ESCALADE Prince T8830 User manual

MODEL NO.
T8830
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
A S S E M B L Y I N S T R U C T I O N S
Contact Escalade® Sports customer service department at:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [email protected]
Please Do Not Return This
Product to the Store!
2015 Escalade Sports
2L-4238-01
“ S P O R T ”
T A B L E T E N N I S T A B L E

Prince (tm) is a trademark of Prince Sports, LLC.
© 2015 Prince Sports, LLC.
www.princetennis.com
P R E - A S S E M B L Y T I P S
Contact Escalade® Sports customer service department at:
Phone: Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please Do Not Return This Product To The Store!
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
1-866-873-3528
2015 Escalade Sports
2L-4238-01
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for
kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Tools required for assembly: Phillips Screwdriver, one 3/8” Wrenches, Two 7/16” Wrenches (Ratchet and 3/8”, 7/16” Sockets are
recommended and can be substituted for wrenches), Rubber Mallet or Hammer.
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could over-tighten the
and strip the screws out of the wooden table top.
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
P R E - A S S E M B L Y T I P S

(Qty. 6)
1/4-20 Locknut
(Qty. 16)
(Qty. 2)
(Qty. 4)
(Qty. 2)
(Qty. 4) (Qty. 4)
(Qty. 2)
(Qty. 84) (Qty. 8)
S.M.S. (Qty. 8)
29 1/4-20 x 1 3/4”
Hex Hd. Bolt
Qty. 2
(Qty. 4)
1/4-20 x 2 3/4 Hex Head Bolt
#8 x 5/8 Sheet
Metal Screw
(Qty. 12)
A. An electric screwdriver is helpful in assembly. However, please set to low torque and use caution because you could
over-tighten the hardware and strip the screws.
B. Indentation mounting guides are small so look closely when attaching hardware.
C. Table top can be set on top of two saw horses. Although this will make assembly easier it is not necessary to complete
assembly. Always use shipping container to protect the painted surface of the table top.
CAUTION: Make sure that the table top is secure on sawhorses and NEVER leave the table top unattended.
ASSEMBLY TIPS
Sorting your hardware ahead of time will speed up assembly time. Sort all your
hardware now so it will be ready before you start assembly.
NOTE:
3

2. Align U-Support (#7) and U-Leg (#2) on Table
Top as shown in Figure 1.
1. Lay table top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the
painted surface of the table top.
End Rail Mounting
Indentations
Note: Indentations are
small so look closely.
1
2
13
7
3. Put plastic caps (#13) on the end of
U-Leg (#2). See Figure 1.
NOTE: “U-Leg” (#2) is larger and Wider
than the “U-Support” (#7). The U-Leg
should be installed on the end of the table
half with the end rail mounting holes.
(U-Support)
(U-Leg)
Note: U-Leg (#2) is larger and
Wider than the U-Support (#7).
1
Figure
Note: Indentations are
small so look closely.
ASSEMBLY TIP
The following pages will have a picture of the
Hardware Needed (to scale) along with the
Quantity, Key# and Description. You can lay the
hardware on the picture to identify the hardware.
ASSEMBLY TIP
Table top can be set on two saw horses. Although this will make
assembly easier it is not necessary to complete assembly. Always use
shipping container to protect the painted surface of the table top.
CAUTION: Make sure that the table top is secure on the
sawhorses and NEVER leave the table top unattended.
CAUTION:
4

4.
Align the holes in the U-clips #3 with the
indentations in table top assembly and secure
with four screws #20 per U-clip as shown. All
four holes in each U-Clip must align with four
Indentations in top. See Figure 2, Detail A and
Detail B.
20
3
IMPORTANT:
Slot in
U-Clip
Detail A
Be sure that slot in the three U-clips #3 all
face the same direction as shown. (Toward
the end of the table with no stripe.)
5
3
Be sure that slot in the three U-clips
#3 all face the same direction as
shown. (Toward the end of the
table with no stripe.)
Slot in
U-Clip
3
20
Detail B
7
2
3
7
Note: U-Leg (#2) is Taller and
Wider than the U-Support (#7).
Make sure they are assembled
exactly as shown. If not, there will
be a large gap between table
halves and table will not operate
properly!
(U-Support)
(U-Leg)
(U-Support)
Note: This is the end of the table
with no stripe or indentations.
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS
(#3) BE TURNED AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY,
YOU WILL DO IRREPARABLE DAMAGE TO YOUR TABLE WHEN YOU ATTEMPT
TO OPEN IT TO THE PLAYING POSITION.
2
Figure
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
20
HARDWARE NEEDED
#8 X 7/16” Screw
(Qty. 24)
IMPORTANT:
NOTICE
NOTICE

