Epson TM-U220 Series User manual

User’s Manual / Manuel d’utilisation
Bedienungsanleitung / Gebruikershandleiding
Manuale dell’utente / Manual del usuario
Manual do utilizador / KullanıcıKılavuzu
Navodila za uporabo / Korisnički priručnik
Brugervejledning / Käyttöohje
Brukermanual / Bruksanvisning
Uživatelská příručka / Felhasználói kézikönyv
Руководство по эксплуатации
Пайдаланушы нұсқаулығы
/ 사용자 매뉴얼
M00085301

ii
Type A Type B Type D
2
1
34
A
BC
DE

iii
F G
HG-a
IJ

iv
KL
MN
OP

v
Features of Printer Types
See illustration A.
DIP Switch Tables
US (for Type A printer)
Type A Type B Type D
Autocutter Yes Yes No
Take up device Yes No No
Paper width (mm) 76 76/69.5/57.5 76/69.5/57.5
Look at the numbers and letters in the area
indicated in the illustration. If the last
letters are “US”, use the “US” tables
below. If the last letters are “STD”, use the
“STD” tables.
CAUTION:
Be sure to replace the DIP switch cover
before using the printer.
Serial (DIP Switch 1)
SW Function On Off
1 Data receive error Ignored Prints “?”
2 Receive buffer capacity 40 bytes 4 KB
3 Handshaking XON/XOFF DTR/DSR
4 Word length 7 bits 8 bits
5 Parity check Yes No
6 Parity selection Even Odd
7 Transmission speed 4800 bps 9600 bps
8BUSY condition Receive buffer full Receive buffer full
or Offline
Serial (DIP Switch 2)
SW Function On Off
1 Print column 42/35 40/33
2 For internal use only
(autocutter) Enabled Disabled
3Pin 6 reset signal Used Not used
4Pin 25 reset signal Used Not used
5 Undefined - -
6 For internal use only
(flash memory rewriting) Enabled Disabled
7 Undefined - -
8 Serial interface selection Memory
switch DIP switch
Parallel (DIP Switch 1)
SW Function On Off
1 Auto line feed Enabled Disabled
2 Receive buffer
capacity 40 bytes 4 KB
3~7 Undefined - -
8 BUSY condition Receive
buffer full Receive buffer full or
Offline
Parallel (DIP Switch 2)
SW Function On Off
1 Print column selection 42/35 40/33
2 For internal use only
(autocutter) Enabled Disabled
3 Undefined - -
4 Pin 31 reset signal Used Not used
5 Undefined - -
6 For internal use only
(flash memory rewriting) Enabled Disabled
7 Undefined - -
8 Undefined - -

vi
US (for Type B and Type D printer)
*: If you set DIP Switch 1-1 to On (Right side up printing mode), make sure to set DIP Switch 1-2 to Off
(Receive buffer capacity: 4 KB).
Serial (DIP Switch 1)
SW Function On Off
1 Printing mode Right side up
printing
mode
Normal
printing
mode
2 Receive buffer capacity 40 bytes 4 KB
3 Handshaking XON/XOFF DTR/DSR
4 Word length 7 bits 8 bits
5 Parity check Yes No
6 Parity selection Even Odd
7 Transmission speed 4800 bps 9600 bps
8BUSY condition Receive buffer full Receive buffer full
or Offline
Serial (DIP Switch 2)
SW Function On Off
1 Print column 42/35 40/33
2 For internal use only
(autocutter) Enabled Disabled
3Pin 6 reset signal Used Not used
4Pin 25 reset signal Used Not used
5 Undefined - -
6 For internal use only
(flash memory rewriting) Enabled Disabled
7 Undefined - -
8 Serial interface selection Memory
switch DIP switch
Parallel (DIP Switch 1)
SW Function On Off
1 Printing mode Right side up
printing
mode
Normal
printing
mode
2 Receive buffer
capacity 40 bytes 4 KB
3~7 Undefined - -
8 BUSY condition Receive
buffer full Receive buffer full or
Offline
Parallel (DIP Switch 2)
SW Function On Off
1 Print column selection 42/35 40/33
2 For internal use only
(autocutter) Enabled Disabled
3 Undefined - -
4 Pin 31 reset signal Used Not used
5 Undefined - -
6 For internal use only
(flash memory rewriting) Enabled Disabled
7 Undefined - -
8 Undefined - -

