Elite Screens aeonclr series User manual

Rev.071816-DR www.elitescreens.com 1
AeonCLR™ Series
EDGE FREE® Fixed Frame Screen w/ StarBrightCLR®
(Ceiling Light Rejecting) Front Projection Material
User’s Guide
Product Description:
The Aeon CLR™ Series is an ultra-short throw fixed frame projection screen that uses Elite’s EDGE FREE®
technology. It is designed for with Ultra-Short Throw Projectors only, for use in environments where ceiling light
cannot be entirely controlled. It includes an LED backlight kit and a bezel trim to further enhance the frame appearance.
Screen Maintenance
Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the projection image.
For optimal results we advise to pay attention to the following instructions.
1) The screen surface has a horizontal structure. DO NOT wipe the screen up and down or in a circular motion.
Wipe from left to right only.
2)Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth may damage the
screen’s surface).
3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.
Notes：
The following precautions should be followed at all times to avoid damaging the material, which is not
covered under warranty.
 Don’t touch the screen material to avoid leaving fingerprints. Use gloves when handling the material.
 Don’t scratch the material,as it will leave permanent markings on the screen’s surface.
 Don’t point to the screen material with a fingertip or other sharp objectsto prevent damage to the material.
 Don’t use acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using such
chemicals will permanently damage the screen.
Assembly Video
Watch our assembly video on-line at
www.elitescreens.com/aeonCLR_assembly
or scan the QR code

Rev.071816-DR www.elitescreens.com 2
Hardware and Parts List
Please make sure all parts listed below are included before installation.
A. Elbow joint x 4 pcs B. Top/Bottom horizontal frame x
4 pcs
C. Left/Right vertical frame x 2 pcs D. Center joints x 2 pcs
E. Center support bar x 1-2 pcs F. Wall brackets x 2-3 pcs G. M6 screw x 2-4 pcs H. M5x15 screw x 24 pcs
I. M6x12 screw x 2-4pcs J. Screw and anchor x 6-9 pcs K. Rubber mallet x 1 pc L. Screw driver x 1 pc
M. Black Tape x 1 bag N. Bezel trim x 6 pcs O. Corner sleeve x 4 pcs P. White gloves x 2 pcs
Frame Assembly
1. Insert the center joint into one of the ½ horizontal frames and fasten it with the two M5x15 screws (H).
2. Insert the other ½ horizontal frame piece to the center joint and fasten also using two M5x15 screws.
3. Repeat steps 1 and 2 for assembling the second horizontal frame.
Push Push
4. Insert and slide in oneM6 screws(G) through the channel located on the backof each horizontal frame (B).
Place one M6 hex screw (G) in the center for attaching the center support bar (E)
Horizontal frame
Top right Frame Top left Frame
Horizontal long frame
Face up
M6 hex screws (G)
Center joints

Rev.071816-DR www.elitescreens.com 3
5. Insert the elbow joint (A) into each end of the horizontal frames (B) as shown below.
6. Insert the two vertical short frames(C) into the elbow joint (A).
7. Join the remaining horizontal long frame (B) with the frame built in the previous steps as shown below.
Horizontal Long frame (B)
Horizontal long frame (B)
ElbowJoint
(A)
Push
Push
Elbow Joint
(A)
Horizontal long frame (B)
Vertical short frame(C)
push push
Push

Rev.071816-DR www.elitescreens.com 4
8. Make sure all four corners are properly in place to form a perfect square.
Then fasten the four angles with the M5x15 Screws (H).
Screen Material Installation
Please read this important note before proceeding with the installation process of the material:
Before handling the StarBright CLR® material, put on the supplied pair of white gloves to avoid leaving
fingerprint marks, dust or hand oil on the material’s surface (Figure1). The StarBright CLR® material is very
delicate and should be handled with extreme care. Do not allow the material to fold or bend. Failure to follow
instructions will result in permanent damage to the screen material, which is not covered by warranty.
1. Remove the StarBright CLR® material from the packaging tube and set it gently on a clean surface.
Tip: Carefully put a small flat weighted object at the edge (PVC/Velcro end) to prevent it from moving out of place.
Please keep the front of the materialface down.
2. It is strongly recommended for two people to unroll the material to prevent the screen from bending or rolling
unevenly. Each person holds one end of the roll and slowly unrolls the screen in a clockwise direction (Figure 2).
3. Lay the material completely flat with the front facing down on a clean surface in a horizontal position (Figure 3).
Four corners join correctly to form a perfect
rectangle. Use the included screwdriver (L)
to fasten the Mx15 screws (H) into each
corner by aligning the frame screw holes to
the holes in the elbow joint (A).
Figure 2
Back side of material
Front side of material
Horizontal positionlaid ona clean surface
Figure 3
Figure 1
Tip: Small weighted object

