Epson TM-P60II User manual

This guide presents important information intended to ensure safe and effective use of this product.
Read this guide carefully and store it in an accessible location.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation.
Canada
This device conforms to IC, Low Power License-Exempt Radio Communication Devices (RSS-210).
The information such as Certification No., Model Name, and Manufacturer Name are described on
the surface of the module.
Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired
operation of this device.
Caution: Exposure to Radio Frequency Radiation
To comply with IC RF exposure compliance requirements, this device must not be co-located or
operating in conjunction with any other antenna or transmitter.
Notes on Usage
This Model can be Used Only in the Countries/Areas Listed Below:
Austria, Belgium, Bulgaria, Czech, Denmark, Estonia, Finland, France, Germanym Greece, Hungary,
Ireland, Italy, Latvia, Lithuania, Luxemburg, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland, UK, U.S.A, Canada, Australia, New Zealand and
Hong Kong*
(*: Receipt model only)
Italy
In Italy, if used outside of own premises, general authorization is required.
Timing of cutting off connection
If data transfer from an application of the host has already been completed, data might remain in the
printer internal buffer. As such data remaining in the buffer might be lost when the connection is cut
off, use the status and similar functions to check that transmitted data has been completely printed
when printing or cutting off the wireless connection.
Bluetooth
®
Interface Model
412538701
Printed in China

Notes on Using with iOS-equipped Devices
Note the following points when using this product with iOS-equipped devices.
Depending on the iOS specifications, print data may be deleted if it is sent while the printer is not
ready to print.
The printer is unable to print in cases such as
• when the roll paper cover is open.
• when the paper is out.
• when the printer is waiting for a label to be removed. (Peeler model only)
RF Module
This equipment contains the following wireless module.
Default setting
Default setting of the printer is as follows.
*
"xxxxxx" is the last six digits of the product serial number.
Setting to automatically reestablish the connection
1. Install the roll paper.
2. Close the roll paper cover and the peeler cover (Peeler model only).
3. While pressing the Feed button, turn on the printer. (Keep pressing the button until the printer
starts printing.)
The printer starts printing the current status of the printer on the roll paper.
4. Press the Feed button. (Keep pressing the button until the printer starts printing.)
The printer starts printing instructions.
5. After the printing has been completed, press the Feed button 4 times.
6. Press the Feed button again. (Keep pressing the button until the printer starts printing.)
The printer starts printing instructions (Wireless Module Setup).
7. Press the Feed button 2 times.
8. Press the Feed button again. (Keep pressing the button until the printer starts printing.)
The printer starts printing instructions (Bluetooth Setting).
9. Press the Feed button.
10. Press the Feed button again. (Keep pressing the button until the printer starts printing.)
The printer starts printing instructions (Auto Re-Connect iOS).
11. <Enabling> Press the Feed button.
<Disabling> Press the Feed button 2 times.
12. Press the Feed button again. (Keep pressing the button until the printer starts printing the
following message.)
"Please release the Feed button."
The printer restarts.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
Seiko Epson Corporation is under license. Other trademarks and trade names are those of their respective owners.
Copyright © 2013 by Seiko Epson Corporation
Manufacturer: Fujitsu Component Limited
Model Name: MBH7BTZ50
Product Name: Bluetooth Module
Device name: TM-P60II_xxxxxx
*
Passkey: 0000 (four zeros)
Automatically reestablish the connection: Enabling