5. Lay out Side Rails #25 and End Rail #26, around edges
of table top as shown in Figure 3.
6. Slide Left #33 and Right #32 Vinyl End Caps onto the
ends of the Side Rails #25 as shown in Detail C.
7. Line up holes in rails with indentations in top
and secure using eighteen screws #20. See
Figure 3 & Detail C.
8. Lay Corner Caps #22 on table as shown in
Figure 3. If Corner Cap sticks above the
table top surface of the table, flip over so
the shorter distance is against edge. Secure
to bottom of table with three Screws #21.
See Detail D.
25
26
21
25
Note: Rails attach
with #20 screws
7
Note: Rails attach
with shorter #20
screws
20
33 (LH)
20
Detail C
Shorter Distance
Detail D
Longer Distance
20
32
(RH)
3
Figure
20
HARDWARE NEEDED
#8 X 7/16” Screw
(Qty. 18)
20
HARDWARE NEEDED
#8 X 5/8” Screw
(Qty. 6)
21
Note: This is the end of the
table with no rails.
Shorter Longer
Note: Corner Caps
attach with longer
#21 screws
20
6
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
NOTICE

2
19
3
7
Detail E
Note: Wear safety glasses for Step 9.
If you want to see a video on how to insert Screw (#19) go to:
http://www.escaladesports.com/customer-service/videos.html
7
9. Insert Screw #19 through slot in U-Clip #3 and the into U-
Support #7. Thread it all the way into U-Support #7 until it
touches the back of the tube. There should be about 3/8
inch of screw #19 left sticking out. Do not insert screw in
middle #3 U-Clip. See Figure 4 and Detail E. Repeat
for U-Leg (#2) and U clip (#3). See Detail F.
Or
Scan with your smartphone:
Note: Rotate U-Support #7
until you see the screw hole in
the slot of U-clip #3. Slide U-
support #7 side to side and
front to back if necessary.
19
3
2
Detail F
Note: Rotate U-leg #2 until
you see the screw hole in
the slot of U-clip #3. Slide
U-leg #2 side to side and
front to back if necessary.
Note: Rotate U-Support #7 until you see the screw
hole in the slot of U-clip #3. Slide U-support #7 side
to side and front to back if necessary.
4
Figure
20
HARDWARE NEEDED
19
HARDWARE NEEDED
#8-32 X 1 1/4
Phillips Head Screw
(Qty. 4)
DO NOT insert Screw
#19 in middle #3 U-clip.
DO NOT insert Screw
#19 in middle #3 U-clip.
7

7
4
Detail G
Figure 5A
First Table Top
12. Attach slotted end of safety strap #6 to INSIDE of Leg #2
using one bolt #29, one spacer #30, one washer #24, and
one hex nut #15. Tighten hardware until snug but do not
overtighten. Tubes must pivot freely. See Detail H2.
Important! Do NOT put other
safety strap #6 on this table
half. It will be installed on
second table half later.
23
4
15
31
2
4
15
1/4” Locknut
(Qty. 3)
29 1/4-20 x 1 ¾” Hex Head Bolt
(Qty. 1)
1/4-20 x 2 ¾” Hex Head Bolt
(Qty. 2)
30
3/4” Spacer
(Qty. 2)
31
5/16” Spacer
(Qty. 2)
HARDWARE NEEDED
24 Plastic Washer
(Qty. 2)
1/4-20 x 1 1/2 Bolt
(Qty. 1)
9
HARDWARE NEEDED
15
23
29 30
24
15
4
(Longer)
(Longer)
31
Detail H2
30
6
924 4
Detail H1 15
10. Attach safety strap #6 to linkage #4. Be sure to attach on the end of
linkage with TWO holes. Use one bolt #9, one washer #24, one
Spacer #30, and one hex nut #15. See Detail H1.
Note: This is the end of the
table with no rails.
11. Attach end of linkage #4 with the attached Safety Strap #6 INSIDE of
U-Leg #2 as shown in Detail H2. Secure through end hole with bolt
#23, Spacer #31 and locknut #15. Tighten hardware snug enough to
keep table stable but do not overtighten. Tubes must pivot freely.
2
2
13. Attach linkage #4 INSIDE other end of U-Leg #2 as
shown in Detail G. Secure through end hole with bolt
#23, plastic spacers #31 and locknuts #15. Tighten
hardware snug enough to keep table stable but do not
overtighten. Tubes must pivot freely.
6
8

