ETC High End Systems SolaWash 1000 User manual

Automated Luminaire
User Manual
Version 1.2 — Revision A

To view a list of ETC trademarks and patents, go to etcconnect.com/ip. All other
trademarks, both marked and not marked, are the property of their respective owners.
Information and specifications in this document are subject to change without notice.

Table of Contents
Table of Contents i
Introduction 1
Contacting High End Systems 1
Headquarters 1
Technical Support 1
FCC Information 1
Patents 1
Terms and Conditions and Warranty Information 1
Product Modification Warning 2
Mise En Garde Contre La Modification Du Produit 2
Produktmodifikationswarnung 2
Avvertenza Sulla Modifica Del Prodotto 2
Advertencia De Modificatión Del Producto 2
Important Safety Information 3
Fixture Overview 4
Dimensions 5
Safety Considerations 6
General Operation and Use Guidelines 7
Install the Fixture 8
Power 10
Input and Power Factor 10
Connector Specification 10
DMX Control 11
DMX Connector Pinout 11

Connect DMXCables to Fixture 12
DMX Control and Ethernet Output 12
Terminate DMX 12
Set the DMX Start Address 13
DMX Channels 13
Ethernet Control 14
Connect EthernetCables to a Fixture 14
Ethernet Control and DMX Thru 15
Set the DMX Start Address 15
Set the Control Input and Universe 15
Configure the Fixture 16
Navigate the User Interface 16
Set Fixture Parameters 17
DMX Address 17
Info Menu 17
Set Menu 19
Test Menu 22
Preset Menu 23
Error Codes 25
Cleaning and Maintenance 27
ii SolaWash 1000 User Manual

Introduction 1
Introduction
Congratulations on your purchase of the SolaWash 1000 automated fixture. This manual
provides important information for the safe installation, configuration, and maintenance of your
SolaWash 1000 fixture.
Contacting High End Systems
High End Systems, Inc. is an ETC company.
Headquarters
For Customer Service or Sales support, please contact our company headquarters:
2105 Gracy Farms Lane
Austin, TX 78758 USA
Tel: [phone]
Fax: [phone]
Toll-free: 800.890.8989
Website: highend.com
Technical Support
If you are having difficulties installing, configuring, or operating your SolaWash 1000, your most
convenient resources are the references given in this manual. To search more widely, try the
High End Systems, Inc. website at highend.com.
24-hour emergency support is available. Contact High End Technical Services at
[phone].
FCC Information
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his own
expense.
Patents
NOTICE OF INTELLECTUAL PROPERTY RIGHTS
High End Systems, Inc. products are protected by one or more patents listed on the High End
Systems, Inc. website: https://www.highend.com/patents and/or are subject to one or more
pending patents.
Terms and Conditions and Warranty Information
Complete terms and conditions and warranty information can be found on the High End
Systems, Inc. website:https://www.highend.com/pub/products/HES-Warranty-Information.pdf.

2 SolaWash 1000 User Manual
Product Modification Warning
High End Systems products are designed and manufactured to meet the requirements of the
United States and International safety regulations. Modifications to the product could affect
safety and render the product non-compliant to relevant safety standards.
Mise En Garde Contre La Modification Du Produit
Les produits High End Systems sont conçus et fabriqués conformément aux exigences de
règlements internationaux de sécurité. Toute modication du produit peut entraîner sa non
conformité aux normes de sécurité en vigueur.
Produktmodifikationswarnung
Design und Hestellung von High End Systems entprechen den Anforderungen der U.S.
Amerikanischen und internationalen Sicherheithsvorschriften. Abänderungen dieses Produktes
können dessen Sicherheit beeinträchtigen und unter Umständen gegen die diesbezüglichen
Sicherheitsnormen verstoßen.
Avvertenza Sulla Modifica Del Prodotto
I prodotti di High End Systems sono stati progettati e fabbricati per soddisfare i requisiti delle
normative di sicurezza statunitensi ed internazionali. Qualsiasi modifica al prodotto potrebbe
pregiudicare la sicurezza e rendere il prodotto non conforme agli standard di sicurezza
pertinenti.
Advertencia De Modificatión Del Producto
Los productos de High End Systems están diseñados y fabricados para cumplir los requisitos de
las reglamentaciones de seguridad de los Estados Unidos e internacionales. Las modificaciones
al producto podrían afectar la seguridad y dejar al producto fuera de conformidad con las
normas de seguridad relevantes.

