EPV Power Max Tension ISF Series User manual

Rev.02142023JA 1 www.epvscreens.com
Power Max Tension ISF Series
Electric Wall/Ceiling Tab-Tensioned Projection Screen
User’s Guide –E Type (RC1)
V1
Visit www.epvscreens.com for the latest updated version
__ ____ _________
Product Description
The Power Max Tab-Tension ISF Series is an electric projection screen that is designed for rooms with controlled room
lighting. The matte white projection surface is EPV’s ChromaWhite ISF which is ISF Certified by the renowned Imaging
Science Foundation for producing accurate colors in a dark room environment.
Screen Maintenance
Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection image.
For optimal results we advise to pay attention to the following instructions.
•Use a dry microfiber cloth or soft brush to remove dust from the screen’s surface.
•When cleaning, use a damp microfiber cloth with warm water to remove any marks.
•Never rub or apply pressure when cleaning the surface.
•Don’t point to the screen material with a fingertip or other sharp objects to prevent damage to the material.
•Don’t scratch the material, as it will leave permanent markings on the screen’s surface.
•Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such chemicals
will permanently damage the screen.
Notes: The following precautions should always be followed to avoid damaging the material, which is not covered
under warranty.
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
CAUTION: Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will likewise void your warranty. For more information, please contact our Technical Support
Department at techsuppor[email protected]m.
•Please retain this user’s guide for future reference.
•To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the manufacturer.
•Handle the unit carefully during transportation to avoid any damages.
•To ensure safe and reliable operation, make sure the power connection is secure.
•The power source should be close to the unit and easily accessible.
•Do not install the unit on uneven, or inclined surfaces;
•To avoid electrical shock or product damage, do not install this device in a damp place.
•Do not place any heavy objects over the power cord.
•Position the power cord properly to avoid creating a trip hazard.
•Avoid electrical shock or fire, by not overloading the power cord.
•The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble this unit by
yourself. Consult an authorized technician instead.
•Make sure the power source that this unit is connected to has a continuous power flow.
•If there is need to use an extension cord, make sure said cord has a compatible power rating.
•Do not handle this or any other electrical device if you are wet or standing in water.
•Whenever the screen reaches its end of life, follow local environmental guidelines regarding its proper disposal.

Rev.02142023JA 2 www.epvscreens.com
Do not use this unit under the following circumstances.
•Disconnect the power cord if exposed to moisture, rain, wind, electrical storms or snow.
•Avoid exposure to direct sunlight or any of the conditions stated in the previous bullet point.
•Keep away from fire or other high temperature heat sources.
•Cut off the power supply first before attempting maintenance or removal.
•Do not attempt to use this screen if there are obvious signs of damage.
•To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious damage or
if there are any evident broken parts.
WARNING
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop in the
roller. Please be aware of this as it will void your warranty. Individual modifications to this product are prohibited and
will void the manufacturer’s warranty. Please contact the EPV Screens Customer Service Team with any questions.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. The product settings are designed to provide reasonable protection against any radio
interference within a residential installation, however the screen may suffer from Radio Frequency interference from
other home electronics.
Although radio interference affecting other household electronics is unlikely, the following steps can be taken should
RF interference occur.
✓Reorient or relocate the receiving antenna on the device that may be casing the interference.
✓Increase the distance between the screen and the interfering device’s receiver.
✓Connect the projection screen to another power source apart from the interfering device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen upright on a clean, level surface.
3. Keep the screen out of contact with foreign particles such as dust, sawdust, and/or liquids.
SHIPPING BRACKETS REMOVAL
WARNING!
PLEASE READ BEFORE INSTALLING!
Please note: Before fully operating the screen. Remove the
shipping brackets from the weight bar by loosening the 6 screws.

