EPV Twilight Portable Series User manual

Rev.03242022JA www.epvscreens.com 1 | S\N: 203E +
Twilight Electric Series
Outdoor Electric Projection Screen
For 100” and 120” models
User’s Guide
_________________________________________________________
Thank you for choosing the Twilight Electric projection screen! Please read through this user guide before utilizing
the screen. Correct usage and maintenance will ensure a long product life.
Product Description:
The Twilight Electric is an outdoor projector screen for wall and patio installations that brings media room quality
to your outdoor spaces. Its sleek aluminum casing beautifully accessorizes your backyard, patio, pool deck or
anywhere a gathering for evening movie time is appropriate.
Outdoor Projection Screen Disclaimer
Never leave your projection screen out and exposed to direct sunlight. Regardless of screen brand, prolonged
exposure to the sun’s ultraviolet radiation degrades the chemical bonds causing the material to ultimately
decompose. Photo degradation first causes the material to lose its theater-grade reflective qualities. Eventually
nature will destroy even synthetic materials. For this reason, the Twilight Electric has a retractable design that
allows the material to be drawn up into its protective casing to be shielded from solar radiation.
Care & Use Instructions
◆Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points
below to prevent that from occurring:
1. Do not touch the projection surface with your hands
2. Do not write or draw on the projection surface
3. Do not use fingers or sharp objects to point on the projection surface; this will damage the screen material.
4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or alcohol.
5. Use clean water when dampening the cleaning cloth and do not rub against the material to clean it.
◆To avoid damage and injury, the screen should only be operated by adults.

Rev.03242022JA www.epvscreens.com 2 | S\N: 203E +
Understanding the Ingress Protection Rating IP33
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, direct connection to a properly grounded power source is advised.
•The power outlet supplying power to the unit should be close to the unit and easily accessible.
•Do not install the unit on uneven or inclined surfaces.
•Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle.
•Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short circuit.
•There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself. No one
except authorized technicians can open and make repairs to this unit.
•Make sure the power source this unit is connected to has a continuous power flow.
•If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to avoid
overheat.
•Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
•Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
•Avoid direct Sunshine, rain shower and moisture.
•Keep away from fire sources and high temperature to prevent this device from overheating.
•Cut off the power supply first before transportation or maintenance.
•Fully disconnect from the power supply when the unit is not in use for a long period of time, as should be
done with any other electric household appliance.
•To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious
damage or if there are any evident broken parts.

Rev.03242022JA www.epvscreens.com 3 | S\N: 203E +
WARNING
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop in the
roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer. Please
contact Customer Service for any questions.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a installation. If this equipment causes
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures.
✓Reorient or relocate the receiving antenna of the device which may be causing the interference.
✓Increase the separation between the screen and the device’s receiver.
✓Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles
such as dust, sawdust, and/or liquids.
NOTE
Wall screws included with this product are complimentary and may not be adequate for all mounting surfaces.
Consult with a professional installer or hardware store for proper mounting screws and anchors.
Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the
viewing surface will not cause the casing to become loose or fall. The installer must ensure that the fasteners used
are of adequate strength and suitable for the installation location.
Hardware Parts List for Twilight Electric Series
A. Mounting Bracket
x2pcs
B. M10 Anchor and
M4x50 Screw x4pcs
C. M8x35 Anchor and
M4x35 Screw x4pcs
D. Suspended Ceiling
Bracket Connector x2pcs
E. M5x15 Screw&
Bolt x4pcs
G. Magnetic weight
bar bracket x2pcs
H. Curved Stake
x2pcs
I. Snap link x2pcs
J. Elastic String x2pcs
K. Bubble leveler
x1pc

Rev.03242022JA www.epvscreens.com 4 | S\N: 203E +
INSTALLATION INSTRUCTIONS
Flush Mount to the Wall
1. Mark the location of where the screen is to be installed, drill your holes and insert the M10Anchors (B).
2. Install the Mounting Brackets (A) to the wall and secure with the M4x50 Screws (B).
3. Attach the screen to the Mounting Brackets (A) by inserting the top of the case to Fix Plate 1 and securing the
back of the case to Fix Plate 2. Make sure the case slots are securely attached to the mounting brackets.
Mounting Bracket Mounting Bracket
Fix Plate 1 Fix Plate 2
Case Slot 2 Screen Case
Mounting bracket
Fix Plate 1
M4x50 Screw
Mounting Bracket
Fix Plate 2
Mounting Bracket
Wall
Anchor
Mounting Bracket Case Slot 1

Rev.03242022JA www.epvscreens.com 5 | S\N: 203E +
Flush Mount to the Ceiling
Note: Please make sure the Mounting Bracket (A) is close to the wall when you install the screen on the ceiling.
This is to ensure the weight bar aligns with the magnetic bottom bracket when it comes down.
1. Mark the location of where the screen is to be installed, drill your holes, and insert the M10Anchors (B).
2. Install the Mounting Brackets (A) to the ceiling and secure with the M4x50 Screws (B).
Ceiling M10 Anchor
Mounting Bracket Fix Plate 1
Mounting Bracket M4x50 Screw
3. Attach the screen to the Mounting Bracket (A) by inserting the top of the case to Fix Plate 1 and securing the
back of the case to Fix Plate 2. Make sure the case slots are securely attached to the Mounting Bracket (A).
Suspended Ceiling using Chains (additional hardware required)
1. You can also hang the screen on a ceiling by using chains (not included).
2. Connect the Suspended Ceiling Bracket Connector (D) to the Mounting Bracket (A) and secure with the
M5x15 Screws & Bolts (E).
M5x15 Bolt (E) Suspended Ceiling Bracket Connector
(D)
Mounting Bracket
(A)
3. Insert chains (not included) through the loop holes of the Suspended Ceiling Bracket Connector (D).
Suspended Ceiling Bracket Connector
(D)
Fix Plate 2
Mounting Bracket Fix Plate
Fix Plate 1
M5x15 Screw (E)