14. Tap caster sockets #12 into U-support #7 until flange on
sockets touches the edge of the tube. See Figure 5B.
15. Insert casters #11 into caster sockets #12.
DO NOT HIT CASTER SOCKET #12 DIRECTLY WITH
A HAMMER! SET A PIECE OF WOOD ON CASTER
SOCKET AND HIT PIECE OF WOOD TO DRIVE
CASTER SOCKET INTO U-SUPPORT #7.
11
12
7
First Table Top
Note: This is the end of the
table with no rails.
Figure 5B
NOTE:
9

16. Attach other end of linkages #4 to OUTSIDE of U-support #7 with
bolts #14 and plastic washers #24. Then slide name panel #5
onto the same bolts #14 on the INSIDE of U-support #7. Secure
with lock nuts #15 See Figure 5C. Tighten hardware until snug but
do not overtighten. Tubes must pivot freely.
17. Attach bottom of name panel #5 to U-supports #7. Secure with
hex bolts #9 and locknuts #15. Tighten nuts but be careful not
to crush tubes. See Figure 5C.
18. Prepare an area for the assembly of the second
table top half. If necessary, move the first table top
half aside with the aid of a helper. Be sure to place it
in a location where it won't be disturbed or
damaged. If setting on its side, be sure to place the
bottom edge no less than 12 inches away form the
wall. Also be sure to place carpet or pieces of the
shipping carton down to protect table top edges. If
floor is not carpeted, brace table top half with a
heavy object to keep it from sliding.
CAUTION:
AT LEAST TWO ADULTS ARE NEEDED TO
MOVE TABLE HALF!
15
24
14
9
9
14
24
15
5
4
First Table Top
7
4
5
Figure 5C
24
¼” Locknut
(Qty. 4)
14 1/4-20 x 2” Hex Head Bolt
(Qty. 2)
15
HARDWARE NEEDED
Plastic Washer
(Qty. 2)
1/4-20 x 1 1/2 Bolt
(Qty. 2)
9
Logo on
#5 panel
faces out
Logo on
#5 panel
faces out
10

19. Repeat steps from 1-15 on second half then continue on Step 20.
20. Attach linkages #4 to the OUTSIDE of U-support #7 on
second table half. Use bolts #14, plastic washers
#24 and hex nuts #15. See Figure 6.
NOTE: Tighten locknuts #15 finger tight only.
They will be removed when the two
table top halves are connected.
CAUTION:
AT LEAST TWO ADULTS ARE NEEDED TO
MOVE TABLE HALF!
NOTE: Tighten locknuts #15 finger tight
only. They will be removed when the two
table top halves are connected.
4
4
7
Second Table Top
Figure 6
24
¼” Locknut
(Qty. 2)
14 1/4-20 x 2” Hex Head Bolt
(Qty. 2)
15
HARDWARE NEEDED
Plastic Washer
(Qty. 2)
14 24
24
14
11

21. Make sure the legs on the first table top half (the half with the name panel #5) are open. With
one person on each side of the table, lift and set table half on its legs. Place table against a
wall as shown above to help stabilize table top half while second half is being attached. Be
sure there is enough room to connect second half.
22. Place a hex bolt #9 and a locknut #15 on floor next to caster wheels (on both sides of the table half) so they will be handy for the next step.
23. With a person on both sides of the second table half, slide the second table half against the first table half. Remove locknuts #15 from screws #14 on second table half
where U-support #7 and linkages #4 join. Align holes in name panels #5 (on first table half) with holes in U-supports (on second table half). Secure second table half to top
hole in name panel #5 using hex bolt #14 installed earlier and locknuts just removed. Secure second table half to bottom hole in name panel #5 with the two hex bolts #9
and locknuts #15 you placed on the floor earlier. Tighten locknuts snug but do not overtighten. These joints must pivot. At this point go back and tighten hex bolts #9.
BE SURE THE FIRST TABLE HALF YOU ASSEMBLED (WITH NAME PANELS #5
ATTACHED) IS STABLE AND AGAINST A WALL. DO NOT LEAVE TABLE HALF
STANDING UNATTENDED.
UNTIL THE TABLE HALVES ARE CONNECTED THEY WILL NOT STAND ON THEIR
OWN. IT IS RECOMMENDED TO HAVE THREE PEOPLE TO CONNECT TABLE
HALVES. TWO TO STABILIZE TABLE AND ONE TO BOLT TABLE TOGETHER.
9
14
15
5
9
15
1/4-20 x 1 1/2 Bolt
(Qty. 2)
1/4” Locknut
(Qty. 2)
HARDWARE NEEDED
Assembled in
previous step
Figure 3
Figure 3
Figure 7
CAUTION:
CAUTION:
12