Rev.02142023JA 3 www.epvscreens.com
NOTE: Regardless of the mounting method, each screen should be securely installed so that vibrations or pulling on
the viewing surface will not cause the casing to become loose or fall. Included are complimentary mounting screws that
may or may not be appropriate for the installation you are attempting. Always use the correct anchors to safely secure
the screen and always consult a professional integrator.
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A. Wall/Ceiling
mount bracket
x2
B. M5x60
Screw x6
C. M12
Dry-wall
anchor x6
D. Bracket
connector x2
(Installed on
the housing)
E. M5x11 Bolt
Screw x4
(Attached to
Part D)
F. M5x25mm
round head
cross screws
x2
G. M5x30mm
eyebolt screw
& M5 nut x2
H.
Carabiner
x 2
Installation Instructions
For installation assistance, please consult a professional Installer. EPV Screens is not liable for faulty installations.
Two or more people are required while one holds the screen in place.
A. Wall Mount
Flush mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and
bottom screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked points and install the brackets with the dry-wall anchor(C), M5x60 screw (B),
Make sure both brackets are properly leveled.
3. Hang the screen by placing the lower “catch” located on the back over the brackets upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
B. Ceiling Mount
I. Ceiling Mount (movable position)
This mount method allows the screen to slide horizontally.
Front view of bracket (A)
M5x25MM round
head cross screws (F)
Wall
Front view of
bracket (A)
Side view of
bracket (A)
M5x25MM
round head
cross screws (F)
Ceiling
Side view of bracket (A)

Rev.02142023JA 4 www.epvscreens.com
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and
bottom screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked areas and install the brackets with the dry-wall anchor(C), M5x60 screw (B),
Make sure both brackets are properly leveled.
3. Hang the screen by placing the lower “catch” located on the back over the bracket’s upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
II. Suspended
1. Screw the eyebolt (G) onto the bracket connector (D).
2. Attach the snap link (H) through the eyebolt (G) and connect it to the ceiling eyebolt screw (not included) as
rated for the screen’s weight.
Screen material tension adjustment
(4mm Allen Wrench required and not included)
Remove the weight bar end cap to expose the adjustment
tension knob. This knob has a 4mm Allen port. Insert your
4mm Allen Wrench and push in the adjustment tension
knob, turn clockwise and your screen will gain more
tension. Turn the Allen Wrench counter clockwise and the
screen will lose tension. Please note this adjustment is not
necessary as the tension of the screen has been pre-set to its
factory drop setting. If you would like to adjust the screen
tension, please contact EPV Screens® for assistance to
avoid damaging the screen and voiding your warranty.
Power Max Tension ISF | Controls and Accessories
A. IR Remote
ZRC1-IR
B. RF Remote
ZRC1-RF
C. Wall box
controller
ZRC1-WB
D. RJ50 cable
ZRC1-RJ50
G. AAA
batteries
H. Bubble leveler
Screen operation
Electric Current: 110v
1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen has power, you will be able to control it using any of the 5 methods described below.
Ceiling
Push

Rev.02142023JA 5 www.epvscreens.com
5 Ways to control your PowerMax Tension screen
1. IR Remote control (Item A, Fig 1): The Infrared functions by direct line of
sight contact using an effective beam range of 25 feet within a 30-degree angle.
Aim the IR remote directly at either the IR receiver on the Wall Box Controller
or on the screen to operate the screen.
Note: Assure there is no obstruction between the IR remote and IR receiver.
2. RF Remote Control (Item B): The radio waves eliminate the need for a
direct line of sight and has a longer distance control range.
The RF remote is already pre-synced/paired and ready to use. If
synchronization/ pairing is needed, please follow the steps below.
How to synchronize/pair a new RF remote:
•Press & hold the “Programming Key”, then press the “Up Key” on the Wall box controller (wall-box
LED flashes). Reference the wall box controller section for programming key location.
•Then press the “Up Key” on the RF remote.
•The Wall box LED will flash 5 times, to indicate the RF remote has been properly synchronized/paired.
How to change the RF code (For use when multiple screens/RF remotes are owned)
Changing the RF code avoids controlling multiple screens at the same time and prevents electrical interference
leading to accidental control of the screen.
1. Remove the batteries
2. Change the RF code switch
3. Insert the batteries
4. Synchronize it with the wall box controller
3. Wall box controller (Item C, Fig 3): The wall box controller switch is a wall mounted control box with an
up/stop/down button. It plugs directly into the screen’s RJ50 port.
LED light
UP
STOP
DOWN
Fig.1
IR/RF remote
Wall box controller
IR Receiver
IR Lens
(IR remote only)
RJ50 cable
Wall box controller
SIDE VIEW
RJ50 PORT:
Connects to the
Screen RJ50 PORT
(RJ50 CABLE ONLY)
3.5mm mono Projector
Trigger Port (if Projector
equipped)
Wall box controller
BACK VIEW
Programming
Key
Battery compartment
Default
“000”
RF Remote
BACK VIEW
Slide Switches
for RF Code
change

