Epson Dreamio EH-TW3800 User manual

About the Manuals and Notations Used
Types of Manual
The documentation for your EPSON projector is divided into the following two manuals. Refer to the
manuals in the order given below.
Safety Instructions/Support and Service Guide
This manual contains information on using the projector safely, and also includes a guide for warranty
service, and a troubleshooting check sheet.
Be sure to read this manual thoroughly before using the projector.
User’s Guide (this manual)
This User's Guide contains information on installing the projector, basic operations, using the
configuration menus, troubleshooting and maintenance.
Notations used in this User’s Guide
Safety indications
So that you can use the product safely and correctly, symbols are applied in the User's Guide and on the
product to indicate possible harm to the user or to others and the risk of damage to property.
The indications and their meaning are as follows. Make sure you understand them properly before reading
the guide.
General information
Meaning of "unit" and "projector"
When "unit" or "projector" appears in the text of this User’s Guide, they may refer to items which are
accessories or optional equipment in addition to the main projector unit itself.
This symbol indicates information that, if ignored, could possibly result in death or
personal injury due to incorrect handling.
This symbol indicates information that, if ignored, could possibly result in personal
injury or physical damage due to incorrect handling.
Indicates procedures where personal injury or damage to the projector may occur if
the procedures are not followed correctly.
Indicates additional information and points which may be useful to know regarding a
topic.
Indicates a page where useful information regarding a topic can be found.
Indicates that an explanation of the underlined word or words in front of this symbol
appears in the glossary of terms.
Refer to the "Glossary" in the "Appendix". p.57
, etc. Indicates buttons on the remote control or projector's control panel.
" (Menu Name) " Indicates configuration menu items.
Example: "Image"-"Color Mode"
[ (Name) ] Indicates the port name of the projector.
Example: [Video]
TIP

1
Checking the Components
When you unpack the projector, make sure that you have all these components.
If any of the components are missing or incorrect, please contact the place of purchase.
❏Projector (with lens cover) ❏Remote control
❏Power cable (3.0m)
Connect to the projector and to a wall outlet.
❏AA-size alkali batteries (2 pcs.)
Insert into the remote control.
❏Document CD-ROM
(Safety Instructions/Support and Service
Guide, User’s Guide)
❏Quick Start Guide
* Some regions may have paper manuals instead of a
CD-ROM, or may not have the Quick Start Guide.
Documentation

2
Table of Contents
■Features of the Projector.............................4
■Part Names and Functions..........................6
Front / Top.................................................... 6
Control panel ................................................ 6
Remote control ............................................. 7
Rear.............................................................. 8
Base ............................................................. 8
■Appearance................................................... 9
Installing the Projector
■Setting up.................................................... 10
Adjusting the projection size....................... 10
Projection methods..................................... 11
■Connecting Image Sources ....................... 12
■Preparing the Remote Control ..................13
Inserting batteries into the remote control .. 13
Using the remote control ............................13
Basic Operations
■Starting and Stopping Projection .............14
Turning the power on
and projecting images .............................. 14
When the expected images are
not projected............................................. 15
Turning the power off .................................15
Installing and removing the cable cover ..... 15
■Adjusting the Projection Screen...............16
Focus adjustment ....................................... 16
Projection size adjustment
(Zoom adjustment) ................................... 16
Projection image position adjustment
(Lens shift)................................................ 16
Adjusting the tilt of the projector ................. 17
Displaying a test pattern.............................17
Image Quality Adjustments
■Basic Image Quality Adjustments ............ 18
Selecting the color mode............................18
Selecting the aspect ................................... 18
■Advanced Color Adjustments................... 20
Hue, saturation, and brightness
adjustment ................................................ 20
Gamma adjustment .................................... 20
RGB adjustment (Offset, Gain) .................. 22
Selecting the color gamut...........................22
■Examining Image Quality Further ............. 23
Sharpness (Advanced) adjustment ............ 23
Auto Iris (automatic aperture) setting ......... 23
■Viewing Images at a Preset Image Quality
(Memory Function)...................................... 24
Saving, Loading, Erasing and Renaming
memory..................................................... 24
Configuration Menu
■Configuration Menu Functions .................26
Using the configuration menus................... 26
List of configuration menus (For the EH-
TW3800)................................................... 28
List of configuration menus (For the EH-
TW5000)................................................... 30
"Image" menu ............................................. 32
"Signal" menu ............................................. 33
"Settings" menu .......................................... 36
"Memory" menu .......................................... 38
"Reset" menu.............................................. 38