24. Choose a name panel #5 on either side of the table and install
one safety latch #8 into the right-hand hole on that name panel
as shown in Figures 8 & 9. Use one screw #10 one washer
#17 and one hex nut #16. NOTE: Flange on safety latch
must extend over top of name panel as shown in Figure 8.
Safety latch must pivot freely.
25. Go to the other side of the table and install the second safety latch
into the right-hand hole on the other name panel #5. NOTE:
Safety latches must be attached diagonally across
from each other See Figure 9..
10
8
Figure 3
Figure 3
Figure 8
Figure 3
Figure 3
Figure 9
16
17
10
#10-24 X 3/4 Round
Head Screw
(Qty. 2)
#10-24 Lock Nut
(Qty. 2)
#10 Flat Washer
(Qty. 2)
Hardware Needed
INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE OF
TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY
LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!
CAUTION:
CAUTION:
13

TO OPEN:
1. Stand behind the table near the safety latch.
2. Hold table half with one hand and pivot safety latch enough to
allow the edge of the table half to pass over it.
3. While keeping an eye on the safety latch, pivot table half until it
moves past the safety latch. Once edge of table has passed over
safety latch, stop pivoting table half.
4. With both hands on the table half, center yourself along the table
half and lower the table half to the floor.
5. Repeat for the other table half.
TO CLOSE:
1. Lift table half upward and inward to vertical position.
2. Check to be sure that table half is locked in the safety latch.
3. Repeat for the other table half.
OPENING AND CLOSING INSTRUCTIONS
READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO
NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON
TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS
TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH
OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY
OR PROPERTY DAMAGE.
14
THIS IS A GAME TABLE. DO NOT SIT, STAND, LEAN, WALK OR JUMP
ON TABLE! FAILURE TO COMPLY WITH THIS CAUTION COULD
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
CAUTION:
CAUTION:

CARE AND MAINTENANCE
You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of
your new table.
THE TABLE TOP
The top (playing surface) of your table is made of particle board. Like all products made of wood, it can be affected by atmospheric changes in both
temperature and humidity. This may cause a slight sag or distortion as the top expands or contracts. This is normal and should not cause concern
as it does not detract from the play or utility value of the table. After assembly of the table, you can minimize the effects of temperature and humidity
changes by storing the table in the folded up position in a dry area when table is not in use.
STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme temperature changes can cause the wood to
warp, swell, crack or blister. When your table is not in use, it should be folded up in a dry area. Due to the nature of particle board, table top may
bow. Damp and humid conditions will amplify this. This is normal and will not affect playability of table.
CLEANING YOUR TABLE
To clean your table use a soft, damp (NOT WET) cloth only. To prevent damage to your table's playing surface, DO NOT USE ANY CHEMICALS,
ABRASIVE OR CLEANING PRODUCTS on your table's playing surface.
MAINTENANCE OF YOUR TABLE
Be sure to oil all moving parts of your table including the pivot points. This will insure the safety and ease of use of your table.
This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios or
similar areas can cause wood to warp, swell, crack or blister.
UNLEVEL FLOORS
If table does not seem level, it is probably due to uneven or unlevel floors. Set the table in its PLAYING POSITION and move table several inches in
different directions to find the best location for the table. If the floor is extremely unlevel, table may not play or operate properly. If table is high in
the center, shim up under the outer U-legs.
90 DAY LIMITED WARRANTY
®
This consumer warranty extends to the original consumer purchase of any ESCALADE SPORTS Product
(hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a period of ninety (90) days from the original
purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from
defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, IMPROPER SERVICE, FAILURE TO FOLLOW
INSTRUCTIONS PROVIDED WITH THE PRODUCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND
WORKMANSHIP.
WARRANTY PERFORMANCE: During the above ninety (90) day warranty period, ESCALADE SPORTS shall repair or replace with a
comparable model, and Product, or component thereof, which may prove defective under normal use and proper care, and which our
examination shall disclose to our satisfaction to be thus defective, please contact our Warranty Dept.
1-866-873-3528 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706 - Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-warranty Products. ESCALADE®
SPORTS strongly recommends that the Product is insured for value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF THIS SALE, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
THE ABOVE NINETY (90) DAY WARRANTY PERIOD. ESCALADE® SPORTS SHALL NOT BE LIABLE FOR LOSS OF USE OF THE
PRODUCT OR OTHER CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES INCURRED BY THE
CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or incidental damages, so the above
limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
15