vii
STD
Serial (DIP Switch 1)
SW Function On Off
1 Data receive error Ignored Prints “?”
2 Receive buffer capacity 40 bytes 4 KB
3 Handshaking XON/XOFF DTR/DSR
4 Word length 7 bits 8 bits
5 Parity check Yes No
6 Parity selection Even Odd
7 Transmission speed 4800 bps 9600 bps
8BUSY condition Receive buffer full Receive bufferfullor
Offline
Serial (DIP Switch 2)
SW Function On Off
1 Print column 42/35 40/33
2 For internal use only
(autocutter) Enabled Disabled
3 Undefined - -
4 Serial interface selection Memory
switch DIP switch
5 Undefined - -
6 For internal use only
(flash memory rewriting) Enabled Disabled
7 Pin 6 reset signal Used Not used
8 Pin 25 reset signal Used Not used
Parallel (DIP Switch 1)
SW Function On Off
1 Auto line feed Enabled Disabled
2 Receive buffer capacity 40 bytes 4 KB
3~7 Undefined - -
8 BUSY condition Receive
buffer full Receive bufferfullor
Offline
Parallel (DIP Switch 2)
SW Function On Off
1 Print column selection 42/35 40/33
2 For internal use only
(autocutter) Enabled Disabled
3~5 Undefined - -
6 For internal use only
(flash memory rewriting) Enabled Disabled
7 Undefined - -
8 Pin 31 reset signal Used Not used

viii
TM-U220 Specifications
dpi: dots per 25.4 mm (dots per inch); lps: lines per second; lpi: lines per 25.4 mm (lines per inch)
*1: Be sure to use a safety-standards-applied power source that meets the following specifications.
Rated output: 24 V/2.0 A or more, Maximum output: 240 VA or less
Printing method 9-pin serial impact dot matrix method
Print font Font (standard) Font A: 7 × 9, Font B: 9 × 9
Column capacity
(columns)
7 × 9/9 × 9:
76 mm: 40/33
69.5 mm: 36/30
57.5 mm: 30/25
Character size (W ×H)
(standard)
1.2 × 3.1 mm/1.6 × 3.1 mm (not including horizontal
spacing)
Character set 95 Alphanumeric, 48 International,128 × 12 Graphic
Characters per inch
(standard)
(3 half dot spacing)
Font A (7 × 9): 16 cpi, Font B (9 × 9): 13.3 cpi
Paper Dimensions (mm) 57.5 ±0.5, 69.5 ±0.5,
76 ±0.5
Normal paper (mm) Thickness:
0.06~0.085 (1 sheet)
Pressure-sensetive
paper
Thickness: 0.05~0.08 (1 sheet), total thickness must be
0.14 mm or less.
Number of copies: Original 1 sheet + one copy sheet
Ribbon cassettes ERC-38 (B) Black life: 3,000,000 characters
ERC-38 (B/R) Black/Red life: Black 1,500,000/Red
750,000 characters
Life based on continuous printing at 25°C {77°F}
Printing speed (Paper width 76 mm) 4.7 lps (40 columns, 16 cpi)
Interface RS-232 or IEEE 1284
Receive buffer 4 KB or 40 bytes
Power supply*1 24 VDC ±7%
Cash drawer function 2drives
Temperature Operating 0~50°C
Storage –10~50°C, without paper and ribbon cassette
Humidity Operating 10~90%, must be no condensation
Storage 10~90%, must be no condensation, without paper and
ribbon cassette
Overall dimensions (mm) Type A: 160 × 286 × 157.5 (W × D × H)
Type B: 160 × 248 × 138.5 (W × D × H)
Type D: 160 × 248 × 138.5 (W × D × H)
Mass (approx.) Type A: 2.7 kg Type B: 2.5 kg Type D: 2.3 kg