3
Table of Contents
Basic
operation
Appendix Troubleshooting Image Quality
Adjustments
Installing the
projector
Configuration
Menu
Troubleshooting
■Problem Solving ........................................ 39
Reading the indicators ............................... 39
•When the (warning) indicator is lit or
flashing...............................................................39
•Indicator statuses in normal operation..................40
When the indicators provide no help.......... 41
•Problems relating to images................................. 41
•Problems when projection starts.......................... 45
•Problems with the remote control........................ 46
Appendix
l
■Maintenance ............................................... 47
Cleaning..................................................... 47
•Cleaning the air filter............................................47
•Cleaning the projector case ..................................48
•Cleaning the lens ..................................................48
Consumable replacement periods ............. 49
•Air filter replacement period ................................49
•Lamp replacement period .....................................49
Replacing consumables............................. 50
•Replacing the air filter..........................................50
•Replacing the lamp...............................................50
•Resetting the lamp operating time........................50
■Optional Accessories/Consumables ....... 52
■List of Supported Monitor Displays ......... 53
•Component Video................................................ 53
•Composite Video/S-Video................................... 53
•Computer image (analog RGB) ........................... 54
•Input signal from the [HDMI1] / [HDMI2]
input port............................................................ 54
■Specifications ............................................ 55
■Glossary ..................................................... 57
■Index ........................................................... 59

4
Features of the Projector
Image appearance can be selected to match the
projection environment (Color Mode)
" " mode realizes more natural color
reproduction
Sophisticated color adjustment
The optimum images for the location can be projected simply by selecting the desired color mode from the
following seven preset modes.
If "Natural", "Cinema Night", "x.v.Color", "HD" or "Silver Screen" is selected, the Epson Cinema Filter effect
is applied automatically to increase the contrast and to make skin tones appear with more natural tints. p.18
In addition to the "Color Mode", the absolute color temperature and skin tones can be adjusted by simple
procedures to render the picture even more to your own liking. Further, you can adjust gamma, the offset and
gain for RGB colors, and the hue, saturation, and brightness of RGBCMY colors, to create colors that match the
image. p.20
Color
Mode
This mode is compatible with the extended-gamut color space standard for video (xvYCC).
Extended-gamut color images output by equipment supporting this standard are more faithful to the original,
and the viewer can enjoy clearer, more natural images. p.18
HD
Silver Screen
Vivid
Cinema Day
Natural
Cinema Night

5
Features of the Projector
Equipped with a wide-
angle lens shift function
The lens shift function allows the position of the
projected images to be adjusted vertically and
horizontally without distorting the images.
This can allow the projector to be set up with greater
freedom, even if it is suspended from a ceiling or at
an angle to the screen. p.16
For zoom adjustment, 2.1x short throw zoom lens is provided.
Images can be projected onto an 100" screen (16:9 screen
only) even at a distance of approximately 3 m (10 ft.). p.10
Advanced image quality adjustment functions such as "Auto Iris" and "Sharpness (Advanced)" can be used to
enjoy even sharper images. With the Auto Iris function turned on, the amount of light can be automatically
adjusted to match the images being projected, to create images with depth and perspective. The Sharpness function
is used to adjust not only the entire image, but also to emphasize specific regions, such as hair and clothing.
p.23
A variety of image setting functions
Advanced image quality adjustment functions
Some of the other many functions that are available are as follows.
EPSON Super White is used to prevent overexposure that can result in images that are too bright. p.35
A progressive conversion that lets you obtain ideal results both for images with large amounts of movement
and for still images. p.34
An aspect function that allows images to be viewed in wide-screen format. p.18
Memory functions that allow adjustment results to be stored and later retrieved easily using the remote control.
p.24
Lock settings that can be used to lock the projector's control panel after adjustments have been made so that
they cannot be changed by mistake, or to prevent children from accidentally turning on the power and looking
into the lens. p.36
Equipped with 2.1x short
throw zoom lens

