EPV Prime Vision ISF Series User manual

JA-022818 www.EPVscreens.com 1
Matte White Fixed Frame Projection Screen
Prime Vision ISF Series
User’s Guide
Thank you for choosing the Prime Vision ISF fixed frame projection screen! The Prime Vision ISF Series by
EPV Screens® leads the industry in quality fixed frame projection screens. Its design features a 2.4” wide
frame with velvet coating that frames its ISF Certified ChromaWhite screen material. The ChromaWhite is
specially formulated to provide diffusion uniformity with accurate color reproduction for a flat spectral
response in a controlled room environment.
Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure a
long product life.
Care & Use Instructions: Dust, dirt and scratches on the projection surface will affect the picture
quality, please take note of the points below to prevent that from occurring:
1. Do not touch the projection surface with your hands
2. Do not write or draw on the projection surface
3. Do not use fingers or sharp objects to point on the projection surface.
4. Use clean water when dampening the cleaning cloth and do not rub against the material.
5. Do not use chemical cleaning agents or alcohol to clean the screen material.
Note: Please make sure all parts are included in your package before assembling your Prime Vision ISF
fixed frame projection screen.
Hardware and Parts List
A. Frame Parts x 6 pcs
(4 top/bottom frame pcs + 2 side frame pcs)
H. M5x15 screw x 16 pcs
B. ChromaWhite Screen Material x 1 pc
I. Center Support Bar x 1 - 2 pcs
(depending on model/size)
C. Center joint x 2 pcs
J. Support joiner x 2 - 4 pcs (depending on model/size)
(Install into the support bar before shipment)
D. Elbow Joint x4 pcs
K. Fix Plates x 60 - 180 pcs
(depending on model/size)
E. Wall bracket x 4 pcs
L. Rubber mallet x 1 pc
F. Wood screw x 8 pcs
M. Screw driver x 1 pc
G. Hollow wall anchor x 8 pcs

JA-022818 www.EPVscreens.com 2
FRAME ASSEMBLY
1. Insert the center joint (c) connector to the horizontal frame piece with bevel connection and flat head, and
then fasten it with two M5x15 screws (h).
2. Insert the other horizontal frame piece to the center joint connector and then fasten it with two M5x15
screws.
Note: a. 2 long frames should be assembled for a screen.
b. Do not tighten the screws completely until all frame pieces have been assembled correctly.
3. Insert both elbow joint connectors into the long horizontal frame and then fasten it with two M5x15
screws (see Fig.1). Then insert the short frames and fasten them with screws (Fig.1.2).
Push Push
Joint
Long frame
( fig.1)
Flat head
bevel connection
Bevel connection
Flat head
×2
½ Long Frame
½ Long Frame
Push
Horizontal Long Frame
M5x15 Screw
M5x15 screws
M5x15 screws

JA-022818 www.EPVscreens.com 3
Push Push
( fig.2)
Insert the exposed ends of the joint connectors
into the short (vertical) frame and align the four
corners so that they meet at perfect right angles
4. Join all four frame parts together following the steps shown below. (Fig.2)
Note: When assembled, please push simultaneously the two ends of the long frames.
Push Push
Short frame
Short frame
M5x15 screws
Screw
( fig.3)
M5×15Screws
Screw
( fig.3)
(Fig.1.1)
(Fig.1.2)

JA-022818 www.EPVscreens.com 4
Attaching the Screen Material to the Frame
1. Make sure the screen material and frame are both lying face down on a clean, dry, and non-abrasive
surface.
2. Carefully unroll the material inside the frame. (Fig.3)
Please note the material will be noticeably smaller than the frame, as the material must be stretched to create a
sufficient amount of tension for perfect material flatness.
3. Attach the fix plates.
(1) Stretch the material to the corner and insert the screen material’s edge in the groove of the frame.
While one hand holds the material in place the other hand snaps in the push plate (Fig.4-Fig.5).
(2) Begin by securing the four corners in the following sequence: A→B→C→D (Fig.6).
(3) Insert the fix the plates as shown on Fig. 5. Fix plate ① is about 10cm away from the frame’s corner.
Fix plate ② is about 5cm away. (Fig.7)
(Fig. 6)
(Fig. 7)
Notes：
•Make note of the label to help distinguish
the back and front side.
•Unroll the screen material face down
•Keep the screen material as close as
possible to the frame and do not allow it to
scratch against any part of the frame.
(Fig. 4)
Insert push plate in
Screen material edge
(Fig. 5)
Schematic cross section of the frame
Plate
Frame groove
A
B
C
D
(Fig.3)

JA-022818 www.EPVscreens.com 5
(4) Place a fix plate in the center of each side in the following order E→F→G→H.(Fig.9)
(5) Next, fasten a fix plate on the center of each frame side in the following order
I→J→K→L→M→N→O→P as shown in Fig.10.
(6) Fasten the remainder of the fix plates in the empty locations in the red markings to complete attaching the
screen material. (Fig.11)
E
G
H
F
(Fig.9)
(Fig.11)
I
J
K
L
M
N
O
P
Tip for attaching the last corner (D):
1. Position yourself left of location ①.
2. Pull the material to the corner of the frame with your hand while your left
hand snaps in the fix plate on location ① (the third red dot).
3. Then insert and snap in the fix plate on location ②.
4. Next, move and position yourself on location ③，then pull the edge to the
frame and fasten plates on locations ③ and ④.
5. Finally, fasten the last fix plate on location ⑤. (Fig.8)
(Fig.10)
①
②
③
⑤
④
Pull
(Fig. 8)

JA-022818 www.EPVscreens.com 6
Center Support Bar Installation
1. Insert the Center Support Bar into the upper top groove on the back of the frame (not the one where
the fix plate inserts) with the bottom end near the approximate center point of the frame and rotate it in at an
angle so that both ends of the bar are in alignment with the groove (see Fig. 17 below for details).
Diagonal models bleow 165” use 1 x Center Support Bar
Diagonal models 165” and above require 2x Center Support Bars
2. Slide the top end of the bar into the top center point of the frame to complete the center support bar
installation. This will provide added stability to your frame and added tension to the material.
Screen material edge
Center Support Bar
(Fig. 17)
Remove
push
Center Support Bar
Fixed plate groove
(Do not insert here)

JA-022818 www.EPVscreens.com 7
Installation
1. Locate your desired installation location with a stud finder (recommended) and mark the drill-hole
area of where the screen is to be installed.
2. Drill a hole with the proper bit size according to the wood screws included.
3. Line up the wall brackets with the drilled holes on the installation location and screw them in using a
Phillips screwdriver.
Note: Use 2 top wall brackets on diagonal sizes below 135”, and use 3 top wall brackets on
diagonal sizes 135” and above.
4. Position the fixed frame screen onto the top wall brackets as shown in Fig. 18 and push down at the
center of the bottom frame to secure the installation.
5. The design of the wall brackets allows the frame to slide over them through its sides. This is an
important feature of the installation design as it allows your screen to be properly centered.
6. Using both hands finish the installation by pushing the lower portion of the fixed frame screen into
the lower bracket as shown in Fig. 19.
CAUTION
Please follow these instructions carefully to ensure proper maintenance and safety of your Screen.
1. When hanging the screen up, please make sure that no other objects such as power switches, outlets,
furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame screen.
2. Regardless if the screen is hung on or installed into the wall, make sure that the proper mounting anchors
are used and that the weight is supported appropriately by a strong and structurally sound surface just as any
large and heavy picture frame should.
3. Frame parts are made of high quality velour-surfaced aluminum and should be handled with care.
4. When not in use, cover over the screen with a furniture sheet to protect it from dirt, grime, paint or any
other impurities.
5. When cleaning, use a damp soft cloth with warm water to remove any marks on the frame or screen
surface.
6. Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.
7. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or any other sharp
or abrasive objects.
8. Spare Parts should be placed out of reach of small children in accordance with household safety guidelines.
For a local Elite Prime Vision® contact or Technical Support, please visit
www.EPVscreens.com
(Fig. 18)
(Fig.19)