EPV Prime Vision ISF Series User manual

05232022JA www.epvscreens.com U-00221 1
Prime Vision ISF Series
Matte White Fixed Frame Screen
USER’S GUIDE – M Type
V 2.0
Thank you for choosing the Prime Vision ISF fixed frame projection screen! The Prime Vision ISF Series
by EPV Screens® leads the industry in quality fixed frame projection screens. Its design features a
lightweight aluminum frame with velvet coating that frames its ISF Certified ChromaWhite screen
material. The ChromaWhite is specially formulated to provide diffusion uniformity with accurate color
reproduction for a flat spectral response in a controlled room environment.
Please read through this user guide before utilizing the screen. Correct usage and maintenance will ensure
a long product life.
In order for the ChromaWhite to maintain its projection qualities and optimum performance please refer to the list
below for proper maintenance and cleaning.
Care & Use Instructions: Dust, dirt and scratches on the projection surface will affect the picture quality,
please take note of the points below to prevent that from occurring:
•Use a dry microfiber cloth to remove dust from the screen’s surface.
•Do not write or draw on the projection surface
•When cleaning, use a damp microfiber cloth with warm water to remove anymarks.
•Never rub or apply pressure when cleaning the surface.
•Never attempt to use any solutions, chemicals, or abrasive cleaners on the screen surface.
•To avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other
sharp or abrasive objects.

05232022JA www.epvscreens.com U-00221 2
Frame Parts List
A. Vertical Frame x 2pcs
B. ½ Horizontal Frame x2 pcs
C. ½ Horizontal Frame x 2 pcs
Hardware Parts List
a. M4*4
b. D5*4
c. M4*4
d. D5*4
g.
h.
i.
j.
k.
l.
o.
p.
r.
Item
Parts List
110”
120”
135”
150”
138”
158”
16:9
2.35:1
a.
Center Joints- M4 (bottom position)
2
2
2
2
2
2
b.
Center Joints-D5 (top position)
2
2
2
2
2
2
c.
Elbow Joints M4 (bottom position)
4
4
4
4
4
4
d.
Elbow Joints D5 (top position)
4
4
4
4
4
4
g.
M4x7 Screws
24
24
24
24
24
24
h.
Spring
66
72
80
88
80
92
i.
Pull Hook
2
2
2
2
2
2
j.
Wall brackets
4
4
4
4
4
6
k.
Wall Screws M5x50
8
8
8
8
8
12
l.
Hollow Wall anchors
8
8
8
8
8
12
o.
Center Support Bar
1
1
1
1
1
2
p.
White gloves
2
2
2
2
2
2
r.
Φ3 mm Long Iron (sides) rod /
Short rod (top/bottom)
2/4
2/4
2/4
2/4
2/4
2/4
C+B
B+C
A
A
Red
Black

05232022JA www.epvscreens.com U-00221 3
Frame Assembly
Step 1: Place the EPE sponge (foam) sheet on the ground of the area where the screen will be assembled.
Step 2: Position the pieces of the frame on the EPE sponge in the arrangement shown below.
Step 3: Insert center joint (a/b) connectors into one-half of the horizontal frame (B/C) and secure with the M4x7
screws (g) as shown in the illustration below.
Step 4: Connect the elbow joints (c/d) to the top and bottom sections of the vertical frame. Once inserted, connect
the vertical sections to the horizontal frame sections. Make sure all holes are in alignment and the frame pieces are
flush (no gaps). They should form perfect right angles.
8.
a.
b.
d.
c.
Tip: The center joint (b) with the larger diameter holes should be on top.
Tip: The elbow joint (d)with the larger diameter holes should be on top.

05232022JA www.epvscreens.com U-00221 4
Step 5. Secure the elbow joints by fastening them with M4x7 screws (g), 4 at each corner.
Screen Material
Step 6: Put on the white gloves (p) and carefully unroll the screen material on a clean surface from the roller to
the other side as shown below. The back side of the screen material should be placed upwards.
Step7: Carefully place the screen on top of the assembled frame as shown below.Make sure that the angular edges
of the frame are not allowed to come into direct contact with the screen material to avoid puncturing.
Front

05232022JA www.epvscreens.com U-00221 5
Step 8: Insert the rods (r) through the sleeves according to their corresponding lengths on each edge of the screen
as shown below. The short rods (top/bottom) will overlap to secure a firm grasp in the middle areas.
How to attach the springs
Step 9: Hook one end of the spring and secure inside the groove of the frame, use the spring hook (i)to attach the
spring to the hole located on the screen material’s outer edge in the following order.
Back Side
Back Side
Back Side
c
r. (Red tips)
r. (Black tips)
Back
Side
Go through the hole
from bottom to top
h.
i.
Spring must hook both
overlapping
short rods.
c
c

05232022JA www.epvscreens.com U-00221 6
First connect on four corners, steps 1-4. make sure all four corners are fixed before proceeding with next spring.
Continue to attach the remaining springs to the material in steps 5-12 in the follow order.
1
2
4
3
5
6
7
8
9
10
11
12

05232022JA www.epvscreens.com U-00221 7
Step 10: Insert the Center Support Bar (o) into the upper top groove on the back of the frame with the bottom end
near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment
with the groove.
Installation
Step 11: Measure the overall length and height of the frame and drill holes for the top brackets. Line up the wall
brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. If not
installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws with a
screwdriver. Make sure the brackets are leveled.
Diagonal Sizes of 150” and below use 4 x wall brackets
Diagonal Models 150” and below use 1 x
Center Support Bar
Diagonal Models above 150” require 2 x
Center Support Bars
Model/Size
X = Wall bracket distance
X1 = Bracket hole distance
Y = Top/Bottom Wall Bracket Height
110”
1280mm (50.39”)
30mm (1.18”)
1410mm (55.51”)
120”
1390mm (54.72”)
30mm (1.18”)
1530mm (60.24”)
135”
1550mm (61.02”)
30mm (1.18”)
1720mm (67.72”)
150”
1720mm (67.72”)
30mm (1.18”)
1900mm (74.80”)
138”
1600mm (63”)
30mm (1.18”)
1410mm (55.51”)
Don’t tighten the screw to allow
the screen to move up and down
j.
k.
Place a center
support bar 30 cm
(11.8”) apart from
the center (red line).

05232022JA www.epvscreens.com U-00221 8
Diagonal Models above 150” require 6 x wall brackets
Step 12: Position the fixed frame screen onto the top wall brackets (fig 1) as shown below and push down at the
center of the top of the frame (fig 2) to secure.
For Technical Support or an EPV Screens contact in your area,
visit www.epvscreens.com
Model/Size
X = Wall bracket distance
X1 = Bracket hole distance
Y = Top/Bottom Wall Bracket Height
158”
900mm (35.43”)
30mm (1.18”)
1610mm (63.39”)
c
c
1.
2.
Don’t tighten the screw to
allow the screen to move
up and down