6
Part Names and Functions
Front / Top
Control panel
Buttons with no explanation function in the same way as the corresponding buttons on the remote
control. Refer to "Remote control" for further details on these buttons.
•Front adjustable feet p.17
Extend to adjust the projection angle
so that the projector is horizontal
when placed on a desk top.
•Control panel (side)
See below
•Air exhaust vent
A discharge outlet for the air
which cools the inside of the
projector.
•Remote control light-
receiving area p.13
Receives signals from the
remote control.
•Vertical lens adjustment
dial p.16
Turn the dial to move the
position of the projection
image up or down.
•Lens cover
When not using the projector, attach this to the
lens to protect the lens from damage and dirt.
•
H
or
i
zon
t
a
l
l
ens a
dj
us
t
men
t
dial p.16
Turn the dial to move the position of the
projection image to the left or right.
Do not touch the exhaust vent
immediately after projecting, or
while projecting, since it
becomes hot.
•Focus ring p.16
Adjusts the image focus.
•Zoom ring p.16
Adjusts the image size.
•Control panel (top)
See below
•Remote control light-
receiving area p.13
Receives signals from the
remote control.
•Lamp cover p.50
Open this cover when replacing the
lamp inside.
•Projection lens
Projects images from here.
•Warning indicator p.39
Flashes or lights in different colors to
indicate problems with the projector.
•Power button
p.14, 15
•button
p.18, 20, 22, 26
•Enter/Line menu button
p.18, 24, 26
•Menu button p.26
•Source button p.15
Displays a list of input
sources and switches to
your desired input source.
•Esc button
p.18, 20
, 26
Top control panel Side control panel

7
Part Names and Functions
Remote control
•Remote control light-emitting area p.13
Outputs remote control signals.
•Power button p.14 , 15
Turns the projector power on/off.
•Memory button p.24
Saves, loads, and erases memory
contents.
•Default button p.26
Returns settings of the adjustment
screen in the configuration menu to
their default values when pressed
while displaying the screen.
•Enter/Line menu button
p.18, 24
, 26
Displays the line menu.
While viewing a menu, press this
button to select the menu item and
proceed to the next display.
•
button
p.18, 20, 22, 26
Press to select menu items and
adjustment values.
•Gamma button p.20
Adjusts the gamma.
•Sharpness button p.23
Adjusts the image sharpness.
•Blank button p.26
Turns off and on the projected
images temporarily.
When pressed while displaying
the configuration menu, the menu
screen disappears and appears.
•Illumination button
Illuminates all of the buttons on the
remote control for 10 seconds so
that they can be seen in dark
places.
•Color Mode button p.18
Changes the color mode to suit the
projection environment.
•Aspect button p.18
Changes the aspect ratio to match
the input signal.
•Esc button
p.18
, 20 , 26
Returns to the previous menu when
pressed while displaying the menu.
Switches the input source to the
input terminals indicated on each
button.
•Pattern button p.17
Displays and clears the test pattern.
•RGBCMY button p.20
Adjusts the hue, saturation and
brightness for each RGBCMY
color.
•Menu button p.26
Displays and closes the full
configuration menus.
Source buttons p.15

