Epson PowerLite 1970W Specification sheet

Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Note: Availability of models varies by country.
Connect the projector
Choose from the following connections. See the sections below or the online
User’s Guide for details.
Computer
VGA cable
USB cable
HDMI cable
USB port
Connect the square end of a USB cable to the projector’s USB-B (square) port.
Connect the flat end of the cable to any USB port on your computer.
Windows®2000 SP4 or later: After turning on the projector, follow
the on-screen instructions to install the Epson®USB Display software
(EMP_UDSE.EXE; only on first connection). If the software screen does
not display automatically, open My Computer or Computer, then
double-click EPSON_PJ_UD.
OS X 10.5.8 or higher: After turning on the projector, the setup folder for
USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Computer port
Connect one end of a VGA cable to the projector’s Computer1 or
Computer2 port, and the other end to your computer’s monitor port. If
you are using a laptop, switch it to external display (see “Troubleshooting”).
You can also connect an audio cable.
HDMI port
Connect one end of an HDMI cable to the projector’s HDMI1 or HDMI2 port
and the other end to an HDMI port on your computer.
Wired network
You can connect the projector to your network using an Ethernet cable. See
“Project over a wired network” for more information.
Video device
Connect up to 5 video devices and use the Source Search button on the
projector or remote control to switch between them.
RCA video cable (composite video)
Component video to VGA cable
Audio cable
Audio cable
HDMI cable
Mobile media device
Connect tablets, smartphones, and other devices that support the MHL™
standard to the HDMI1/MHL port.
MHL cable
Devices that support an MHL connection include the Samsung™ Galaxy Note
II™ and the Roku®Streaming Stick™. Some devices may require an adapter or
may not require an MHL cable. Not all features or functions may be supported.
Check your device’s documentation for more information.
Camera, USB device, or Epson DC-06 document camera
Connect a digital camera, USB flash drive, USB storage device, or Epson DC-06
document camera to the projector’s USB-A (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you
can use the projector’s PC Free feature to project images. You can also connect
other Epson document cameras to the projector. See the online User’s Guide
for details.
External monitor and external speakers
You can also connect an external monitor and external speakers to your
projector to enhance your presentations. See the online User’s Guide for details.
Turn on your equipment
1Turn on your computer or video source.
2Plug in the projector. The power light on the projector turns blue.
3Open the A/V Mute slide all the way.
4
Press the power button on the projector or remote control. The
projector beeps, the Status light flashes blue, and then stays on.
Note: To shut down the projector, press the power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
5The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select
Extended and press . Select Language and press . Select your
language and press .Press the Menu button to exit the menu system.
Adjust the image
1If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3Turn the zoom ring to reduce or enlarge the image.
W T
4Turn the focus ring to sharpen the image.
5Your projector automatically adjusts images that look like or ,
but if necessary you can press the or buttons on the projector to
correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which
source to display
Get solutions to
common problems
Navigate projector
menus
Turn projector
on and off
Access projector
menus
Turn off projector
display
For more information on using the remote control, see the online
User’s Guide.
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11n,
802.11g, or 802.11b wireless network. Your computer must have a wireless
card or built-in wireless interface, and be running Windows 8.x, Windows 7,
Windows Vista®, Windows XP Professional x64, Windows XP, or Windows 2000,
or OS X 10.5.8 to 10.9.
1
To install the optional wireless LAN module, open the air filter cover.
2Remove the screw securing the wireless LAN module stopper, then
remove the stopper.
3Install the wireless LAN module.
PowerLite®1970W/1975W/1980WU/1985WU

Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Note: Availability of models varies by country.
Connect the projector
Choose from the following connections. See the sections below or the online
User’s Guide for details.
Computer
VGA cable
USB cable
HDMI cable
USB port
Connect the square end of a USB cable to the projector’s USB-B (square) port.
Connect the flat end of the cable to any USB port on your computer.
Windows®2000 SP4 or later: After turning on the projector, follow
the on-screen instructions to install the Epson®USB Display software
(EMP_UDSE.EXE; only on first connection). If the software screen does
not display automatically, open My Computer or Computer, then
double-click EPSON_PJ_UD.
OS X 10.5.8 or higher: After turning on the projector, the setup folder for
USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Computer port
Connect one end of a VGA cable to the projector’s Computer1 or
Computer2 port, and the other end to your computer’s monitor port. If
you are using a laptop, switch it to external display (see “Troubleshooting”).
