Ericsson RBS 6402 User manual

Install RBS
RBS 6402
INSTALLATION
56/1531-LZA 701 6001 Uen D

Copyright
© Ericsson AB 2015. All rights reserved. No part of this document may be
reproduced in any form without the written permission of the copyright owner.
Disclaimer
The contents of this document are subject to revision without notice due to
continued progress in methodology, design and manufacturing. Ericsson shall
have no liability for any error or damage of any kind resulting from the use
of this document.
Trademark List
All trademarks mentioned herein are the property of their respective owners.
These are shown in the document Trademark Information.
56/1531-LZA 701 6001 Uen D | 2015-11-06

Contents
Contents
1 Prerequisites 1
1.1 Documentation 1
1.2 Tools and Equipment 1
2 Install RBS 5
3 Appendix A: Ceiling Installation and Working at Heights 15
4 Appendix B: Install Fan Unit 19
5 Appendix C: Install External Antenna 21
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
56/1531-LZA 701 6001 Uen D | 2015-11-06

Prerequisites
1 Prerequisites
This section contains information on the documents, tools, and equipment
required for installing RBS 6402.
1.1 Documentation
Read the following documents:
•Personal Health and Safety Information
•System Safety Information
•Transportation and Storage
•Integrating RBSs On-Site Using ENIS
•Handling SFP Modules and Optical Cables
•SFP Module Selector Guide
1.2 Tools and Equipment
The following tools and equipment are required:
Required Equipment
Contents:
- RBS
- Drilling template
- Mounting bracket
RBS package AndroidTM phone with Ericsson
Node Integration Scanner (ENIS)
application
Spirit level
1
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Required Equipment
< 6 mm
(1/4″)
< 6 mm
(1/4″)
< 13 mm
(1/2″)
Hammer drill Hammer drill bit for plugs suitable
for ≤6 mm screws
3 screws with plugs
and screwdriver
Screwdriver TORX®T20 Data cable, optical or Ethernet Cable tie tensioner and
cable ties
Optional Equipment
Power cable Small Form-Factor Pluggable
(SFP) module
Global Positioning
System (GPS) cable
Ferrule end-face cleaner — for
optical cables
Safety Equipment
256/1531-LZA 701 6001 Uen D | 2015-11-06