8
Part Names and Functions
Rear
Base
•[Trigger out] port
When the projector is
turned on, a 12 V DC
signal is output from this
port. When the projector is
turned off or a problem
with operation occurs, the
output becomes 0 V to
send the projector's power
ON/OFF status to an
external device.
•[Video] input port p.12
Inputs a general video signal
(composite video). Connect to an
image output port of a video
source.
•[HDMI1] input port
p.12
Connects to an HDMI -
compatible video source
or to a computer.
•[S-Video] input port p.12
Connects to the S-Video out ports
of the video equipment.
•[RS-232C] port
Connects to a computer using an RS-232C
cable to control the projector from the
computer. This is not used in normal use.
•[Power] inlet p.14
Connects the power cable.
•Main power switch
p.14
•Security lock
p.58
•[PC] input port p.12
Connects to the RGB out
port of the computer.
•[Component] input port
p.12
Connects to the component
(YCbCr or YPbPr ) out
port of the video equipment.
•[HDMI2] input
port p.12
Connects to an HDMI-
compatible video source
or to a computer.
•Lamp cover open switch p.50
Press to open the lamp cover.
•Air inlet (air filter) p.47, 50
This draws in air for cooling the
inside of the projector. If dust collects
on the filter, the temperature inside
the projector will rise and problems
with operation or more rapid
deterioration of the optical
components may occur. The air filter
should be cleaned periodically.
•Cable holders
When an HDMI cable with a large outer
diameter is connected to the input port, the
weight of the cable may cause it to hang
down and result in a poor connection. To
prevent this by securing the cable, you can
pass a commercially-available cable tie
through one of the two holders whichever is
more convenient for you.
Cable tie
(commercially available)
•Suspension bracket fixing
points (5 points) p.52
Install the optional ceiling mount
here when suspending the projector
from a ceiling. •Cable cover stays
(2 places)
Attach the optional cable cover
here.

9
Appearance
Centre of lens
* Distance from centre of lens to suspension bracket fixing point
Units:mm
Centre of lens
450
131
148.3
4.5
12.3
134.7
5-M4×9
389.7
150
136
160
45
75
300
56
72*

10
Setting up
Adjusting the projection size
-17 to 55 (-6.8 to 21.5)
-23 to 73 (-9.1 to 28.7)
-35 to 109 (-13.6 to 43.0)
-58 to 182 (-22.7 to 71.7)
-69 to 219 (-27.0 to 86)
-46 to 146 (-18.2 to 57.4)
-86 to 273 (-34.0 to 107.6)
Centre of lens
Screen
Adjusting the projection size
Lens shift adjustment
When the projector is further away from the screen, the projection image size are larger.
While referring to the table below, position the projector so that the images are projected onto the
screen at the optimum size.
The values should be used as a guide for setting up the projector.
Suspending from the ceiling
A screen in a high location
Projector situated to the side so that the screen can be viewed sitting right in front of it
Projector situated on a shelf, etc.
When positioning an image using the lens shift dial, hardly any deterioration of the image occurs because the lens
shift correction is adjusted optically. However, for optimal image quality the lens shift function should not be used.
The lens shift dials can be used to position the image and is especially useful when using the projector in the
following locations. p.16
This is the height from the centre of the lens to the bottom of the
projection images. It can be changed by the vertical lens shift
setting.
If the projector is placed at an angle to
the screen, then the projected image will
be distorted.
4:3 screen size
Units: cm (in.)
Units: cm (in.)
16:9 screen size Longest
(Tele)
Shortest
(Wide) to
Projection distance
Projection distance
120×90 (47×35)
160×120 (63×47)
200×150 (79×59)
61×46 (24×18)
81×61 (32×24)
240×180 (94×71)
60"
100"
80"
30"
40"
120"
150" 300×230 (118×91)
130×75 (51×28)
180×100 (71×39)
220×120 (87×47)
177 to 380 (70 to 150)
298 to 636 (117 to 250)
66×37 (26×15)
89×50 (35×20)
87 to 188 (34 to 74)
117 to 252 (46 to 99)
238 to 508 (94 to 200)
270×150 (106×59)
60"
100"
80"
30"
40"
120"
150" 330×190 (130×75)
359 to 764 (141 to 301)
450 to 956 (177 to 376)
Vertical lens shift
Highest to Lowest
-21 to 67 (-8.3 to 26.3)
-28 to 89 (-11.1 to 35.1 )
-42 to 134 (-16.7 to 52.7)
-71 to 223 (-27.8 to 87.8)
-85 to 268 (-33.0 to -105.0)
-56 to 178 (-22.2 to 70.2)
-106 to 334 (-41.7 to 131.7)
218 to 466 (86 to 183)
366 to 779 (144 to 307)
107 to 231 (42 to 91)
144 to 309 (57 to 122)
292 to 623 (115 to 245)
440 to 936 (173 to 368)
551 to 1171 (217 to 461)
Longest
(Tele)
Shortest
(Wide) to
Screen
Projection distance
-115 to 364 (-45.4 to 143.5)
200" 440×250 (179×98) 601 to 1276 (236 to 502)
Vertical lens shift
Highest to Lowest
200" 410×300 (161×118) -141 to 446 (-55.6 to 175.6)
736 to 1562 (290 to 615)

