Epson EB-L30002U System manual

Transport and Installation Handbook

Introduction
1
About the Manuals for this Projector
The following manualsare supplied with the projector.Make sure you read the manuals thoroughly to operate
the projector correctly and safely.
Booklet (Paper) Manual
•Transport and Installation Handbook (this handbook)
Provides instructions on carrying and installing this projector safely.
Check this handbook before carrying and installing.
Contact your local dealer or the nearest address provided in the Safety Instructions.
PDF Manuals
•Safety Instructions
Provides cautionary notes on using this projector safely and information on support and service.
Make sure you check these manuals before use.
•User's Guide
Provides information on using this projector, using the Configuration menu, troubleshooting, and maintenance.
•Specifications
Provides information on the projector specifications, external dimensions, supported lenses, and so on.
For More Information
http://epson.sn

Introduction
2
Notations Used in This Guide
The documentation and the projector use graphical symbols to show how to use it correctly and safely to
avoid personal injury, injury to others, and damage to property.
The indications and their meaning are as follows. Make sure you understand them properly before reading
the guide.
Symbol Meaning
Warning This symbol indicates information that, if ignored, could possibly result in serious personal
injury or even death due to incorrect handling.
Caution This symbol indicates information that, if ignored, could possibly result in personal injury or
physical damage due to incorrect handling.
Indicates Prohibited Actions Indicates Instructions that Must be Followed
Prohibited Contact pro-
hibition
Usage near
water pro-
hibited
Instructions Instructions
that must be
followed
Disconnect
plug from
electrical out-
let
Contact a
qualified
technician

Contents
3
Introduction
About the Manuals for this Projector . . . 1
Booklet(Paper)Manual ...................1
PDFManuals ........................... 1
ForMoreInformation ..................... 1
NotationsUsedinThisGuide ........... 2
Transport and Installation
Handbook
Notes on Carrying and Transporting
....................................... 4
WhenCarryingWithoutPacking ............. 4
WhenPackingandTransporting ............. 5
Notes on Installation .................. 6
NotesontheInstallationEnvironment ......... 6
NotesonInstalling ....................... 7
CautionsonLifting ...................... 10
NotesonConnections...................12
AttachingtheLensUnit .................. 13

Transport and Installation Handbook
4
Notes on Carrying and Transporting
Caution
Before carrying this projector, make sure you turn it off and disconnect all
cables.
When Carrying Without Packing
Note the following points when moving the projector by hand or by using a forklift to a close location without
packing it up.
Caution
This projector is heavy and should be carried by at least four people.
When an optional lens is attached, attach the lens cap for the lens unit being
used.
When lifting this projector with a forklift, do not insert the fork from the
front of the projector (the lens side). Otherwise, the lens unit or the projector
could be damaged.
Insert the fork from the rear or the side.

Transport and Installation Handbook
5
When Packing and Transporting
Note the following points when packing up this projector and transporting it on a track and so on.
Caution
Before packing, remove the lens unit from the projector, and attach the
protective cap. If you have used lens shift to move the lens position, move
the lens to the home position and then remove the lens unit.
Enclose the projector securely in packaging material to protect it from
shock, and place it into a strong container.
This projector is precision equipment. A qualified technician such as the
carrier company must transport the projector with caution.

Transport and Installation Handbook
6
Notes on Installation
Notes on the Installation Environment
Warning
Do not use or install the projector where it may be subject to water or rain,
or high humidity, such as outdoors, in a bathroom, or shower room, and so
on.
Otherwise, it could cause a fire or electric shock.
Do not place flammable objects in front of the lens.
If you set the schedule to turn on the projector automatically, any flammable objects placed
in front of the lens could cause a fire.
Caution
Check the following points before installing.
•
Make sure the location is not subject to vibrations or shocks.
•
Make sure the location does not shake and is not tilted at an angle.
•
Makes sure there are no high-voltage lines or magnetic devices in the surrounding environ-
ment.
Do not use or store the projector in a location that is subject to extreme
temperatures.
Also, avoid sudden temperature changes.
Make sure you use or store the projector in a place that is within the following operating or
storage temperature ranges.
•
Operating Temperature
0 to +50°C (Altitude of 0 to 2,286 m, no condensation)
0 to +45°C (Altitude of 2,287 to 3,048 m, humidity of 20% to 80%, and no condensation)
•
Storage temperature
-10 to +60°C (No condensation)
Do not install the projector in direct sunlight.
If the projector is in direct sunlight, the internal temperature increases, which could cause
parts such as the surface of the projection lens or the built-in camera to deteriorate.

Transport and Installation Handbook
7
Caution
When installing the projector in an environment in which a high-powered
laser beam is being used, make sure it is installed so that the laser beam
does not hit the surface of the projector's projection lens or the built-in
camera.
If the laser beams through the surface of the projection lens or the built-in camera, block the
laser beam with non-permeable or incombustible aluminum foil or metal plates such as iron
to protect the projection lens and the built-in camera. You canalso use the projector's Shutter
function to prevent the LCD panel from being damaged by laser light.
When using the projector in smoky environments such as at events and so
on, make sure you replace the air filter after approximately 240 hours of
use. (This is a guideline when using the projector in an environment with
an atmospheric concentration of ondina oil of approximately
0.000000013%. The air filter replacement time may be shorter depending
on the operating environment.)
Using the projector in a smoky environment may cause the filter's dust collection function
to decline and dust may adhere to the inside of the projector or the power supply; this may
cause a malfunction to occur.
Do not install the projector in an airtight location.
Heat exhausted from the projector will become trapped in the location which could cause
the projector to malfunction. When the projector is installed in an enclosed location so that
it cannot be seen, make sure the location is not airtight and that it can be ventilated and the
temperature can be controlled.
Notes on Installing
The projector can be installed at any angle. There is no vertical or horizontal limit to how the projector can
be installed.
You can install the projector in a portrait orientation by attaching the carrying handles to the top and bottom
of the projector. You can remove the feet from the projector and attach them to the carrying handle.

Transport and Installation Handbook
8
Warning
You may need dedicated installation mounts to tilt and install the projector.
Contact a specialist and prepare the mount.
•
Plan so that the mount does not fall.
•
Make sure the mount is strong enough to support the projector.
•
When attaching a mount to the projector, secure the mount with bolts using the handle
securing section (6 points) on the top or base of the projector.
Since special techniques are required to install the projector on a ceiling
(ceiling mount) or in a high location, make sure you contact a professional.
If installation work is not carried out correctly, the projector could fall down. This may result
in injury or accidents.
Note the following points when installing so that the projector's air intake
vent or air exhaust vent are not covered.
If either of the vents is covered, the internal temperature could rise and cause a fire.
•
Make sure you secure the following space around the projector.
500mm
500mm
500mm
•
When setting up multiple projectors, make sure there is a gap of at least 200 mm between the
projectors.
200mm
•
Make sure you secure the following space when installing with the air intake vent underneath.
•
A gap of at least 100 mm between the installation surface and the air intake vent.
•
A space of 800 x 350 mm around the entrance of the air intake vent.
100mm
800mm
350mm

Transport and Installation Handbook
9
Caution
Note the following points when installing a projector directly on top of
another. This projector can be installed on top of another projector that has
the carrying handles attached to the top.
•
Do not stack three or more projectors (you can stack up to two projectors).
•
Install the feet in the indentations on the top at the four corners.
•
Do not remove the feet on the bottom of the projector.
Except for the projector's parts, do not place anything on the projector.