Introduction 3
Important Safety Information
Please read all instructions prior to assembling, mounting, and operating this equipment.
Continued and safe operation of this fixture is the responsibility of the operator. This manual will
give tips for that continued safe operation. At any time please contact High End Systems
technical support for any safety concerns.
The following international note, caution, and warning symbols appear in margins throughout
this manual to highlight important messages.
Note: Notes are helpful hints and information that is supplemental to the main text.
CAUTION: This statement indicates that while operating, equipment
surfaces may reach very high temperatures. Allow the fixture to cool before
handling or servicing.
CAUTION: A Caution statement indicates situations where there may be
undefined or unwanted consequences of an action, potential for data loss or
an equipment problem.
WARNING: A Warning statement indicates situations where damage may
occur, people may be harmed, or there are serious or dangerous
consequences of an action
WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates
situations where there is a risk of electric shock.

4 SolaWash 1000 User Manual
Fixture Overview
For technical specifications of the SolaWash 1000 fixture, see the technical data sheet:
https://www.highend.com/documentation/SolaWash1000/SolaWash1000-Datasheet.pdf
1: Lens
2: Tilt lock
3: Display
4: [MODE/ESC] button
5: Left button
6: [Enter] button
7: Down button
8: Right button
9: Up button
10: Pan lock
11: Power in
12: Fuse
13: USB
14: DMX In
15: DMXThru
16: Ethernet
17: Ethernet
18: Handle

Fixture Overview 5
Dimensions
Dimensions shown are listed as inches [millimeters].
19.7in
[500mm]
12.7in
[324mm]
22.6in
[574mm]
11.1in
[282mm]
8.6in
[218mm]
17.5in
[444mm]
18.1in
[460mm]
28.6in
[726mm]
19.5in
[495mm]
4.7in
[118mm]
7.1in
[180mm]
23.8in
[605mm]

6 SolaWash 1000 User Manual
Safety Considerations
In order to ensure safe operation, follow the safety instructions and warning notes in this user
manual and any instructions from the manufacturer representative.
•
The SolaWash 1000 fixture is intended for professional use only. Not for residential use.
Read the entire manual before using this equipment.
•
Contact your High End Systems dealer or High End Systems technical support before
performing any service in order to maintain warranty coverage.
WARNING: For your safety, read the following warnings and notices
before use:
•
This equipment is designed for operation by qualified personnel only.
•
Disconnect the unit from power and DMX and data before servicing.
•
Replace fuses with the specified type and rating only.
•
Make sure that the available voltage is within the stated range.
•
NEMA Type 1 enclosure, indoor use, dry locations only. Do not use
outdoors. This fixture is intended for use where humidity does not
exceed 90% (non-condensing).
•
Do not use this fixture with a damaged power lead (cord set). If the
lead is damaged, it must be replaced by a qualified technician with an
equivalent type before use. Contact your local authorized dealer for
spare power leads.
•
Do not use this fixture if the lens, protection screen, or ultraviolet
screen is damaged. Damaged lenses must be replaced before use.
Contact your local authorized dealer for a replacement.
•
When the fixture has been stored or transported in cold temperatures,
allow it to warm to room temperature for a minimum of one hour
before applying power. Applying power to a cold fixture may cause
damage to the fixture and void the manufacturer warranty.
•
This is a Class 1 device and must be grounded. Follow national and
local codes.
•
Do not project the beam onto combustible substances.
•
Keep fixture head at least 0.1 m (0.33 ft) away from any flammable
materials.
•
Minimum distance to lighted objects:2 m (6.56 ft).
•
When you power on the fixture, you may notice smoke or odor. This is
normal and should decrease gradually. If smoke or odor persists,
disconnect the fixture from power and contact your High End Systems
dealer or High End Systems technical support.
WARNING: RISK OF ELECTRIC SHOCK! Do not operate this device with the
cover open.
CAUTION: Hot Surfaces. Allow the fixture to cool completely before
handling and servicing.

