Epson EB-G6750WU User manual

Installation Guide

Notations Used in This Guide
•Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
Please understand and respect these caution symbols in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
•General information indications
Attention
Indicates procedures which may result in damage or injury if sufficient care is not taken.
a
Indicates additional information and points which may be useful to know regarding a topic.
sIndicates a page where detailed information regarding a topic can be found.
[Name] Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Menu Name Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness

Notations Used in This Guide ........................ 2
Main Guide
Part Names and Functions ................................... 6
Front/Top...................................................6
Rear....................................................... 7
Interface....................................................7
Base.......................................................8
ControlPanel.................................................9
RemoteControl...............................................10
Remotecontroloperatingrange................................. 10
RemovingandAttachingtheProjectorLensUnit ............. 12
Removing...................................................12
Attaching ...................................................13
TurningOnandOff ........................................ 15
TurningOn ..................................................15
TurningOff ..................................................15
ReadingtheIndicators ..................................... 16
Installing the Projector ..................................... 20
InstallationRequirements ........................................ 20
Changingthedirectionoftheimage(projectionmode).................21
AdjustingthePositionoftheProjectedImage(LensShift) .................. 22
AdjustingtheZoom............................................23
AdjustingtheFocus............................................ 23
WhenusingtheshortthrowzoomlensELPLU01 ......................23
AdjustingtheImagePosition(WhenSetuponaDesk)....................24
AdjustingtheHorizontalTilt(WhenSetuponaDesk).....................25
ScreenSettings............................................... 25
Adjustingthepositionoftheimageontheprojectedscreen..............25
DisplayingaTestPattern ........................................26
SettingUp ................................................ 28
IDSettings..................................................28
SettheprojectorID ..........................................28
CheckingtheProjectorID ...................................... 28
SettingtheremotecontrolID ................................... 28
SettingtheTime ..............................................29
OtherSettings ................................................31
Settingbasicoperations .......................................31
Settingthedisplay ...........................................32
SavingaUser'sLogo ...........................................33
Connecting Equipment ..................................... 34
ConnectingaComputer.........................................34
ConnectingImageSources .......................................36
ConnectingExternalEquipment...................................38
ConnectingaLANCable ......................................... 39
Connecting an HDBaseT Transmitter (EB-G6750WU Only) ..................40
InstallingtheWirelessLANUnit.................................... 41
AttachingtheCableCover ....................................... 42
Attaching.................................................42
ProjectingImages ......................................... 43
CorrectingDistortionintheProjectedImage ...........................43
Controlpanel..............................................43
Remotecontrol.............................................43
H/V-Keystone..............................................43
QuickCorner ...............................................44
ArcCorrection..............................................45
PointCorrection............................................46
ChangingtheAspectRatiooftheProjectedImage ......................47
Changingmethods.......................................... 48
Multi-Projection..............................................50
PreparingtheProjector .......................................50
Workflow .................................................51
Scale .................................................... 54
Projecting3Dimages........................................... 55
ImageMaintenance ............................................56
PanelAlignment............................................56
Contents
3

ColorUniformity............................................57
SecurityFunctions ......................................... 59
ManagingUsers(PasswordProtection) ...............................59
KindsofPasswordProtection...................................59
SettingPasswordProtection ....................................59
EnteringthePassword ........................................60
RestrictingOperation...........................................61
ControlPanelLock ...........................................61
Remotecontrolbuttonlock ....................................62
Anti-TheftLock ............................................... 62
Installingthewirelock ........................................63
NetworkSetup ............................................ 64
CheckingNetworkSettings.......................................64
WirelessLAN .................................................64
PreparingtheProjector .......................................64
Adhocconnectionsettings(Quick) ...............................64
Infrastructureconnectionsettings(Advanced)........................65
WiredLAN..................................................67
ListofMenusforOtherNetworkSettings ............................. 68
Securitymenu ............................................. 68
AdministratorSettingsmenu...................................70
MailNotificationmenu........................................72
ManageCertificatesmenu.....................................73
SNMPmenu...............................................75
Resetmenu............................................... 76
AboutEventID ...............................................77
Notes on Transportation ................................... 79
MovingNearby...............................................79
WhenTransporting ............................................79
Preparingpackaging.........................................79
Noteswhenpackingandtransporting .............................79
GeneralNotes ............................................. 80
TrademarksandCopyrights......................................80
Epson Projector Contact List . . .............................. 81
Europe .....................................................81
Africa ......................................................86
MiddleEast ..................................................87
North,CentralAmericaandCaribbeanIslands ..........................87
SouthAmerica...............................................88
AsiaandOceania ..............................................89
Contents
4

Main Guide

Front/Top
Name Function
AAir exhaust vent Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands
near the air exhaust vent, and do not place objects
that may become warped or damaged by heat near
the vent. Hot air from the air exhaust vent could
cause burns, warping, or accidents to occur.
BFocus ring Adjusts the image focus. sp.23
CZoom ring Adjusts the image size. sp.23
Name Function
DLens unit removal
button
When replacing the lens unit, press this button and then
remove the lens unit.
ERemote receiver Receives signals from the remote control.
FStatus indicators The color of the indicators and whether they are flashing
or lit indicate the status of the projector. sp.16
GWireless LAN indicator Indicates the access status of the optional wireless LAN
unit.
HAir intake vent
(air filter)
Takes in air to cool the projector internally.
ISpeaker Outputs audio.
JAir filter cover
operation knob
Use this knob to open the air filter cover.
KCable cover Cover for the rear interface cable connection section.
sp.42
LVertical lens shift dial Turn the dial to move the position of the projected image
up or down. sp.22
MLens shift dial lock Locks or releases the lens shift dials.
NHorizontal lens shift
dial
Turn the dial to move the position of the projected image
left or right. sp.22
OLamp cover Open when replacing the projector's lamp.
Part Names and Functions
6

Rear
Name Function
AInterface s"Interface" p.7
BSecurity slot The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
sp.62
CPower inlet Connects to the power cable.
DControl panel s"Control Panel" p.9
ECable holder Insert the supplied cable clamp here to prevent the HDMI
cable from falling out.
Interface
Name Function
AAudio1 port Inputs audio from equipment connected to the Computer
port.
BComputer port For analog RGB signals from a computer and component
video signals from other video sources.
CBNC port For analog RGB signals from a computer and component
video signals from other video sources.
DAudio2 port Inputs audio from equipment connected to the BNC port.
ERS-232C port When controlling the projector from a computer, connect
it to the computer with an RS-232C cable. This port is for
control use and should not normally be used.
FRemote port Connects the optional remote control cable set and inputs
signals from the remote control. When the remote control
cable is plugged into the Remote port, the remote receiver
on the projector is disabled.
GAudio-L/R port Inputs audio from equipment connected to the Video port
or the S-Video port.
HVideo port Inputs composite video signals from video sources.
IS-Video port For S-video signals from video sources.
Part Names and Functions
7

Name Function
JAudio Out port Outputs audio from the currently projected image to an
external speaker.
KMonitor Out port Outputs to an external monitor the analog signal from the
computer connected to the Computer port or the BNC
port. You cannot output signals input from other ports or
component video signals.
LDisplayPort Inputs video signals from DisplayPort compatible
computers. This projector is compatible with HDCP.
MHDMI port Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with HDCP.
NAudio3 port Inputs audio from equipment connected to the
DisplayPort or the HDMI port.
OHDBaseT port (EB-
G6750WU only)
Connects a LAN cable to the optional HDBaseT
Transmitter. sp.40
PLAN port Connects a LAN cable to connect to a network.
QService port Control port used when updating the projector's software.
This should not normally be used.
Base
Name Function
AFront adjustable foot When setup on a surface such as a desk, extend the foot to
adjust the position of the image. sp.24
BRear feet When setup on a surface such as a desk, turn to extend and
retract to adjust the horizontal tilt. sp.25
CScrew holes to fix the
cable cover
Screw holes to fix the cable cover in place. sp.42
DSecurity cable
installation point
Pass a commercially available wire lock through here and
lock it in place. sp.63
Part Names and Functions
8