Prerequisites
Hearing protection Eye protection
Optional Safety Equipment
Helmet and harness — when
working at heights
ESD Protective Gloves — for
external antenna installation
3
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
456/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
2 Install RBS
Note
Ge7445A
Always rest the RBS on a flat, nonabrasive surface.
r > 40 mm
The minimum bending radius for optical cables is 40 mm.
Danger!
Never look directly into the end of a fiber optic cable or other laser source.
Equipment that transmits laser light can cause permanent eye damage. Switch
off the laser before starting work on laser equipment.
1. Unpack
5
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Check that the delivered items correspond to the packaging list.
Examine the box and the RBS for damage. For more information,
refer to Handling Faulty Equipment.
2. Scan Barcode
Ge7235A
Work Order
(1P)INX1051532/4
(21P)P18 (120)20140923
(22P)RBS6402
MadeinSweden
(S)CB28350360
(1P)INX1051532/4
(21P)P18 (120)20140923
(22P)RBS6402
MadeinSweden
(S)CB28350360
To prepare the RBS for autointegration, scan the barcode on the
back of the RBS and the QR-code on the work order, using the ENIS
Android application. Use ENIS to send the retrieved serial number
and node logical name to the Operations Support System for Radio
and Core (OSS-RC). For more information, refer to Integrating RBSs
On-Site Using ENIS.
Ge7795A
(1P)INX1051532/4
(21P)P18 (120)20140923
(22P)RBS6402
MadeinSweden
(S)CB28350360
The barcode is also visible on the bottom of the RBS.
3. Install SFP Module
656/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Ge7104A
If applicable, insert the SFP module in the port marked WAN B.
For more information about handling SFP modules, refer to Handling
SFP Modules and Optical Cables and SFP Module Selector Guide.
4. Install Mounting Bracket and Prepare Cables
Protect the RBS and cables from dust by keeping them in the box
when drilling.
Ge7009A
DRILLING TEMPLATE / QUICK GUIDE
Put the drilling template on the wall and ensure that it is straight by
using a spirit level. Make sure that the entire drilling template fits on
the wall without it folding around any corners. Use the double-sided
tape at the corners of the template to attach it to the wall.
Ge7010A
If applicable, drill the three holes marked on the drilling template.
Ge7011A
Attach the two upper screws in positions to hang the mounting
bracket.
7
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Ge7012A
Hang the mounting bracket on the two upper screws.
Ge7013A
1
3
2
Attach the third screw and tighten all the screws using a screwdriver.
Ge7446A
Prepare the cables so that they are at the correct length (as indicated
on the drilling template).
Ge7447A
Route all cables through the cable holders on the left-hand side of
the RBS. Secure the cables with cable ties as indicated in the figure.
Note
856/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Ge7234B
The RBS can be installed horizontally on ceilings, see Appendix A
for more information.
The RBS can optionally be installed with the external antenna
adapter, see Appendix C for more information.
5. Attach RBS to Bracket and Connect Cables
Ge7014B
Hang the RBS on the mounting bracket hooks.
Ge7448A
click
click
Press down gently so that the RBS locks onto the hooks.
Ge7015A
Connect the cables.
Note that there are two options for powering the RBS and they
determine the order of the cabling, as follows:
• Power over Ethernet (PoE), with a PoE Ethernet Switch or a PoE
Injector to the RJ-45 connector
• AC/DC power converter (48 V DC to the DC input connector)
9
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Ge7102A
WAN A / PoE WAN B48 V
When using PoE with a PoE Ethernet Switch or a PoE Injector to the
RJ-45 connector, connect the cables in the following order:
Connect the external antenna cables on the back
of the RBS; see step 11 and step 12 in Appendix
C for more information.
Connect the GPS Receiver Unit (GRU) cable to
the GRU port with the Mini I/O connector. The
RBS uses an external GRU module.
Connect the optical cable to the WAN B port.
Connect the RJ-45 cable to the WAN A / PoE
port. Only connect the RJ-45 cable when all other
cables have been connected.
When using an AC/DC power converter, connect the cables in the
following order:
Connect the RJ-45 cable.
10 56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Connect the external antenna cables on the back
of the RBS; see step 7 in Appendix C for more
information.
Connect the GRU cable to the GRU port with the
Mini I/O connector.
Connect the optical cable to the WAN B port.
Connect the DC power cable of the AC/DC
converter to the DC input connector. Only
connect the power cable when all other cables
have been connected.
Note
Always clean optical cable connectors before connecting them.
For more information about handling optical cables, refer to Handling
SFP Modules and Optical Cables and SFP Module Selector Guide.
Ge7016A
click
click
Check that there are no kinks in the cables and that they are placed
securely in the cable holder. Attach the RBS to the bracket by gently
pushing the bottom of the RBS against the bracket until it clicks.
11
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Ge7017A
1.5 Nm
T20 Torx Fasten the RBS to the mounting bracket, by tightening the screws
to 1.5 Nm.
Ge7449A
Check that the RBS is securely attached.
6. Verify
Ge7024C
15 sec
Confirm that the green operational indicator is on and that no alarms
are active. A flashing green operational indicator means that the
integration is in progress. It takes about 15 seconds after the cables
have been connected before the operational indicator starts to flash.
If there is an error, redo the autointegration process in step 2. If the
error prevails, refer to Handle Faults On-Site.
7. Clean Up
Ge7018A
Remove the drilling template.
12 56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Dispose of waste according to local regulations.
13
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
14 56/1531-LZA 701 6001 Uen D | 2015-11-06

Appendix A: Ceiling Installation and Working at Heights
3 Appendix A: Ceiling Installation and
Working at Heights
Ge7234B
Use appropriate safety equipment, such as helmet and harness.
Use eye protection.
Optical cables are fragile so lift with care. Do not attach a pulling wire
directly to the optical cable, rather attach the pulling wire to a loop
and use the loop to lift the cable.
15
56/1531-LZA 701 6001 Uen D | 2015-11-06

Install RBS
Note
Before installing the RBS on a ceiling, the fan unit must first be
installed on the RBS. See Appendix B for more information.
DRILLING TEMPLATE / QUICK GUIDE
Ge7233B
1. Put the drilling template on the ceiling and ensure that it is straight.
Make sure that the entire drilling template fits on the ceiling without it
folding around any corners.
Ge7119A
2. If applicable, drill the three holes marked on the drilling template.
Ge7105
3. Attach the two upper screws in positions to hang the mounting
bracket.
Ge7106
4. Hang the mounting bracket on the two screws.
16 56/1531-LZA 701 6001 Uen D | 2015-11-06