Rev.071816-DR
www.elitescreens.com
4. Carefully and gently
place the assembled frame
allow the angle edge of the frame to come in direct contact with the material to avoid puncturing
5.
After all of the corners of the frame have been
following order A→B→C→D
(see instructions below for details)
Attach the screen material to the corners as shown below.
2) Fold over and
material to the Velcro
strip of the frame.
1) Stretch the screen material in
the directionof the arrowhead.
B
C
www.elitescreens.com
place the assembled frame
on top of the screen material
as shown below
allow the angle edge of the frame to come in direct contact with the material to avoid puncturing
After all of the corners of the frame have been
properly aligned (example A), attach
the material on the frame in the
(see instructions below for details)
.
Attach the screen material to the corners as shown below.
Screen material back facing up
2) Fold over and
attach
material to the Velcro
strip of the frame.
3) Fold over second side
and attach to frame
4)
Repeat until all four sides
are done in the order A, B, C, D
A
D
5
as shown below
. Make sure to not
allow the angle edge of the frame to come in direct contact with the material to avoid puncturing
or damaging it.
the material on the frame in the
Screen material back facing up
Velcro
Repeat until all four sides
are done in the order A, B, C, D
A

Rev.071816-DR www.elitescreens.com 6
6. After all four corners have been attached; please check whether the screen material wraps the frame corners. If not,
please loosen the Velcro connection and repeat the above steps so the frame is not exposed.
7. Proceed to attach the rest of the material to the frame as described in the illustrations below.
Note:
Represents
thescreen
Lay the Velcro end on the screen material over the
Velcro end of the frame and keep it within the
edge.
Proceed in the following sequence ①②
Attach in the following
sequence:a-b-c-d
Note: The black shaded part
represents the Velcro on the
frame. That Velcro end will
ultimately attach with the
other Velcro end on the
screen material.
D
The key is to attach within the middle sections
of 1 and 2. Then continue attaching the
remaining unattached areas.
Repeat the same steps on remaining
three sides in the sequence A, B, C, D.
Grasp the middle of the screen
material and attach it to the Velcro
strip on the frame
A
B
C

Rev.071816-DR www.elitescreens.com 7
Screen Material Removal
Follow the steps to properly remove the screen material from the frame. This procedure will ensure prolonging the life
of the screen material.
1. Detach the Velcro from the frame.
2. Gently pull back the material to release the material from the Velcro connections on the corners
Support bar installation:
1. Position the center support bar (E) in the middle of the frame and align the hole on each end of the support bar with
the M6 hex screws (G) on the top and bottom frames.Then fasten with the M6x12 screws (I).
Pull back the screen material from
the Velcro connection along the
edges of the frame to detach it.
Support bar
Move the M6 hex screw (D) to the middle area of the frames.
Align the M6 screws
with the two holes.

Rev.071816-DR www.elitescreens.com 8
Edge trim Installation
Included is an black edge trim that provides an elegant ultra-thin bezel finish
1. Place the assembled frame on a flat and clean surface. The projection screen surface should be facing up. Align
the tape with the edge of the screen, as shown in Figure 1. Once properly aligned, apply the black tape to the
center of the top and bottom of the screen material.
Figure 1
2．Without removing the adhesive tape, place all the trim pieces along the edge of screen material. Adjust the trim
pieces so that the four corners are evenly aligned. (Note: The Elite logo should be positioned on the bottom right).
Refer to Figure 2 below for a visual reference.
Figure 2
NOTE: Make sure the bottom edge trim with the Elite Screens logo is installed on the correct side. The back of the
material should be labeled with a DOWN sticker to indicate the material is facing in the down position. The Elite
Screens logo should be installed on the DOWN side
Plastic corner sleeve x4pcs
Edge trim x 6 PCS
Black tape x1pcs
Trim
strip
Screen Material
The black tape
The black tape
Front Side
Back Side

Rev.071816-DR
www.elitescreens.com
3.
After properly aligning all trim pieces, carefully remove trim piece
backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining
trim pieces in the following order: B
Figure 3
4. After the bezel trim has bee
n installed
the corner sleeve
through the front of the screen
bezel trim.
Once all corner sleeves have been snapped into each corner of the frame, it is ready to be
Diagonal Size Note
The Diagonal Size of the AR100H-CLR
before and after installing the
Before installing the trim strip
A
B
F
D
E
www.elitescreens.com
After properly aligning all trim pieces, carefully remove trim piece
A
(see Figure 3 below). Remove the inside
backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining
trim pieces in the following order: B
-C-D-E-F.
Figure 3
The front side
of the frame with trim pieces attached
n installed
, placea corner sleeve (O)on all four corners.
Begin by
through the front of the screen
. Make sure the corner sleeve
completely
Once all corner sleeves have been snapped into each corner of the frame, it is ready to be
wall installation
before and after installing the
edge trim strip.
Before installing the trim strip
After installing the trim
Front side
C
9
(see Figure 3 below). Remove the inside
backing of the tape and place the trim piece in its original position on the frame. Repeat this step for the remaining
of the frame with trim pieces attached
Begin by
aligning and adjusting
completely
wraps the edge of the
wall installation
.
After installing the trim
strip
Back side

Rev.071816-DR www.elitescreens.com 10
Proper Projector Placement for StarBright CLR®
The StarBright CLR® is exclusively for table-mounted ultra-short throw projectors as illustrated in example
1 below. Overhead placement or a standard projector will make the image very dark, on account of the screen’s
absorbent layer deflecting light that is not aligned with its reflective angle.
Example 1: Proper Projector Installation
Example 2: Improper Projector Installation