REPLACEMENT PARTS LIST FOR MODEL NUMBER T8830
*PARTS IDENTIFIER ON NEXT PAGE.
Key# DescriptionPart # Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
2
2
12
4
2
2
2
2
6
2
4
4
4
4
16
2
2
8
84
12
4
4
8
4
2
1
1
2
4
4
2
2
4A-5467-00
8S-6610-03
2S-6879-10
8S-6605-04
2S-6780-03
2S-6428-01
8S-6755-03
2S-6264-03
WB-1094-00
1B-4049-01
2Q-6084-00
3M-6115-00
4C-0159-00
WB-1110-00
WN-1008-99
WB-1007-99
2N-0214-99
1B-4089-00
1B-6451-00
1B-6449-00
3M-6494-00
1B-4135-00
2B-6087-00
2S-6384-10
2S-6385-10
5A-6700-00
2L-4238-01
1B-6465-00
7B-6257-00
7B-6256-00
3M-4152-00
3M-4153-00
TABLE TOP BLACK
U-LEG
1” U-CLIP
LINKAGE
NAME PANEL
SAFETY STRAP
U-SUPPORT
SAFETY LATCH
1/4-20 X 1 1/2 HEX HEAD BOLT
#10-24 X ¾ PHIL ROUND HD. SCR
CASTER
CASTER SOCKET
LEG CAP
1/4-20 X 2 HEX HEAD BOLT
1/4-20 LOCKNUT
#10-24 LOCKNUT
#10 FLATWASHER
#8-32 X 1 ¼ SHEET METAL SCREW
#8 X 7/16 SHEET METAL SCREW
#8 X 5/8 HEX/PHIL HD SMS
CORNER CAP
1/4-20 X 2-3/4 HEX HEAD BOLT
PLASTIC WASHER
¾ SIDE RAIL - BLACK
¾ END RAIL - BLACK
NET AND POST KIT
OWNER’S MANUAL
1/4-20 X 1-3/4 HEX HEAD BOLT
5/16” SPACER
¾” SPACER
VINYL END CAP RH
VINYL END CAP LH
16
2L-4238-01

*PARTS IDENTIFIER ON PREVIOUS PAGE.
17 2L-4238-01
22
21
25
26
1
20
33
32
25
4
12
11
9
9
10
8
14
23
31
13
2
7
5
15
16
7
19 20
3
3
3
15
15
24
1
17
2
3
3
19
15
29
9
30
24
31
15
30 24
62
15
23
19
20
4
A
A
3
19

NÚMERO DE MODELO
T8830
M A N U A L D E L U S U A R I O
2015 Escalade Sports
2L-4238-01
Los productos Escalade® Sports se pueden fabricar y/o producir bajo las siguientes patentes.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Puede haber patentes en trámite. Una o más patentes mencionadas y/o en trámite pueden cubrir productos específicos.
Por favor no regrese este
producto a la tienda!
Contacte al departamento de servicio al cliente de Escalade® Sports:
Teléfono:1-866-873-3528 ¡Sin costo alguno!
Fax:[phone] ¡Sin costo alguno!
E-mail:[email protected]
“ S P O R T ”
M E S A D E T E N I S D E M E S A