Name Function
ECeiling mount fixing
points (four points)
Attach the optional Ceiling Mount here when suspending
the projector from a ceiling. sp.20
FScrew hole for the
screw to fix the lens
unit removal button
When installing a lens unit, use this screw hole to fix the
lens unit removal button using the screw supplied.
sp.12
Control Panel
Name Function
A[t] button Turns the projector power on or off.
B[Source Search]
button
Changes to the next input source that is sending an image.
C[]/[ ] buttons •Displays the Control Panel Lock screen allowing you to
make settings to lock the control panel buttons.
sp.61
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
Name Function
D[] button •When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
•If pressed while projecting analog RGB signals from the
Computer port or the BNC port, you can automatically
optimize Tracking, Sync., and Position.
E[]/[ ] buttons •Displays a test pattern. sp.26
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
F[] /[ ] buttons •Displays the Info menu from the Configuration menu.
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
G[A/V Mute] button Turns the video and audio on or off.
H[Esc] button •Stops the current function.
•If pressed when the Configuration menu is displayed, it
moves to the previous menu level.
I[]/[ ] buttons •Performs screen adjustments using the settings in
Geometric Correction from the Configuration menu.
sp.43
•If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
J[Menu] button Displays and closes the Configuration menu.
Part Names and Functions
9

Remote Control
See the User's Guide for information on basic remote control operations.
Remote control operating range
a
•To restrict reception of the operation signals from the remote
control, set Remote Receiver.
Press [Menu] button > Settings > Remote Receiver
•When using a remote control provided with other Epson projectors,
set the Remote Control Type.
Press [Menu] button > Extended > Operation > Remote Control
Type
The operating range and operation section depends on the remote
control that you use.
Part Names and Functions
10

You can perform the following operations by simply pressing one button on
the remote control.
Operation Settings
Reverses the top and bottom of a projected
image. (Changes Front and Front/Ceiling
in Projection) sp.21
Hold down the [A/V Mute] button for at
least five seconds.
Sets password protection sp.59 Hold down the [Freeze] button for at least
five seconds. Make the settings on the
Password Protection screen.
Applies or releases a partial lock for the
remote control buttons. sp.62
Hold down the [Help] button for at least
five seconds.
Resets the Remote Receiver settings on
the Configuration menu. (Enables all of
the projector's remote receivers.)
Hold down the [Menu] button for at least
15 seconds.
Displays frequently used Configuration
menu items instantly.
Press the [User1], [User2], or [User3]
button. You can set the menu item
assigned to each button from User
Button.
Press [Menu] button > Settings > User
Button
The following items can be assigned.
Power Consumption, Info, Progressive,
Geometric Correction, Multi-
Projection, Resolution, Memory, or
Image Processing
Part Names and Functions
11

Removing
Attention
•Only remove the lens unit when necessary. If dust or dirt enter the projector,
projection quality deteriorates and it could cause a malfunction.
•Try not to touch the lens section with your hand or fingers. If fingerprints or
oils are left on the surface of the lens, projection quality deteriorates.
•If the lens shift has been done, set the lens shift to the center before replacing
the lens unit.
s"Adjusting the Position of the Projected Image (Lens Shift)" p.22
a
When the lens unit removal button is fixed with a screw, remove
the screw.
b
While pressing the lens unit removal button, turn the lens unit
counterclockwise until you hear it click.
c
Pull the lens unit straight out as it is released.
Removing and Attaching the Projector Lens Unit
12