Rev.03242022JA www.epvscreens.com 6 | S\N: 203E +
Screen removal from the Mounting Brackets
Pull down on the Mounting Bracket Release
Tab and remove the bottom case away from
the wall/ceiling followed by the top of the case.
`
Twilight Electric Control System and Operation
Twilight Electric Series Controls
A. RF Remote Control x1 pc (Battery built-in)
B. Wireless trigger x1pc
Screen operation
Electric Current: 110v.
1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen has power, you’ll be able to control it using any of the 2 methods described below.
2 ways to control your Twilight Electric Screen
1. RF Remote Control (Item A): The radio waves eliminate the need for a direct line of sight.
Radio Frequency (RF) Remote Synchronization Instructions
1. Make sure the screen’s power cable is not plugged into a power outlet (If so, then unplug it).
2. Press and HOLD the UP button on the RF remote until you see the flashing light turn solid. (See diagram
above)
3. While holding the UP button, plug the screen’s power cable into the power outlet. The screen will drop
slightly (you may hear a beep) indicating it has entered pairing mode.
4. Release the UP button for 3 seconds, then press UP button again until you see the flashing light turn
solid (the screen will go up and down slightly).
5. You should now be able to control your electric screen with the RF remote control.
6. If unsuccessful repeat from Step 1.
Note: The beep(s) the screen produces are very faint. It may be difficult to hear, if more than 5 feet away from
the screen.
UP
STOP
DOWN

Rev.03242022JA www.epvscreens.com 7 | S\N: 203E +
2. Wireless trigger (Item B): The wireless trigger allows your screen to synchronize its drop/ rise operation with the
projector’s power cycle.
Wireless Trigger Set Up Instructions
A. Wireless trigger and Twilight Electric projection screen set up [CODE] button:
1. Unplug the Power Cable attached to your motorized Elite Screen from the wall.
2. Connect the Projector’s Power Cable to the wireless trigger, then plug the cable into a nearby power outlet.
3. Locate the [CODE] button on the back of the trigger, then, using a small pin, press and hold the [CODE]
button.
4. When you see the LED indicator light flashing rapidly, plug the screen’s power cord into a nearby outlet.
The screen will go up and down slightly. Release the [CODE] button at this point (you may hear a beep
sound from the screen).
5. Within 3 seconds after releasing the [CODE] button, press and hold the [CODE] button again until you see
the LED indicator light flashing rapidly (the screen will go up and down slightly), this means the
synchronization (pairing) process is successful.
6. If unsuccessful repeat from Step 1.
B. Wireless trigger and projector set up [SET] button:
1. Plug the wireless trigger’s IEC cable into the projector’s power receptacle.
2. Power ON the projector. The screen should drop automatically.
3. Locate the [SET] button on the back of the trigger, then (using a small pin) press and hold the [SET] button
for about 3 seconds until LED indicator light flashes and you hear a beep sound.
4. Turn off the projector within 10 seconds after the LED indicator light emits a flash and a beep.
5. At this step in the process, the trigger will record the running current of the projector when it is turned off,
and then the process is completed.
6. Power ON the projector. The screen should drop automatically.
7. Power OFF the projector. The screen should retract automatically.
8. If unsuccessful repeat from Step 1.
Projector
[SET] Button
[CODE] Button:
For programming the receiver
[SET] Button:
For setting the trigger feature
[CODE] Button
LED indicator light
AC power input
120VAC 60Hz
(Optional 220VAC 50Hz)
Note
➢When powering off the projector,
assure it is completely powered off
(ex, fan off), then the screen will
retract automatically
➢If the motorized screen does not
automatically drop or retract, repeat
the process from Step 1.
Back of wireless trigger

Rev.03242022JA www.epvscreens.com 8 | S\N: 203E +
Magnetic bottom bracket Installation
1. After the screen is plugged in to a power outlet, press the DOWN button on the RF remote control (F). Install
the magnetic bottom bracket (G) so that the weight bar sleeve cradles inside (see picture below).
Note: The screen should deploy straight down and align with the magnetic bottom bracket (G). Once the weight
bar is cradled inside the magnetic bracket, the screen will be from movement.
2. Mark the drill-hole area of where the bracket is to be installed with a marker or pencil.

Rev.03242022JA www.epvscreens.com 9 | S\N: 203E +
3. Raise the screen UP using the RF remote control. Next, drill holes to insert the M8 x35 Anchor (C) if installing
to a dry wall. Then affix the magnetic bottom bracket (G) on the marked location and secure it with an M4x35
Screw(C).
4. Drop the screen DOWN using the RF remote, see if the position of the magnetic bottom bracket (G) is correct
or not. Reposition the magnetic bottom bracket if needed.
How to ground the screen
1. Attach the Hook (I) into the Iron Ring, and join the Hook (I) and Curved Stake (H)using the
Elastic String (J),
2. Drive the Curved Stake (H) to the ground and stretch the Elastic String (J)in the direction of the
Curved Nail (H) to secure screen to the ground and supply adequate tension to the screen.
For more information, technical support or your local EPV Screens contact,
please visit www.epvscreens.com
M8 x 35 Anchor
Wall
The magnetic
bottom bracket
M4x35 Screw
Elastic
String
Curved
Stake
Iron Ring
Ground
Hook