11
Setting up
Installing the Projector
Projection methods
* When suspending the projector from a ceiling,
change the configuration menu settings. p.37
When projecting from a celling * Even if projection will be from the screen
side, set up the screen and projector so that
they are parallel.
Configuration menu
Settings Projection
Front
Front/Ceiling
Projection methods
TIP
You can rotate the EPSON logo plate around 180 degrees when suspending
the projector from a ceiling.
When one end of the plate is pressed, the
opposite end lifts up, so you can pull it out
slightly, turn it around and then push it back in.
A special method of installation is required when suspending the projector from
the ceiling (ceiling mount). If it is not installed correctly, it could fall causing an
accident and injury.
If you use adhesives on the ceiling mount to prevent the screws from loosening,
or if you use things such as lubricants or oils on the projector, the projector case
may crack causing it to fall from its ceiling mount. This could cause serious injury
to anyone under the ceiling mount and could damage the projector.
When installing or adjusting the ceiling mount, do not use adhesives to prevent
the screws from loosening and do not use oils or lubricants and so on.
When projecting from directly in front When projecting from the side of
the screen
Avoid setting the projector up in a place which is very dusty or humid, or where there
will be cigarette or other smoke, especially oily smoke.
Clean the air filter at least once every 3 months.
Clean the air filter more frequently if using the projector in a dusty environment.
Do not use the projector on its side. This may cause malfunctions to occur.

12
Connecting Image Sources
•Turn the power off for both the projector and the signal source before connecting them.
If the power for either device is on at the time of connection, damage may result.
•Check the shapes of the cable connectors and the device ports before making the
connections. If you try to force a connector to fit a device port with a different shape or
number of terminals, a malfunction or damage to the connector or port may result.
•Some signal sources may have specially-shaped ports. In such cases, use the
accessory or optional cables that are supplied with the signal source to make the
connections.
•The cable that should be used to connect video equipment to the projector will depend
on the type of video signal that the equipment outputs. Some kinds of video equipment
output several different types of video signal. The image quality ranking of the video
signal types is generally held to be as follows, in descending order of quality:
Digital component video [HDMI ] > Analog component video [Component] >
S-Video [S-Video] > Composite video [Video]
You should refer to the documentation provided with the video equipment being used to
check what types of video signal formats the equipment can output. The composite
video format is sometimes simply called "video output".
*Use a HDMI cable that conforms to the HDMI specifications.
Video equipment (VHS VCR, DVD player, game console, etc.)
*Port names may vary depending on the equipment being connected.
Computer
S-Video
S-Video cable
(commercially-
available)
Video
Component
video cable
(commercially-
available)
HDMI cable
(commercially-
available *)
Component output
Mini D-Sub
15-pin
Mini D-Sub
15-pin
Computer cable
(commercially-
available)
HDMI
RCA video cable
(commercially-
available)
TIP

