Escea AF700 User manual

630315_1 AF700 Builders and Architects Sheet
Product Dimensions
All outside dimensions taken from the appliance are
with the standos attached.
693mm
593mm*
711mm*
596mm
387mm
AF700 Information Sheet for Builders and Architects
Appliance Information
For further information or specications, visit the
technical section of our website www.escea.com
to view the latest product Installation Manual.
Specications
Heat Output 5-5.6 kW
Star Rating 3-4 stars
Gas Input/Consumption 22-25 MJ/hr
Gas Connection Rear right or front right, 1/2”BSP female thread
Gas Type Natural Gas / ULPG (NZ) / Propane (Aus)
Weight 45 kg
Room fan Yes
Flue Type Simpson Duravent Direct Vent (False Chimney)
Flexi Flue (Masonry)
Flue Size 6” mm Outer, 4” mm Inner (Direct Vent)
4” and 3” Flexi Flue (Masonry)
Power Requirement 3 pin earthed 230V power outlet +isolating switch
to be within 1.0m of rear right hand corner of the
appliance.
Smart Heat App Yes
*Slim Fascia Dimensions.
Distance from fireplace base
to Fascia face
False cavity Installation
Cavity Construction
Masonry Installation Requirements
The masonry install requires a spacer below the appliance
to allow room for the fascia to sit flush with the ground.
Cavity Base
This appliance MUST be fully supported on its
base. The base must extend over the entire area of
the underside of the appliance. The base must also
be levelled to prevent vibration from possible fan
imbalance. M5 Standos (circled in the diagram
below) may be used to screw in any feet with an
M5 thread to level the rear of the fireplace inside
the cavity. The base of the cavity must be strong
enough to support 75kgs.
Cavity Shape
The stando rails installed on the outside must only be re-
moved when being installed into a masonry cavity.
Note: a top is not required when creating the cavity
Height Width Depth
False Chimney
installation (top standos
must be adjusted to the
upright position)
600mm 695mm 390mm
+flue
clearances
Masonry install with
Stando Rails Removed
585mm 685mm 385mm
*Note: If cavity dimensions significantly exceed those spec-
ified, a register plate is available for purchase through your
local escea retailer (New Zealand Only).
D
H
W

630315_1 AF700 Builders and Architects Sheet
Vertically terminating flue diagram Horizontally terminating and vertically terminating with a
horizontal oset flue diagram
Flue Information
Mantle Clearances
Television clearances
The following are the recommended minimum clearances
for the location of any electrical equipment (such as
Plasma TV, LCD TV or home theatre) above an Escea
AF700 gas fire. Use either a shelf or mantle below your
TV screen or alternatively you can construct a recess to
mount your TV screen into.
Note: The television clearance recommendations below
are to be treated as a suggestion of a suitable installation
only. It is the responsibility of the end user to check the
installation instructions of their electrical appliances to
ensure that the location in relation to the gas fire is suit-
able. Escea in no way guarantees or takes responsibility
that the above installation suggestion will be suitable for
all electrical or home entertainment appliances.
Clearances
Flueing Clearances
25mm
=Minimum distance to combustibles
50mm 50mm 0mm*
50mm
50mm
>45°**
50mm
Ø75m m In t ake
Ø100mm Exhaust
50mm
25mm
25mm
600mm
300mm to
*Note Underside of converter box can be ?xed straight onto wooden
joist/nogging.
**Note: Flexi Flue must not be run at an angle greater than 45 degrees fro
m
vertical; excluding appliances built into a freestander kit.
Floor Clearances
If the appliance is mounted above a “hard floor” (includ-
ing but not necessarily limited to: wood, wood veneers,
ceramic tiles, concrete and stone) then it may be posi-
tioned with the bottom of the fascia coincident with the
finished floor if desired. Note: The appliance has been
tested and certified to AS4553:2008 and the maximum
allowable temperature rise above ambient of any com-
bustible floor is ΔT of 65C. Therefore any material used
must be chosen to be able to operate without damage or
degradation with a ΔT of 65C.
If the appliance is mounted above a “Soft floor” ” (includ-
ing but not necessarily limited to: carpets, Vinyl, carpet
tiles, rugs and mats) then we recommend a distance of
100mm from the bottom of the fascia to the finished
floor.
Hearth
A Hearth is not required, however it may be used for
decorative purposes or for protection of soft/sensitive
flooring as stated in the section above to allow a smaller
floor clearance. The hearth should not obscure the front
face of the fire, must protrude at least 200mm from
the face of the fireplace and be at least the width of the
appliance.
78 mm
Converter Box Dimensions
IMPORTANT : Refer to the installation manual for mandatory clearances from the terminal.