English
User’s Manual
DIP Switches and Specifications
The technical specifications and the information about the DIP switches are at the beginning of this
manual.
Illustrations
All of the illustrations are at the beginning of this manual. They are identified by letters (A, B, C . . .). In the
text the illustrations are referred to by these letters. (“See illustration A,” for example.) Some of these
illustrations have numbered arrows or lines pointing to parts of the illustration. See the list below for the
meaning of the numbers.
Because this manual covers three types of the TM-U220, some of the illustrations may be slightly different
from your printer; however, the instructions cover all types, except as noted.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with
respect to the use of the information contained herein. While every precaution has been taken in the
preparation of this book, Seiko Epson Corporation assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third
parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of:
accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this
product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any
options or any consumable products other than those designated as Original Epson Products or Epson
Approved Products by Seiko Epson Corporation.
Depending on the area, the interface cable may be included with the product. If so, use that cable.
Seiko Epson Corporation shall not be held liable for any damage resulting from electromagnetic
interference that occurs from the use of any interface cables other than those designated as Epson
approved products.
EPSON is a registered trademark of Seiko Epson Corporation. Exceed Your Vision is a registered
trademark or trademark of Seiko Epson Corporation. All other trademarks are the property of their
respective owners and used for identification purpose only.
NOTICE: The contents of this manual are subject to change without notice.
© Seiko Epson Corporation 2014. All rights reserved.
Illustration A
1. Roll paper cover
2. Ribbon cassette cover
3. Control panel
4. Power supply switch

2TM-U220 User’s Manual
English
Important Safety Information
This section presents important information intended to ensure safe
and effective use of this product. Read this section carefully and store
it in an accessible location.
Key to Symbols
The symbols in this manual are identified by their level of importance, as
defined below. Read the following carefully before handling the product.
WARNING:
Warnings must be followed carefully to avoid serious bodily injury.
CAUTION:
Cautions must be observed to avoid minor injury to yourself or damage to
your equipment.
Safety Precautions
WARNING:
Shut down your equipment immediately if it produces smoke, a strange
odor, or unusual noise. Continued use may lead to fire. Immediately unplug
the equipment and contact your dealer or a Seiko Epson service center for
advice.
Never attempt to repair this product yourself. Improper repair work can be
dangerous.
Never disassemble or modify this product. Tampering with this product may
result in injury or fire.
Be sure to use the specified power source. Connection to an improper
power source may cause fire.
Do not allow foreign matter to fall into the equipment. Penetration by
foreign objects may lead to fire.
If water or other liquid spills into this equipment, do not continue to use it.
Continued use may lead to fire. Unplug the power cord immediately and
contact your dealer or a Seiko Epson service center for advice.
If you open the DIP switch cover, be sure to close the cover and tighten the
screw after adjusting the DIP switch. Using this product with the cover open
may cause fire or electric shock.
Do not use aerosol sprayers containing flammable gas inside or around this
product. Doing so may cause fire.

TM-U220 User’s Manual 3
English
CAUTION:
Do not connect cables in ways other than those mentioned in this manual.
Different connections may cause equipment damage and burning.
Be sure to set this equipment on a firm, stable, horizontal surface. Product
may break or cause injury if it falls.
Do not use in locations subject to high humidity or dust levels. Excessive
humidity and dust may cause equipment damage or fire.
Do not place heavy objects on top of this product. Never stand or lean on
this product. Equipment may fall or collapse, causing breakage and
possible injury.
Take care not to injure your fingers on the manual cutter
• When you remove printed paper
• When you perform other operations such as loading/replacing roll
paper
To ensure safety, unplug this product before leaving it unused for an
extended period.
Before moving the product, unplug it and unplug all cables connected to it.
Safety Label
The caution labels on the product indicate the following precautions.
WARNING:
Do not connect a telephone line to the drawer kick out connector;
otherwise, the printer and the telephone line may be damaged.
CAUTION:
During printing or after printing, the print head can be very hot.
Notes on Usage
❏Do not open the cover during printing or when the autocutter is
being operated.
❏Do not install the printer in a dusty place.
❏Protect the printer from impact.
❏Cords or other foreign objects must not be caught on the printer.
❏Do not apply excessive force to the printer case.
❏Do not place food or beverages such as coffee on the case of the
printer.
Notes on Installation
❏When using the printer, be sure that the printer is installed
horizontally.