13
Installing the Projector
Preparing the Remote Control
Inserting batteries into the remote control
Using the remote control
If delays in the responsiveness of the remote control occur or if it does not operate
after it has been used for some time, it probably means that the batteries are
becoming flat. If this happen, replace the batteries with two new batteries. Use two
new AA-size alkali batteries or manganese batteries as replacement batteries.
Batteries other than AA-size alkali batteries or manganese batteries cannot be used.
At the time of purchase, the batteries are not
inserted into the remote control. Insert the supplied
batteries before using the remote control.
Insert the batteries in the correct direction.
Close the cover.
Check the (+) and (-) indications inside
the battery compartment and insert the
batteries so that they face correctly.
Lift up the battery cover while pressing its
tab.
TIP
Approx.30
Approx.30
Approx.30
Approx.10m
Operating distance
Approx.30
Approx.30
Operating range (horizontal)
Operating range (vertical)
Approx.10m
Operating distance
Approx.60
Approx.10 *
Approx.30
Approx.10m
Operating distance
Approx.10m
Operating distance
* Remote control signals
cannot be received within this
range.

14
Starting and Stopping Projection
Turning the power on and projecting images
TIP
If you set the "Direct Power On" to "On", the power of the unit will turn ON when
the main power switch is turned ON, without having to press the power button of
the remote control or the projector's control panel. p.36
If there is a problem with projection even though the projector is set up and connected correctly,
refer to p.15, 39.
The projector is equipped with a "Child Lock" function that prevents young
children from accidentally turning the power on and looking into the lens, and
also an "Control Panel Lock" function that prevents mis-operations. p.36
When using above an altitude of about 1500 m, make sure you set the "High
Altitude Mode" to "On". p.36
This projector is equipped with an automatic
adjustment function that automatically optimizes it
when a computer input signal is switched.
If a laptop computer or a computer with a LCD
screen has been connected to the projector, you
may need to use keyboard or function settings to
change the output destination. While holding down
the key, press (the key with a symbol such
as / on it). After the selection is made,
projection will soon start.
Computer's documentation
NEC
Panasonic
SOTEC
HP
Toshiba
IBM
LENOVO
SONY
DELL
Fujitsu
Macintosh
Example of output selection
Set mirror setting or
display detection.
Depending on OS, you can
change the output
selection by pressing .
ON
Remove the lens cover.
Connect the
power cable.
Turn on the main power switch.
Turn the power on for the
connected equipment.
Turn the power on.
Control Panel Remote Control
Do not look into the lens
while projection is in
progress.
(Commercially-
available)

15
Starting and Stopping Projection
Basic Operations
When the expected images are not
projected
Turning the power off
Installing and removing the cable
cover
When the expected images are not
projected
Turning the power off
Simply pressing or does not stop
electricity consumption.
If more than one signal source has been connected, or if no images are projected, use the remote control or the
projector's control panel buttons to select the signal source. For video devices, press the [Play] button on the video
equipment first, then select the signal source.
Using the remote control
Press the button that has the name of the port
on it that the desired signal source is connected
to.
Using the control panel
When you press , the menu is displayed.
Each press of moves the pointer. Move the pointer to the
target input source to select it.
The input source is automatically switched when no operations are
performed about three seconds with placing pointer at the target
input source. You can also press to switch to the target source.
Turn the power off for the signal sources
that are connected to the projector.
Press on the remote control or on
the projector's control panel.
Attach the lens cover.
When cool-down (approximately 16 seconds)
is completed, flashing around the stops
and you can then turn off the main power
switch.
TIP
When the color of the image projected from the [Component] input port is
unnatural, select an appropriate signal according to the signal from the device
connected at "Input Signal" in the Configuration menu. p.37
When the expected images are not projected
Turning the power off
If the projector is suspended from a ceiling and the
lens cover is left removed, the lens cover will still be
needed if the projector is moved anywhere, so keep
it in a safe place.
The following message is displayed, so press or
once more.
When the projector is suspended from a ceiling, you can use the cable cover to improve the appearance.
Installing and removing the cable cover
Installing the cable cover Removing the cable cover