You can also connect an audio cable.
HDMI port
Connect one end of an HDMI cable to the projector’s HDMI1 or HDMI2 port
and the other end to an HDMI port on your computer.
Wired network
You can connect the projector to your network using an Ethernet cable. See
“Project over a wired network” for more information.
Video device
Connect up to 5 video devices and use the Source Search button on the
projector or remote control to switch between them.
RCA video cable (composite video)
Component video to VGA cable
Audio cable
Audio cable
HDMI cable
Mobile media device
Connect tablets, smartphones, and other devices that support the MHL™
standard to the HDMI1/MHL port.
MHL cable
Devices that support an MHL connection include the Samsung™ Galaxy Note
II™ and the Roku®Streaming Stick™. Some devices may require an adapter or
may not require an MHL cable. Not all features or functions may be supported.
Check your device’s documentation for more information.
Camera, USB device, or Epson DC-06 document camera
Connect a digital camera, USB flash drive, USB storage device, or Epson DC-06
document camera to the projector’s USB-A (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you
can use the projector’s PC Free feature to project images. You can also connect
other Epson document cameras to the projector. See the online User’s Guide
for details.
External monitor and external speakers
You can also connect an external monitor and external speakers to your
projector to enhance your presentations. See the online User’s Guide for details.
Turn on your equipment
1Turn on your computer or video source.
2Plug in the projector. The power light on the projector turns blue.
3Open the A/V Mute slide all the way.
4
Press the power button on the projector or remote control. The
projector beeps, the Status light flashes blue, and then stays on.
Note: To shut down the projector, press the power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
5The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select
Extended and press . Select Language and press . Select your
language and press .Press the Menu button to exit the menu system.
Adjust the image
1If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
3Turn the zoom ring to reduce or enlarge the image.
W T
4Turn the focus ring to sharpen the image.
5Your projector automatically adjusts images that look like or ,
but if necessary you can press the or buttons on the projector to
correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which
source to display
Get solutions to
common problems
Navigate projector
menus
Turn projector
on and off
Access projector
menus
Turn off projector
display
For more information on using the remote control, see the online
User’s Guide.
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11n,
802.11g, or 802.11b wireless network. Your computer must have a wireless
card or built-in wireless interface, and be running Windows 8.x, Windows 7,
Windows Vista®, Windows XP Professional x64, Windows XP, or Windows 2000,
or OS X 10.5.8 to 10.9.
1
To install the optional wireless LAN module, open the air filter cover.
2Remove the screw securing the wireless LAN module stopper, then
remove the stopper.
3Install the wireless LAN module.
PowerLite®1970W/1975W/1980WU/1985WU

6 Select the Wired LAN menu and press .
7 Choose IP Settings and press .
8
If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
9
To prevent the IP address from appearing on the network standby screen,
set the IP Address Display setting to Off.
10
When you are finished, select Complete and press , then press
again to save your settings.
11 Press the Menu button to exit the menu system.
12 See “Install network software” for additional instructions.
Mobile device
To project from an iOS or Android™ device,
download and install the Epson iProjection™
app. Visit epson.com/projectorapp (U.S.)
or epson.ca/projectorapp (Canada) for
more information.
Install network software
Install the EasyMP®Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, click the icon
on your desktop to access the online EasyMP Network Projection Operation
Guide (requires an Internet connection). If you don’t see the EasyMP Network
Projection Guide icon, you can install it from the projector CD or go to the
Epson website, as described on the right.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install a link to the downloads page from the projector CD or go to the
Epson website, as described on the right.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•Make sure the power and Status lights on the projector are blue and not
flashing, and the A/V Mute slide is open.
•Press the Source Search button on the projector or the remote control to
switch to the correct image source, if necessary.
•If you’re using a Windows laptop, press the function key on your keyboard
that lets you display on an external monitor. It may be labeled CRT/LCD or
have an icon such as . You may have to hold down the Fn key while
pressing it (such as Fn + F7). Wait a moment for the display to appear.
•If you’re using a Mac laptop, open System Preferences and select
Displays. Click the Arrangement tab, and select the Mirror Displays
check box.
4Replace the wireless LAN module stopper and secure it using the screw
you removed.
5Close the air filter cover.