4TM-U220 User’s Manual
English
❏If you are using a Type B or D printer, you can hang it on a wall,
using the optional hanging bracket set, WH-10.
Note:
To hang the printer on a wall, see the WH-10 Installation Manual for
detailed instructions.
Notes on Connecting the Power Supply Unit
Be sure to use the correct power supply unit as listed below:
Note:
The “AC adapter, C,” which is packed with the alphanumeric model, cannot
be used with the multilingual* model. Be sure to use the “PS-180” with the
multilingual* model. If the “AC adapter, C,” packed with the alphanumeric
model, is connected to the multilingual* model by mistake, the printer might
not operate correctly. For example, printing might stop before all the lines are
printed or the printer might print the same line repeatedly.
*Multilingual means the printer model that can print any one of the following: Japanese Kanji,
Simplified Chinese, Traditional Chinese, Thai characters, or Korean characters.
Purpose of This Manual
This manual provides information to operators of the TM-U220 to
describe basic operations to enable safe and correct use of the printer.
Restriction of Use
When this product is used for applications requiring high reliability/
safety, such as transportation devices related to aviation, rail, marine,
automotive, etc.; disaster prevention devices; various safety devices,
etc.; or functional/precision devices, etc.; you should use this product
only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system
reliability. Because this product was not intended for use in
applications requiring extremely high reliability/safety, such as
aerospace equipment, main communication equipment, nuclear
power control equipment, or medical equipment related to direct
medical care, etc., please make your own judgment on this product’s
suitability after a full evaluation.
TM-U220 alphanumeric model (types A, B, and D) TM-U220 multilingual* model (types A, B, and D)
“AC adapter, C” (packed with the alphanumeric
model) or “PS-180” (option) “PS-180” (packed with the multilingual* model)

TM-U220 User’s Manual 5
English
Unpacking
The following items are included for the standard specification
printer. If any item is damaged, contact your dealer.
❏Printer
❏Roll paper
❏Exclusive ribbon cassette [ERC-38]
❏AC adapter (May not be included with the printer.)
Downloading Drivers, Utilities, and Manuals
Drivers, utilities, and manuals can be downloaded from one of the
following URLs.
For customers in North America, go to the following web site:
http://www.epsonexpert.com/ and follow the on-screen instructions.
For customers in other countries, go to the following web site:
http://download.epson-biz.com/?service=pos
Control Panel (LEDs and Buttons)
See illustration B.
LEDs
POWER (POWER)
Lights when the power is on and is off when the power is off.
ERROR (ERROR)
Lights when the printer is offline (when the roll paper is at the end, or
the roll paper cover is open). Off when the printer operates correctly.
Flashes when an error occurs. (See the Troubleshooting section.)
PAPER OUT (PAPER OUT)
Lights when roll paper is out or nearly out.
Buttons
FEED (FEED)
FEED (FEED) feeds the roll paper.
Note:
Paper cannot be fed by using this button when a paper out is detected.

6TM-U220 User’s Manual
English
Power Supply Switch and Power Supply Switch Cover
The power supply switch is on the front of the printer. Press the power
supply switch to turn on the printer.
Power Supply Switch Cover
You can use the enclosed power supply switch cover to make sure that
the power supply switch is not accidentally pressed. Just press the
cover into place to install it. If you need to turn the power supply
switch on or off with the cover attached, you can insert a thin tool into
one of the holes in the cover to operate the switch. See illustration C.
WARNING:
If an accident occurs when the power supply switch cover is attached,
immediately unplug the power supply cable to avoid fire.
If you are going to store the printer or leave it unused for a long time,
turn it off using the power supply switch on the printer.
Inserting and Replacing the Ribbon Cassette
CAUTION:
The print head becomes very hot during printing. Allow it to cool before
you replace the ribbon cassette.
CAUTION:
Never turn the ribbon cassette’s feed knob in the opposite direction of the
arrow marked on the cassette; otherwise the ribbon cassette may be
damaged.
Note:
Use the EPSON ERC-38 ribbon cassette for your printer.
1. Open the ribbon cassette cover by using the tabs on the sides of the
cover, as shown in illustration D.
2. Turn the knob two or three times in the direction of the arrow, as
shown in illustration E.
3. Insert the ribbon in the position shown in illustration Fand push
the ribbon cassette down until it clicks.
Note:
Make sure the ribbon is installed between the print head and the platen
without wrinkles or creases.