Attaching
See the following for a list of lenses that can be used with the projector.
Only use the specified lens.
Lens
Type
Lens
Model
Number
Projector Model Number
EB-
G6900WU
G6800
G6750WU
G6650WU
G6550WU
G6450WU
G6350
G6250W
G6150
G6050W
EB-G5950
G5900
G5800
G5750WU
G5650W
G5600
G5500
G5450WU
EB-G5350
G5300
G5200W
G5150
G5100
EB-4955WU
4950WU
4855WU
4850WU
4750W
4650
4550
Standard
Lens
ELPLS06 Yes Yes Yes Not supported
ELPLS05 No Yes Yes
ELPLS03 No Yes
*
Yes
Short
throw
zoom
lens
ELPLU01 Yes No No
Rear
projection
wide
lens
ELPLR03 Yes Yes Yes
Middle
throw
zoom
lens
ELPLM04 Yes Yes Yes
ELPLM05 Yes Yes Yes
Lens
Type
Lens
Model
Number
Projector Model Number
EB-
G6900WU
G6800
G6750WU
G6650WU
G6550WU
G6450WU
G6350
G6250W
G6150
G6050W
EB-G5950
G5900
G5800
G5750WU
G5650W
G5600
G5500
G5450WU
EB-G5350
G5300
G5200W
G5150
G5100
EB-4955WU
4950WU
4855WU
4850WU
4750W
4650
4550
Long
throw
zoom
lens
ELPLL06 Yes Yes Yes
*This is not available for EB-G5750WU/EB-G5450WU.
Attention
Do not attach the lens unit when the projector's lens insertion section is
facing up. Dust or dirt could enter the projector.
a
Turn the focus ring clockwise until it cannot go any further.
Removing and Attaching the Projector Lens Unit
13

b
Insert the lens unit straight into the projector's lens socket with
the white dot at the top, and then turn it clockwise until you hear
it click into place.
Turn the torque ring on the lens unit to adjust the torque for the
zoom ring.
ATighter
BLooser
c
Turn the lens unit counterclockwise and make sure that it does
not come out of the socket.
d
Fix the lens unit removal button with the screw supplied with the
lens unit.
Make sure you fix the lens unit removal button with the screw to
prevent the lens unit from being stolen.
Attention
•Store the projector with the lens unit installed.
If the projector is stored without the lens unit, dust and dirt may get inside
the projector and cause malfunctions or lower the quality of projection.
•When the projector is facing up (35 to 150 degrees) or down (-35 to -150
degrees), tighten the lens torque ring. Note that it could malfunction if it is
over tightened.
Removing and Attaching the Projector Lens Unit
14

Turning On
a
Connect the power cable.
Connect the power cable supplied.
b
Turning on the projector.
Using the remote control Using the control panel
Warning
Do not look into the lens during projection.
a
•We recommend setting the focus, zoom, and lens shift at least
30 minutes after you start the projection, because images are
not stable right after turning on the projector.
•When using at an altitude of 1500 m or more, make sure you
set High Altitude Mode to On.
Press [Menu] button > Extended > Operation > High
Altitude Mode
•When you turn on the projector for the first time, the
message "Do you want to set the time?" is displayed. See the
following for more information on setting the time.
sp.29
Turning Off
a
Turn off any connected devices.
b
Press [t] once on the remote control, or press [t] twice on the
control panel.
Using the remote control Using the control panel
× 2
c
When the projector beeps twice, disconnect the power cable.
a
To prevent accidental operations, set Standby Confirmation to On to
display a confirmation message asking if you want to turn off the
projector when the [t] button is pressed on the remote control.
(When Remote Control Type is set to Simple, you cannot make
Standby Confirmation settings.)
Press [Menu] button > Extended > Display > Standby Confirmation
After making the settings, a confirmation message is displayed when
you press the [t] button on the remote control, and the projector
turns off if you press the [t] button one more time.
Turning On and Off
15

The projector is provided with the following four indicators that indicate the operating status of the projector.
APower indicator Indicates the operating status.
Standby condition
In this status, you can start projecting by pressing the [ ] button on the remote control, or the [t] button
on the control panel.
Preparing for network monitoring or cool down in progress
All buttons are disabled while the indicator is flashing.
Warming up
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
The [t] button is disabled during warm-up.
Projecting
BLamp indicator Indicates the projection lamp status.
CTemp indicator Indicates the internal temperature status.
DFilter indicator Indicates the air filter status.
Reading the Indicators
16

Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
If all indicators are off, check that the power cord is connected correctly and that the power is being supplied normally.
Sometimes, when the power cord is unplugged, the [t] indicator remains lit for a short period, but this is not a fault.
: Lit : Flashing : Off : Varies according to the projector status
Status Cause Remedy or Status
Internal Error Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s"Epson Projector Contact List" p.81
Fan Error
Sensor Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s"Epson Projector Contact List" p.81
High Temp Error
(Overheating)
The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector switches to standby
mode, so check the following two points.
•Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
•If the air filter is clogged, remove the power plug from the electrical outlet, and clean or replace it.
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s"Epson Projector Contact List" p.81
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
Press [Menu] button > Extended > Operation > High Altitude Mode
Lamp Error
Lamp Failure
Check the following two points after turning off the projector and removing the power plug from the electrical outlet.
•Take out the lamp and check if it is cracked.
•Clean the air filter.
If the lamp is not cracked: Reinstall the lamp and connect the plug to an electrical outlet.
If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest
address provided in the Epson Projector Contact List.
s"Epson Projector Contact List" p.81
Reading the Indicators
17

Status Cause Remedy or Status
If the lamp is cracked: Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be
projected until the lamp is replaced.)
s"Epson Projector Contact List" p.81
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
Press [Menu] button > Extended > Operation > High Altitude Mode
Auto Iris Error
Power Err. (Ballast)
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s"Epson Projector Contact List" p.81
Filter Airflow Error Check the following two points.
•Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
•If the air filter is clogged, remove the power plug from the electrical outlet, and clean or replace it.
After checking, connect the power plug to an electrical outlet.
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s"Epson Projector Contact List" p.81
High Temp Warning This is not an abnormality. However, if the temperature rises too high again, projection stops automatically. Check the following two points.
•Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
•If the air filter is clogged, remove the power plug from the electrical outlet, and clean or replace it.
Replace Lamp Replace with a new lamp after turning off the projector and removing the power plug from the electrical outlet.
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. Replace it with a
new lamp as soon as possible.
Low Air Flow Check the following two points.
•Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
•If the air filter is clogged, remove the power plug from the electrical outlet, and clean or replace it.
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s"Epson Projector Contact List" p.81
Reading the Indicators
18

Status Cause Remedy or Status
Air Filter Notice "Time to clean the air filter. Clean or replace the air filter."is displayed. Clean the air filter after turning off the projector and removing the power
plug from the electrical outlet.
The indicators or messages regarding Air Filter Notice are displayed only when Air Filter Notice is set to On from the Configuration menu.
Press [Menu] button > Extended > Display > Air Filter Notice
a
If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or
the nearest address provided in the Epson Projector Contact List.
s"Epson Projector Contact List" p.81
Reading the Indicators
19

Installation Requirements
Warning
•A special method of installation is required when suspending the projector
from a ceiling (ceiling mount). If installation work is not carried out
correctly, the projector could fall down. This may result in injury or
accidents.
Contact your dealer or the nearest address provided in the Epson Projector
Contact List if you want to use this installation method.
s"Epson Projector Contact List" p.81
•If you use adhesives on the Ceiling mount fixing points to prevent the screws
from loosening, or if you use things such as lubricants or oils on the
projector, the projector case may crack causing it to fall from its ceiling
mount. This could cause serious injury to anyone under the ceiling mount
and could damage the projector.
When installing or adjusting the ceiling mount, do not use adhesives to
prevent the screws from loosening and do not use oils or lubricants and so
on.
•Do not cover the projector's air intake vent or air exhaust vent. If either of
the vents are covered, the internal temperature could rise and cause a fire.
a
•An optional ceiling mount is required when suspending the projector
from a ceiling.
•When mounted on a ceiling, set Inv Direction Button to On so that
the operations and movement of the [ ], [ ], [ ], and [ ]
buttons on the control panel match.
Press [Menu] button > Extended > Operation > Inv Direction
Button
The projector can be installed at the following angles.
Vertical: Can be installed at any angle in a complete 360 degrees.
Horizontal: Can be tilted within the range of expansion and contraction for
the rear feet.
s"Adjusting the Horizontal Tilt (When Setup on a Desk)" p.25
Make sure there is a gap of at least 50 cm between the wall and the air
exhaust vent and the air intake vent.
Air exhaust vent
Air intake vent
When setting up multiple projectors, make sure there is a gap of at least
50 cm between the projectors. Also, make sure the heat coming out of the
air exhaust is not taken in through the air inlet.
When installation is complete, set the Direction from the configuration
menu according to the vertical installation angle.
Press [Menu] button > Extended > Direction
Use the [ ][ ] buttons to set the projector's installation angle.
Installing the Projector
20