Visite nuestra página Web:
www.escaladesports.com
1. Lea este manual cuidadosamente antes de empezar a ensamblar. Lea completamente cada uno de los pasos antes de empezar a
ensamblar cada paso.
2. Algunas partes pequeñas pueden ser empacadas dentro de las partes grandes. Verifique en el interior de todas las partes
y cartones antes de ensamblar o solicitar partes.
3. Para que el ensamblado le sea más fácil, utilice la lista de partes de la página 3 para la identificación y clasificación de
las partes y sus componentes. Busque los juegos de tornillos en todos los cartones. Todos los tornillos y sus componentes
no se encuentran en un sólo juego.
4. No ajuste las partes hasta que las instrucciones se lo indiquen. Si las partes se ajustan antes de lo indicado, es posible que los
orificios no queden alineados, resultando que las partes queden fuera de su lugar y fácilmente no coincidan. Deje las tuercas de seguridad
levemente flojas hasta que las instrucciones le indiquen ajustarlas.
5. Herramientas necesarias: Desarmador Phillips, dos llaves de 3/8” , dos llaves de 7/16” (Puede utilizar llaves de matraca con vasos de
3/8” y 7/16" son recomendados).
Guarde estas instrucciones y el recibo de pago en el caso de que tenga que contactar al fabricante para partes
de remplazo.
7.
6. Un destornillador eléctrico, puede resultarle muy útil para armar la mesa. Sin embargo, debe usarlo en baja potencia
y tener mucho cuidado de no ajustar en exceso.
Por favor no regrese este producto a la tienda!
SOLUCIÓN DE PROBLEMAS POR INTERNET ASISTENCIA TÉCNICA
PEDIDO DE PARTES POR INTERNET PREGUNTAS FRECUENTES
MÁS INFORMACIÓN SOBRE PRODUCTOS DE ESCALADE® SPORTS
C O N S E J O S A N T E S D E I N S T A L A C I Ó N
Contacte al departamento de servicio al cliente de Escalade® Sports:
Teléfono: 1-866-873-3528 ¡Sin costo alguno!
Fax: [phone] ¡Sin costo alguno!
E-mail: [email protected]
Apartado postal (sólo para correspondencia):
Escalade Sports
PO Box 889
Evansville, IN 47706
Prince (tm) es una marca registrada de Prince Sports, LLC.
© 2015 Prince Sports, LLC.
www.princetennis.com 2015 Escalade Sports
2L-4238-01
C O N S E J O S A N T E S D E I N S T A L A C I Ó N

IDENTIFICADOR DE TORNILLOS
NUM. DE
REFERENCIA
29
(Cant. 4)
#8-32 X 1-1/4
Tornillo S.M.S.
(Cant. 8)
1/4-20 X 2 3/4 Tornillo de Cabeza Hexagonal
1/4-20 x 1-3/4 Tornillo
de cabeza Hexagonal
Rondana de
Plástico
(Cant. 8)
#8 x5/8 Tornillo para
lamina de metal
(Cant. 12)
1/4-20 x 1-1/2 Tornillo
de cabeza Hexagonal
(Cant. 6)
Tornillo de Phillips
(Cant. 2)
1/4-20 x 2 Tornillo de
cabeza Hexagonal
(Cant. 4)
#10
Rondana
(Cant. 2)
Tuerca
de Seguridad
(Cant. 16)
Separador de 5/16”
(Cant. 4)
Tuerca
de Seguridad
(Cant. 2)
Tornillo para
lamina de metal
7
(Cant. 84)
Separador de 3/4”
(Cant. 4)
A. Un destornillador eléctrico, puede resultarle muy útil para armar la mesa. Sin embargo, debe usarlo en potencia baja
y tener mucho cuidado de no ajustar en exceso y dañar la mesa con los tornillos.
B. Los orificios de guía son muy pequeños, ponga atención cuando instalale las partes.
C. La superficie de la mesa se puede poner sobre de dos caballetes de carpinteria. Aunque esto hará más fácil ensamblar
la mesa, no es necesario para que pueda completar el ensamblado. Siempre utilice los cartones del empaque donde venía la mesa,
para proteger la superficie de la mesa pintada.
PRECAUCIÓN: Asegúrese de que el tablero de la mesa esté seguro sobre los caballetes y NUNCA deje la mesa sola.
CONSEJOS DE
INSTALACIÓN
Separando sus tuercas y tornillos antes de empezar reducirá el tiempo de instalación.
Separe las partes ahora para que este listo antes de empezar la instalación.
NOTA:
3