TM-U220 User’s Manual 7
English
4. Again turn the ribbon cassette’s knob 2 or 3 times in the direction
of the arrow and close the ribbon cassette cover.
CAUTION:
Be careful not to touch the print head with your fingers when turning
the ribbon cassette knob because the print head is hot and you might
be burned.
When you replace the ribbon casette, lift the left side of the ribbon
cassette first; then lift the whole ribbon cassette.
Inserting Roll Paper
CAUTION:
Be sure to use roll paper that meets the specifications.
Be sure not to touch the manual cutter. Otherwise your fingers might be
injured.
1. Using scissors, cut the leading edge of the roll paper, as shown in
illustration G.
2. Turn on the printer and open the roll paper cover by using the tab,
as shown in illustration H.
3. Type A only: Open the unit by using the unit open lever, as shown
in illustration I.
4. Insert the roll paper, as shown in illustration J.
Note:
Note the direction the paper comes off the roll, as shown in the illustration G.
When using 2-ply roll paper, be sure that the top and bottom sheets are
aligned at the paper exit. See illustration G-a.
5. If you are not using a take-up spool, pull out a small amount of
roll paper and close the roll paper cover; then tear off the paper
with the manual cutter. You can skip steps 6 through 11.
6. Type A only: When using 2-ply roll paper, pull out the roll paper to
the bottom front of the printer as a guide, as shown in illustration K.
7. Close the unit, as shown in illustration L.
8. Insert the end of the bottom paper (journal paper) into the paper
take-up spool, as shown in illustration M.
9. Insert the paper take-up spool in the printer. Be sure that the paper
is aligned with the spool’s flange, as shown in illustration N.
10. Feed the paper with the FEED (FEED) button so that the paper is
taken up by the spool.

8TM-U220 User’s Manual
English
11. Close the roll paper cover and tear off the roll paper with the
manual cutter, as shown in illustration O.
Note:
Do not open the roll paper cover during printing or paper feeding.
When using the printer, be sure to cut the roll paper with the manual cutter
after paper feeding is complete.
Replacing Roll Paper
1. Open the roll paper cover by using the tab, as shown in illustration H.
2. Types B and D: Remove the used roll paper core.
3. Type A only: Remove the take-up spool, and open the unit by
using the unit open lever, as shown in illustration I; then remove
the used roll paper core.
4. Insert new roll paper. See the section “Inserting Roll Paper”.
Troubleshooting
Printing stops before all the lines are printed or the printer prints the same
line repeatedly
If the correct power supply unit is not used, the printer cannot operate
correctly. Make sure the correct power supply unit is connected to the
printer, referring to the table below:
*Multilingual means the printer model that can print any one of the following: Japanese Kanji,
Simplified Chinese, Traditional Chinese, Thai characters, or Korean characters.
No lights on the control panel
Check the power supply cable connections and the power outlet.
The power supply unit that can be used with the
TM-U220 alphanumeric model (types A, B, and D)
The power supply unit that can be used with the
TM-U220 multilingual* model (types A, B, and D)
“AC adapter, C” (packed with the alphanumeric
model) or “PS-180” (option) “PS-180” (packed with the multilingual* model)

