ESP EV4 User manual

EV4/EV4C
EV4KP/EV4CKP
VIDEO DOOR ENTRY SYSTEM
OPERATING INSTRUCTIONS

EV4/EV4C
Kit Contents:
1x Monitor
1x Outdoor Station (camera)
1x Power Supply (for handset)
1x Wall Bracket
1x Video connector lead
1x Power connector lead
System Requirements:
Maximum # of handsets: 4 videophones + 1 audio-only (EV4AO)
CAT5 cable: 50m
Alarm cable: 40m
BT twisted-pair telephone cable: 35m
(4 core minimum)
Door release requires the EV4-BPS (Boxed power supply). Suited for 12v DC mag or Yale locks only.
EV4KP/ EV4CKP
EVH4/EVH4C
1
www.espuk.com
Voltage: DC12-18V
Temperature: -20 < 55 *C
Stand by: 12mA
Working current: 600mA
Camera: 1/3 CCD lens
Illumination:0.05LUX
Mode: dual transmission
Talking time: 2 minutes
SCREEN
HANDSET
EXTENSION CALL TRANSFER
DOOR RELEASE
SPEAKER
CALL BUTTON
MIC
CCD CAMERA
LIGHT SENSOR
LED INDICATION
WATER COVER
ILLUMINATION LIGHT
CCD CAMERA
SPEAKER
CALL BUTTON
KEYPAD ACCESS

Indoor Monitor Connections
Red (Power)
Black (GND)
White (Audio)
Purple (Video)
Red
Black
White
Purple
Red
Black
PSU required for each monitor (max distance.20m)
2
www.espuk.com
EV4/EV4C
EVH4/EVH4C
EV4-BPS
PSU
PSU
EVH4/EVH4C
EV4KP/EV4CKP
EV4-BPS
To next monitor
(if required)
From outdoor
camera
System Wiring:

Keypad Programming Instructions
(EV4KP / EV4CKP Only)
Entering Programming Mode
Press the * (star) button followed by your 4 digit master code. Factory set
master code is 1234. A tone will be heard and red LED will start to ash,
once the LED is ashing you are now in programming mode.
To exit programming mode press the *(star) key.
Adding User Codes
Firstly enter programming mode.
Then enter a location 01 to 40 (31 –40 are the latching code locations).
Enter the desired 4 digit user code, a conrmation tone will be heard.
Press * (star) to exit programming.
Setting the Lock Time
The unit is factory set to 5 seconds, if the time needs changing, firstly
enter programming mode.
Enter location 00
Enter desired lock operation time in a two digit format e.g. 09 for 9
seconds, 30 for 30 seconds up to a max of 99 seconds
Press *(star) to exit programming.
Changing the Master Code
Remove power from the unit and press and hold down the star key.
Apply power whilst holding button down, the unit will give a long
continuous tone
When the tone has stopped , release the star key and enter your new 4
digit programmers code
3
www.espuk.com

ESP Product Range Codes
4
www.espuk.com
ENTERVIEW 4 Systems
EV4 Mono video door entry system
EV4C Colour video door entry system
EV4KP Mono video door entry system with keypad
EV4CKP Colour video door entry system with keypad
ENTERVIEW 4 Handsets
EVH4 Mono master / slave EV4 video handset
EVH4C Colour master / slave EV4 video handset
EVH4AO Audio only / slave EV4 audio handset
Power Supplies
EV4BPS 12 VDC 2 AMP multi output boxed power supply
Lock Releases
EV4ML-250 250kg Mag Lock c/w Z and L bracket
EV4ML-250M 250kg Monitored Mag lock c/w Z and L bracket
ENTERD 12VDC ush mount door strike
Exit Button
EV4EXIT 12VDC exit button for use with Enterview range
EV4EBG Surface mounting green call point "emergency door release"

Technical Support 01527 51 51 45
www.espuk.com