16
Adjusting the Projection Screen
Focus adjustment
Projection size adjustment (Zoom
adjustment)
Projection image position adjustment
(Lens shift)
If the projector cannot be set up directly in
front of the screen, you can use the lens
shift function to move the position of the
projected images vertically or horizontally
within the range shown at right. While
turning the lens shift dials, the position
where a click is heard is currently at about
the middle of the shift range.
The image position cannot be moved to the
maximum vertical values and maximum
horizontal values at the same time.
Standard projection position
(centre position for lens shift)
Range that the picture can be shifted
from the standard projection position
V
1/2H
1/2H
H
1/2V
1/2V
Turn the focus ring to adjust the focus.
Turn the zoom ring to adjust the size of the projected image.
Ex) The image cannot be shifted
vertically when it has been shifted
horizontally by the full amount.
When the image has been shifted
vertically by the full amount, it can
be shifted up to 9% of the horizontal
width of the screen.
Move
upwards
Move to
the left
Move to
the right
Wide
Te l e
Focus adjustment
Focus adjustment
Focus adjustment
Focus adjustmentFocus adjustmentFocus adjustmentFocus adjustment
Focus adjustment
Focus adjustment
Focus adjustment
Projection size adjustment (Zoom adjustment)
Projection image position adjustment (Lens shift)
Move
downwards
When transporting the
projector, make sure to turn the
lens position down by the full
amount. Otherwise the lens
shift mechanism may be
damaged.

17
Adjusting the Projection Screen
Basic Operations
Adjusting the tilt of the projector
Displaying a test pattern
Extend Extend Retract Retract
When an image from the projector that is placed on a flat surface is tilting horizontally ( ), use the
front feet to correct the tilt.
You can adjust zoom, focus, and color without having to connect video equipment.
Press on the remote control to display the menu. To carry out zoom or focus adjustment or
adjustment of the projection position using the lens shift function, select "Display Position" and then press
. When carrying out color adjustment, select the color to be adjusted from "Color Isolation: R/G/B" and
then press . For example, if you select "Color Isolation: R" only the red component of the image will be
projected, as if you view images through a red filter which is provided with a commercially-available
monitor checking disk. In this condition, you can adjust the color saturation and tint in the same way as the
adjustment method described on the monitor checking disk. Since you do not have to hold a color filter,
you can make color adjustments much easier.
1/2H
1/2V
To stop displaying the test pattern, press to display the menu then select "Exit".
Adjusting the tilt of the projector
Displaying a test pattern
When "Display Position" is selected

18
Basic Image Quality Adjustments
Selecting the color mode
Selecting the aspect
Selecting the color mode
Press and select the
color mode from the menu.
Setting is also possible using
the configuration menu.
Inputting a signal to the
HDMI1/HDMI2 terminals.
*If you press , the Select
menu disappears.
Select Menu Operations
Use to select an item.
Press to confirm the selection.
If you project an image that is
compressed, enlarged or separated
using the aspect function in public
places such as a store or hotel for the
purposes of profit-making or public
display, it may result in infringing on the
author's right that is protected by
copyright law.
TIP
Press and select the aspect mode from the menu.
When projecting using
Auto
Not usable during computer input. Not compatible
with certain component video signals.
If Auto is not suitable, the setting will become
Normal.
● For 4:3 input signals
● For input images
recorded
in squeeze mode
● For letterbox input signals
Normal
Normal
When HDTV images
are projected, the
images appear in 16:9
size.
Black bands will
appear at the left and
right of the images.
Input signal
Recommended
aspect mode
Result
Remarks
Normal TV broadcasts
Images with standard
aspect ratio (4:3)
Computer images
Selecting the aspect
Zoom
Full