Epson SureColor S40600 User manual

Contents
Unpacking and assembling the printer .............................................................................................. 2
Assembling the stand .................................................................................................................. 5
Installing the printer ................................................................................................................... 8
Installing the auto take-up reel unit ..........................................................................................14
Installing the media feeding unit ..............................................................................................18
Connecting the cables .............................................................................................................. 21
Installing the print drying system (included with SC-S60600) ................................................. 25
Installing ink cartridges ................................................................................................................... 26
Installing the software ..................................................................................................................... 28
Setting an administrative password ........................................................................................... 29

2|Unpacking and assembling the printer
Unpacking and assembling the printer
Note: Unless otherwise indicated, the illustrations in this manual show the SureColor®S40600, but the
instructions apply to all models.
Before you begin, make sure you have enough space to set up and use the printer. When choosing a place
for the printer, select a location that provides easy access to the printer and is within the printer’s operating
conditions (59 to 95 °F [15 to 35 °C]; 20 to 80% humidity without condensation). The following
illustration shows the minimum space required to use the printer:
Caution: Avoid locations subject to direct sunlight, excessive heat, moisture, smoke, dust, sand, or vibrations
from other equipment. Do not tilt the printer more than 10° while moving it.
WARNING: Eight people are required to unpack and install the printer. Be sure the printer is placed on a flat,
stable location that is well ventilated and can support the following weight and power requirements for each
printer:
•SC-S40600 — 615 lb (279 kg); access to one or more outlets for 2 power cables with a total amperage
of 20 A at 100 V or 10 A at 240 V
•SC-S60600 — 641 lb (291 kg); access to one or more outlets for 3 power cables with a total amperage
of 21 A at 100 V or 10.5 A at 240 V
•SC-S80600 — 626 lb (284 kg); access to one or more outlets for 2 power cables with a total amperage
of 20 A at 100 V or 10 A at 240 V
145.5 in.
(362 cm)
39.4 in.
(100 cm)
69.7 in.
(177 cm)
107.9 in.
(274 cm)
19.7 in.
(50 cm)
19.7 in.
(50 cm)
3.9 in.
(10 cm)
39.4 in.
(100 cm)

Unpacking and assembling the printer |3
The following items are included:
Printer and stand
:

4|Unpacking and assembling the printer
Auto take-up reel and media feeding unit
:
Print drying system (included with SC-S60600)
Maintenance supplies
Note: The maintenance supplies are not required for setup. For more information on their use, see the Quick
Reference or online User’s Guide.
After unpacking the printer and stand, save the box and packaging in case you need to ship the printer
later.

Assembling the stand |5
Assembling the stand
You need the following parts to assemble the stand:
Note: It is recommended to have 3 or more people assemble the stand.
1. Slide the larger horizontal strut into both of the legs.
2. Use the long end of the hex wrench to tighten the pre-placed screws on each side of the horizontal
strut.

6|Assembling the stand
3. Slide in both of the smaller horizontal struts.
4. Use the hex wrench to tighten the screw on each of the four corners.
5. Attach the waste ink tank bracket to the right side of the stand and secure it using a Bscrew.

Assembling the stand |7
6. Slide up the adjustable securing plate (shaded part in step 1 below) and secure the waste ink tank
bracket to it using two B screws. Attach the other waste ink tank bracket and secure it using a B screw.
7. Insert the three cable support clips into the holes shown.

8|Installing the printer
Installing the printer
You need the following parts to install the printer on the stand:
1. Lock the casters on the stand to prevent it from moving.
2. Lift up the latch securing the carry bars and remove the carry bars from the back of the printer.

Installing the printer |9
3. From the front of the printer, insert the carry bars into both sides with the locking bolts toward the
side as shown. Once they are inserted, rotate the bars counterclockwise 90° to lock them into place.
This prevents the printer from sliding when lifted.
WARNING: Use at least eight people to carry the printer as shown.
Note: To avoid stepping on the crate underneath the printer, try to place the printer adjacent to the stand
before lifting the printer.

10 |Installing the printer
4. Lift the printer onto the stand. Make sure to line up the bottom of the printer with the top of the
stand as shown.
5. Remove the carry bars.
6. Secure the printer to the stand using eight Ascrews and washers.