6
To configure your projector for your wireless network, do one of the
following:
• If you’re using the optional Quick Wireless Connection USB key, insert
it into the projector’s USB-A port, look for the displayed message,
remove the key, and connect it to a USB port on your computer.
Follow the on-screen instructions to install the driver, then run your
presentation. For details, see the online User’s Guide.
•If you’re not using the key, continue with the steps below.
7Press the Menu button on the remote control, select the Network menu,
and press .
8Choose Network Configuration and press .
9Select the Wireless LAN menu and press .
10 Choose Connection Mode, press , select Quick (for a direct
connection to a computer, tablet, or smartphone) or Advanced (for
a connection to a router or access point), then press again. When
you’re finished, press Esc to return to the Wireless LAN menu.
11 If you chose the Advanced connection mode, select SSID, press and
enter your network name (SSID) on the screen that appears.
•To select a number or character, use the arrow buttons on the remote
control to highlight it, then press .
•To switch between uppercase and lowercase letters, select CAPS and
press .
•To change the displayed symbols, select SYM1 or SYM2 and
press .
When you’re finished entering the SSID, select Finish and press .
EPSON, EasyMP, and PowerLite are registered trademarks, Epson iProjection is a trademark, and EPSON Exceed
Your Vision is a registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson
America, Inc.
Mac and OS X are trademarks of Apple, Inc., registered in the U.S. and other countries.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2014 Epson America, Inc., 5/14
Printed in XXXXXX CPD-41055
12 If you chose the Advanced connection mode, select IP settings and
press .
If your network assigns addresses automatically, turn on DHCP. If not,
turn off DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the arrow buttons on the remote control to
highlight a number, then press the button. When you’re finished
entering an address, highlight Finish, then press . Press Esc.
13 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and IP Address Display
settings to Off.
14 When you’re finished selecting settings in the Wireless LAN menu,
press Esc.
15 If you are connecting the projector to a secure network, select the
Security menu and press . Then select settings and press Esc when
you’re finished.
16 Select Complete and press, then select Yes and pressagain to
save your settings.
17 See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1 Plug in and turn on the projector.
2
Press the Menu button on the remote control, select the Network menu,
and press .
3 Select Network Configuration and press .
4 Select the Basic menu and press .
5
Select the Projector Name setting and enter a name (up to 16 characters
long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
Where to get help
Manuals
For more information about using the projector, click the icons on your
desktop to access the online manuals (requires an Internet connection). If you
don’t have icons to the manuals, you can install them from the projector CD or
go to the Epson website, as described below.
Telephone support services
To use the Epson®PrivateLine®Support service, call [phone]. This service
is available for the duration of your warranty period. You may also speak with
a support specialist by calling [phone] (U.S.) or [phone] (Canada).
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and
7 am to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to
change without notice. Toll or long distance charges may apply.
Internet support
Visit epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to
common problems. You can download utilities and documentation, get FAQs
and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates and exclusive offers. You can use the CD
included with your projector or register online at www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized reseller.
To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can
purchase online at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).

6 Select the Wired LAN menu and press .
7 Choose IP Settings and press .
8
If your network assigns addresses automatically, select IP Settings and
turn on the DHCP setting. If not, turn off the DHCP setting and enter
the projector’s IP Address, Subnet Mask, and Gateway Address,
as needed.
9
To prevent the IP address from appearing on the network standby screen,
set the IP Address Display setting to Off.
10
When you are finished, select Complete and press , then press
again to save your settings.
11 Press the Menu button to exit the menu system.
12 See “Install network software” for additional instructions.
Mobile device
To project from an iOS or Android™ device,
download and install the Epson iProjection™
app. Visit epson.com/projectorapp (U.S.)
or epson.ca/projectorapp (Canada) for
more information.
Install network software
Install the EasyMP®Network Projection software on each computer that will
project over the network. Use the CD labeled Epson Projector Software to
install the program.
For instructions on installing and using your network software, click the icon
on your desktop to access the online EasyMP Network Projection Operation
Guide (requires an Internet connection). If you don’t see the EasyMP Network
Projection Guide icon, you can install it from the projector CD or go to the
Epson website, as described on the right.
To monitor and control your projector over the network, download and install
the EasyMP Monitor software and manual from the Epson support web site.
You can install a link to the downloads page from the projector CD or go to the
Epson website, as described on the right.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
•Make sure the power and Status lights on the projector are blue and not
flashing, and the A/V Mute slide is open.
