Ergotron SV Combo User manual

1 of 6
888-97-398-G-00 rev. B • 08/19
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
SV Combo 9" Extension
User's Guide
English
For the latest User Installation Guide please visit: www.ergotron.com
*Product shipped with rotation stop in place to prevent the Extender from hitting the wall.

2 of 6
888-97-398-G-00 rev. B • 08/19
17 mm
AB CD
1
2
3
180˚*
360˚
360˚
4x
3 mm
6 mm
1x
1x
1x
1x 1x
1x
1x
1x
1x
1x
1x
13mm
Components
Tools Needed
Set-up
Features & Specifi cations

3 of 6
888-97-398-G-00 rev. B • 08/19
1
5.63”
(143 mm)
6.93”
(176 mm)
1.38”
(35 mm) Ø 0.43”
(11 mm)
2.64”
(67 mm)
Back View
5’3”-5’9”
(160-175cm)
21”
(533 mm)
31.5”
(800mm)
< 30.5”
(775mm)
Combo Arm Without Worksurface
Combo Arm Extender
6”
(152 mm)
24”
(610mm)
7.8”
(200mm)
7.7”
(196mm)
29”
(737mm)
19.6”
(498mm)
20.6”
(524mm)
30”
(759mm)
21”
(533mm)
28.5”
(723mm)
2.56”
(65mm)
10” (252mm)
NOTE: Fasteners may unwind due to vibration caused by movement of mounting solution over time. Inspect mounting
solution for loose fasteners on a routine basis. If desired, apply a light duty thread locking adhesive to fasteners before
installation to prevent back-out.
Mounting Height for Ergonomic Workstation
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5’3”-5’9” (160-
175cm).
If user heights are dierent than this, you should change mounting height to accommodate user heights. (Change mounting
height one inch for every one inch dierence in user heights).
Mounting height assumes there is a 6” (152 mm) distance between the
center of your monitor mounting holes and the top of the screen. If your
distance is smaller, you should increase mounting height accordingly, if
your distance is larger, you should decrease your mounting height ac-
cordingly.
Determine mounting location:
Front view with arm pushed back against the wall.
Top view showing range of motion when pulled out
from the wall.

4 of 6
888-97-398-G-00 rev. B • 08/19
2
3
4
1x
1x
3 mm
17 mm
1/4"
(6.4mm)
IMPORTANT! Torque bolts in the sequence shown above to a minimum of 50 lb-ft (6.91 kgf-m).

5 of 6
888-97-398-G-00 rev. B • 08/19
5
6
13 mm
4x

6 of 6
888-97-398-G-00 rev. B • 08/19
© 2015 Ergotron, Inc. All rights reserved.
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
NOTE: When contacting customer service, reference the serial number.
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics