printer from “auto powering down”, allowing you have as much time as you need to
complete the installation. Remove the cartridges as the below picture B shown.
Then use a small screwdriver to remove the original cover (Picture C)
(Picture A). (Picture B) (Picture C)
4. Open the black cap of the Reservoir bottle and fill ink into it one by one; please pay
attention to the color sticker on the Reservoir Bottles and fill ink according to the
sticker’s color.
1) Pay attention to the direction guide on the Black cap and direction guide on the
Bottles, when the printer is working, make sure the two direction guides are on
the horizontal line to let the air in. In the case of leaking out ink, make them on the
vertical line when the printer stops working.

Stopping Working
2) Roll up the Plastic Valve.
5. Firstly use a needle to poke the film of the cartridge (Picture A); Then insert the vacuum
pump into the holes of Cartridge as the below picture shown and pull the plunger
backward (Picture B); Stop pulling the plunger till ink flows into the vacuum pump;
(Picture A) (Picture B)
6. Measure 13cm from the edge of the printer and make a mark: then tear off the sticker
(Picture A) and attach Support Arm to the printer as the Picture B shows.

(Picture A) (Picture B)
7. Attach the small tube clamp at the right of the printer and Make sure it is parallel with the
Support Arm as the below picture shown.
8. Insert the cartridge into the cartridge carriage after finishing ink-filling; Make sure the
cartridge is down all the way and they are making contact with the fingers that read
chips;
9. Put the Tube into the Support Arm and Small Tube clamp as the below picture shown.

10. Slide the cartridge back and forth from left to right several times; make sure the tubes
not too tight when cartridge is in the far right and left position.
Now everything is put together! Double check your cartridge; then turn on the
power. Watch for anything unusual. You are ready to start printing.
III. Nozzle Check
11. Turn on the power and clean the printer head for two or three times as the following
picture shown.
12. Print the test paper and if the print effect shown as the following picture, you can start
printing.

IV. Auto Reset Procedure
13. When the indicator light on printer shows short of ink and change cartridges (Picture
A); Please turn off the printer for about 30 seconds, then switch it back on. At this
time the Ink meter bar shall show 99% (Picture B). You can start printing as usual.
(Picture A) (Picture B)
P.S: the black rubber is used only in the process of transportation when the reservoir bottles
are full of ink. They are used to avoid ink leakage. In the meantime, you can use it for
propping up the lid of the printer
Notice:
1. Please don’t take out cartridge at random after installing the CIS system. Keep the reservoir
bottles on the same level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles, as you don’t want to run out of ink and draw
air into the cartridge.
3. Don’t place the Reservoir Bottles higher or lower much than the printer.
4. To be used in a dry place between 15 and 35degree. Avoid exposure to direct sunlight.
5. Don’t put the continuous ink supply systems reversed or leaning during the shipment.
Please make sure all the ink filling holes and Ventilation holes are closed tightly during the
transportation. Otherwise, the ink shall leak out.
6. Don’t sway the cartridge frequently. It may cause ink leakage.
7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the bottom of
cartridge.
Warning:
1. Not drinkable; keep it out reach of children.
2. Avoid exposure to direct sunshine and don’t keep it in high or freezing temperature.
3. Avoid collision and fallen down.