•Press the Source Search button on the projector or the remote control to
switch to the correct image source, if necessary.
•If you’re using a Windows laptop, press the function key on your keyboard
that lets you display on an external monitor. It may be labeled CRT/LCD or
have an icon such as . You may have to hold down the Fn key while
pressing it (such as Fn + F7). Wait a moment for the display to appear.
•If you’re using a Mac laptop, open System Preferences and select
Displays. Click the Arrangement tab, and select the Mirror Displays
check box.
4Replace the wireless LAN module stopper and secure it using the screw
you removed.
5Close the air filter cover.
6
To configure your projector for your wireless network, do one of the
following:
• If you’re using the optional Quick Wireless Connection USB key, insert
it into the projector’s USB-A port, look for the displayed message,
remove the key, and connect it to a USB port on your computer.
Follow the on-screen instructions to install the driver, then run your
presentation. For details, see the online User’s Guide.
•If you’re not using the key, continue with the steps below.
7Press the Menu button on the remote control, select the Network menu,
and press .
8Choose Network Configuration and press .
9Select the Wireless LAN menu and press .
10 Choose Connection Mode, press , select Quick (for a direct
connection to a computer, tablet, or smartphone) or Advanced (for
a connection to a router or access point), then press again. When
you’re finished, press Esc to return to the Wireless LAN menu.
11 If you chose the Advanced connection mode, select SSID, press and
enter your network name (SSID) on the screen that appears.
•To select a number or character, use the arrow buttons on the remote
control to highlight it, then press .
•To switch between uppercase and lowercase letters, select CAPS and
press .
•To change the displayed symbols, select SYM1 or SYM2 and
press .
When you’re finished entering the SSID, select Finish and press .
EPSON, EasyMP, and PowerLite are registered trademarks, Epson iProjection is a trademark, and EPSON Exceed
Your Vision is a registered logomark of Seiko Epson Corporation. PrivateLine is a registered trademark of Epson
America, Inc.
Mac and OS X are trademarks of Apple, Inc., registered in the U.S. and other countries.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2014 Epson America, Inc., 5/14
Printed in XXXXXX CPD-41055
12 If you chose the Advanced connection mode, select IP settings and
press .
If your network assigns addresses automatically, turn on DHCP. If not,
turn off DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the arrow buttons on the remote control to
highlight a number, then press the button. When you’re finished
entering an address, highlight Finish, then press . Press Esc.
13 To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and IP Address Display
settings to Off.
14 When you’re finished selecting settings in the Wireless LAN menu,
press Esc.
15 If you are connecting the projector to a secure network, select the
Security menu and press . Then select settings and press Esc when
you’re finished.
16 Select Complete and press, then select Yes and pressagain to
save your settings.
17 See “Install network software” for additional instructions.
Project over a wired
network
Follow the steps here to configure your projector for your wired network using
the projector’s menu system.
1 Plug in and turn on the projector.
2
Press the Menu button on the remote control, select the Network menu,
and press .
3 Select Network Configuration and press .
4 Select the Basic menu and press .
5
Select the Projector Name setting and enter a name (up to 16 characters
long) to identify your projector over the network.
Use the displayed keyboard to enter characters. Press the arrow buttons
on the remote control to highlight the characters and press to select
them.
Note: See the online User’s Guide for information on adding passwords.
Where to get help
Manuals
For more information about using the projector, click the icons on your
desktop to access the online manuals (requires an Internet connection). If you
don’t have icons to the manuals, you can install them from the projector CD or
go to the Epson website, as described below.
Telephone support services
To use the Epson®PrivateLine®Support service, call [phone]. This service
is available for the duration of your warranty period. You may also speak with
a support specialist by calling [phone] (U.S.) or [phone] (Canada).
Support hours are 6 am to 8 pm, Pacific Time, Monday through Friday, and
7 am to 4 pm, Pacific Time, Saturday. Days and hours of support are subject to
change without notice. Toll or long distance charges may apply.
Internet support
Visit epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to
common problems. You can download utilities and documentation, get FAQs
and troubleshooting advice, or e-mail Epson.
Registration
Register today to get product updates and exclusive offers. You can use the CD
included with your projector or register online at www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see the online User’s Guide.
You can purchase screens or other accessories from an Epson authorized reseller.
To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can
purchase online at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).