Rev.02142023JA 6 www.epvscreens.com
4.Wired 5-12 volt trigger: Requires a 3.5mm to 3.5mm mono cable (not included)
Step 1: Connect one end the RJ50 cable to the screen and the other end
to the Wall box controller.
Step 2: Then connect one end the 3.5mm mono cable to the wall box
controller and the other to the projector.
Once the two cables have been connected, the wired trigger feature
is ready to synchronize the screen’s up/down operation with the
projector’s power cycle.
•Projector on, screen drops
•Projector off, screen raises
5. Wireless 5-12 volt trigger (Fig 5): Requires a 3.5mm to 3.5mm mono cable (not included).
The Radio Frequency (RF) remote control serves as a dual purpose, independently as a handheld remote control, or
as a Wireless 5-12 volt trigger. The radio frequency technology sends a wireless signal that synchronizes the
screen’s drop & rise with the projector’s power cycle.
Here’s how to set up your Wireless 5-12 volt trigger
The 5-12V wireless trigger should already be synced and ready to work.
Step1: Connect one end of the 3.5 mm mono trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm mono end of the cable to your projector
Step 3: Turn on the projector and the screen should automatically deploy.
Step 4: Turn off your projector and the screen should automatically retract.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-
30seconds for full off and on cycle each time)
Note: If the wireless trigger feature does not work, please resync the RF remote to the Wall box controller per the
instructions in the Radio Frequency remote section.
Mono 3.5mm
Projector Trigger
Port
Fig 5
3.5 mm port
DC 5-12V out
3.5mm to 3.5mm mono cable
UP
STOP
DOWN
Projector
RF remote control
SIDE VIEW
3.5 mm port
DC 5-12V out
3.5mm to 3.5mm mono cable
Wall box controller
Fig. 4
RJ50 cable
Projector

Rev.02142023JA 7 www.epvscreens.com
ADVANCED Programming Key Instructions: (FOR ADVANCED USERS ONLY)
Wall box controller must be connected to the screen.
1. Preset the Screen’s Drop Position:
Use the RF/IR remote or Wall Box Controller to Drop the screen to the desired position you want to set it at.
Press & hold the “Programming Key”, then press the “Down key”on the Wall Box Controller. The LED will flash 5
times to confirm new programmed drop position.
2. Clear/Reset the Screen’s Drop Position to factory default:
Press & hold the “Programming Key + “Stop key” on the wall box controller.
For more information, technical support or your local Elite Prime Vision
contact, please visit www.epvscreens.com
PROGAMMING NOTE:
The programmed vertical drop position will have +/- 2" tolerance, which will depend on the temperature of the
installed screen environment.
ATTENTION: Reducing the factory’s full screen drop may produce waves/wrinkles on the projection surface on
tab-tension screens. The full drop is recommended to allow the screen to rely on the tab-tension system to
maintain the projection surface flat and taut on all sides.
The same applies on non-tensioned screens, although some level of waves may be present due to the nature of
the screen not being tensioned. If wrinkles/waves develop after making the adjustment to the desired drop
position, reset it to the factory’s default position per the instructions below.