TM-U220 User’s Manual 9
English
ERROR (ERROR) LED is flashing or lit
❏The print head temperature may be too high or low. Wait until the
print head cools or warms and the printer resumes printing
automatically.
❏Make sure that the roll paper cover is properly closed.
❏Types A and B: The autocutter blade is not in the normal position
and the autocutter is locked up. If it is a simple lock-up, the error is
corrected automatically. If not, see the instructions below to return
the blade to the normal position manually.
❏A paper jam has occurred. To remove the jammed paper, see the
instructions below.
❏Turn off the power, wait several seconds, and then turn it on
again. If the error remains, contact your supervisor or a qualified
service person.
Returning the autocutter blade to the normal position
1. Open the roll paper cover by using the tab, as shown in
illustration H.
2. Use a ballpoint pen or tweezers to turn the knob of the autocutter
in the direction indicated by the arrow until you see a round shaft
in the hole, as shown in illustration P.
Removing jammed paper
CAUTION:
The print head becomes very hot during printing. Allow it to cool before
you reach into the printer.
1. Open the roll paper cover by using the tab, as shown in
illustration H.
2. If you have a Type A printer, remove the take-up spool and open
the unit by using the unit open lever, as shown in illustration I.
3. Remove the jammed paper.
4. Re-insert the roll paper and close the roll paper cover.

Français
Manuel d'utilisation
Commutateurs DIP et caractéristiques techniques
Les caractéristiques techniques et les informations concernant les commutateurs DIP se trouvent au début
du manuel.
Figures
Toutes les figures sont présentées au début du manuel. Elles sont identifiées par des lettres (A, B, C…).
Ces lettres sont utilisées dans le texte pour renvoyer aux figures. (Ex. : « Voir figure A».) Certaines
figures comportent des flèches ou lignes numérotées pointées vers des éléments particuliers. La liste
suivante indique la signification des numéros.
Étant donné que ce manuel couvre trois modèles de l'imprimante TM-U220, il se peut que certaines des
figures diffèrent légèrement de votre imprimante ; toutefois, sauf indication contraire, les instructions sont
valables pour tous les modèles.
Tous droits réservés. Sauf autorisation écrite préalable de Seiko Epson Corporation, la reproduction, la conservation
dans un système de stockage de données et la transmission sous quelque forme ou par quelque moyen que ce soit
(électronique, mécanique, par photocopie, enregistrement, etc…) d'une partie quelconque de la présente publication
sont interdits. La société décline toute responsabilité relative à l'exploitation des informations contenues dans le
présent document. Cet ouvrage a été rédigé avec le plus grand soin ; toutefois, Seiko Epson décline toute
responsabilité pour les erreurs et omissions qu'il pourrait contenir, ainsi que pour tous dommages résultant de
l'exploitation des informations qu'il contient.
La responsabilité de Seiko Epson Corporation ou de ses filiales ne saurait être engagée envers l'acheteur de ce
produit ou envers des tiers pour dommages, pertes, frais ou débours encourus par ceux-ci par suite d'accident ou
d'utilisation erronée ou abusive de ce produit, de modification, réparation ou transformation non autorisé de celui-
ci, ou (à l'exclusion des États-Unis), de toute utilisation du produit qui n'est pas strictement conforme aux
instructions d'utilisation et de maintenance de Seiko Epson Corporation.
Seiko Epson Corporation décline toute responsabilité pour dommages ou problèmes découlant de l'utilisation de
tous articles en option ou de toutes fournitures consommables autres que celles désignée produit d'origine Epson ou
produit approuvé Epson par Seiko Epson Corporation.
EPSON est une marque déposée de Seiko Epson Corporation. Exceed Your Vision est une marque déposée ou
commerciale de Seiko Epson Corporation. Toutes les autres marques appartiennent à leurs propriétaires
respectifs et sont utilisées uniquement à des fins d'identification.
REMARQUE : Le contenu de ce manuel est sujet à modification sans de préavis.
© Seiko Epson Corporation 2014. Tous droits réservés.
Figure A
1. Capot du rouleau de papier
2. Couvercle du compartiment
du ruban encreur
3. Panneau de commande
4. Interrupteur marche-arrêt

TM-U220 Manuel d'utilisation 11
Français
Importantes précautions de sécurité
D'importantes informations destinées à assurer un emploi sans danger
et efficace de ce produit sont présentées dans cette section. Lisez-la
attentivement et rangez-la dans un endroit facile d'accès.
Signification des symboles
Dans ce manuel, les symboles sont identifiés par ordre d'importance de
la manière indiquée ci-après. Lisez attentivement ce qui suit avant de
manipuler le produit.
AVERTISSEMENT :
Respectez strictement les avertissements afin d'éviter tout risque de
blessure grave.
ATTENTION :
Ces mises en garde doivent être respectées afin d'éviter les risques de
blessure légère ou de dégâts matériels.
Précautions de sécurité
AVERTISSEMENT :
Mettez immédiatement le matériel à l'arrêt si de la fumée ou une odeur
anormale s'en dégage ou s'il fait un bruit inusité. Il existe un risque
d'incendie si vous continuez à utiliser l'appareil. Coupez immédiatement
l'alimentation électrique et contactez votre revendeur ou un centre après-
vente Seiko Epson.
N'essayez jamais de réparer vous-même ce produit. Il peut exister des
dangers en cas de réparation incorrecte.
Ne procédez jamais au démontage ou à la modification de ce produit,
dont l'altération risque de poser des risques de blessure ou d'incendie.
Veillez à utiliser la source d'alimentation spécifiée. Le branchement à une
alimentation incorrecte pose des risques d'incendie.
Veillez à ne pas laisser quelque objet que ce soit tomber dans l'appareil,
car cela peut entraîner des risques d'incendie.
Si de l'eau ou un autre liquide pénètre dans l'appareil, cessez immédiatement
d'utiliser ce dernier. Il existe un risque d'incendie si vous continuez à utiliser
l'appareil. Débranchez immédiatement le cordon électrique et contactez
votre revendeur ou un centre après-vente Seiko Epson.
N’utilisez pas de bombes aérosol contenant des gaz inflammables à
l’intérieur ou à proximité de ce produit. Cela pourrait causer un incendie.
ATTENTION :
Ne branchez jamais les câbles d'une manière autre que celle indiquée
dans ce manuel. Un branchement incorrect risque d'endommager le
matériel et pose des risques d'incendie.

12 TM-U220 Manuel d'utilisation
Français
Veillez à installer cet appareil sur une surface horizontale ferme et stable. Il
existe des risques de dégâts matériels ou de blessure en cas de chute du
produit.
Évitez les endroits sujets à une humidité ou à une poussière élevée, car il
existe sinon des risques de dégâts matériels ou d'incendie.
Veillez à ne poser aucun objet lourd sur l'appareil. Ne montez et ne vous
appuyez jamais sur l'appareil. Il risquerait sinon de se briser ou de provoquer
des blessures en tombant ou en s'effondrant.
Prenez garde de ne pas vous couper les doigts au couteau manuel
• En retirant le papier imprimé
• Lors d’autres opérations somme le chargement/remplacement du
rouleau de papier
Par mesure de sécurité, débranchez l'appareil si vous ne comptez pas
l'utiliser pendant un certain temps.
Avant de déplacer l'appareil, débranchez son cordon électrique et
déconnectez tous les câbles qui lui sont reliés.
Étiquette de sécurité
Les étiquettes de mise en garde sur le produit indiquent les
précautions suivantes.
AVERTISSEMENT :
Ne raccordez pas de ligne téléphonique au connecteur du tiroir à ressort
car cela risquerait d'endommager l'imprimante et la ligne téléphonique.
ATTENTION :
Pendant ou après l'impression, la tête d'impression peut être brûlante.
Notes relatives à l'emploi
❏Ne pas ouvrir le capot pendant l'impression ou lorsque le coupe-
papier automatique est en service.
❏Ne pas installer l'imprimante dans un endroit poussiéreux.
❏Protéger l'imprimante contre les chocs.
❏Veiller à ce que des cordons ou autres objets étrangers ne
s'accrochent pas sur l'imprimante.
❏Ne pas appliquer de pression excessive au coffret de l'imprimante.
❏Ne pas placer d'aliments ou de boissons telles que du café sur le
coffret de l'imprimante.
Notes relatives à l'installation
❏Vérifiez que l'imprimante soit installée de manière bien
horizontale durant son utilisation.