Safety Considerations 7
CAUTION: Damages caused by the disregard of this user manual are not
subject to warranty. The authorized dealer will not accept liability for any
resulting defects or problems.
General Operation and Use Guidelines
•
This fixture is only allowed to be operated with the maximum alternating current that is
stated in the technical specifications label provided on the fixture.
•
Lighting effects are not designed for permanent operation. Consistent operation breaks
may ensure that the fixture will serve you for a long time without defects.
•
Do not shake the fixture. Avoid brute force when installing or operating the fixture.
•
When choosing the installation location, make sure that the fixture is not exposed to
extreme heat, moisture or dust.
•
If using the supplied Omega brackets with quick-locking thumb screws for fixture hanging,
ensure that the thumb screws have engaged a complete 90-degree positive latch.
•
Operate the fixture only after having familiarized yourself with its functions. Do not permit
other persons who are not qualified and familiar with its functions to operate the fixture.
•
Please use the original packaging if the fixture is to be transported. ETC and High End
Systems, Inc. will not be responsible for the fixture if packaging other than manufacturer
provided packaging is used.
•
Do not modify the fixture. Any modifications will void the manufacturer warranty.
•
This manual describes the proper installation and operation of this fixture. Using this
fixture in any way other than the intended use may cause damage and may void the
factory warranty.
•
Misuse of this fixture or using it in a way different from the methods described in this
manual may lead to personal injury and/or equipment failure.
•
The light source of this fixture is not replaceable. When the light source reaches its end of
life, replace the fixture.
•
If you do not provide power to the fixture, the battery on the SolaWash 1000 may drain
fully after 7–10 days. After you provide power to the fixture, the battery will recharge
within 3–4 hours.

8 SolaWash 1000 User Manual
Install the Fixture
WARNING:
•
The installation location must support a minimum point load of 10
times the weight of the fixture.
•
The installation must always be secured with a secondary safety
attachment. An appropriate safety cable is supplied.
•
Safety cable attachment must be rated by a safety factor of 10.
•
Use of third party clamps are permitted, but they should comply with
the local jurisdiction and be approved by the Authority Having
Jurisdiction.
•
A supportive and stable surface must be used when the fixtures are
placed on the feet.
•
The operating temperature range for this fixture is -10°C–45°C (14°F–
113°F). Do not operate the fixture outside of this range.
•
Never stand directly below the installed fixture when mounting,
removing, or servicing the fixture.
•
All safety and technical aspects of fixture installation must be
approved by a qualified person before operation.
•
The installation must be regularly inspected by a qualified person.
•
Overhead rigging must be performed by qualified personnel.
CAUTION: Follow all local codes and recommended practices by the
Authority Having Jurisdiction. The installation must only be carried out by
qualified personnel.
You can install the fixture in any of the orientations shown below.

Install the Fixture 9
12
3 5
1. Assemble the clamp (provided by others) to the Omega bracket and secure together using
appropriately sized hardware (not provided).
2. Align the assembled Omega bracket and quick-lock fasteners into the respective holes on
the bottom of the fixture upper enclosure.
3. Tighten each of the quick-lock fasteners fully, turning clockwise. You will hear and feel a
click when the fastener is fully secured.
4. Repeat steps 1 through 3 for the second clamp and bracket.
5. Attach the provided safety cable through the attachment point on the bottom of the
fixture upper enclosure and secure to the trussing system or other safe installation point.
Follow local codes and recommended safety standards for securing the fixture to the
installation location.
6. Attach the fixture to the installation location using the installed clamps, using the clamp
manufacturer's instructions for a secure fit. When using the Omega clamp, close the
safety and fully tighten the clamp wing nut until secure.
7. Inspect the installation prior to lifting the fixture overhead.

10 SolaWash 1000 User Manual
Power
Input and Power Factor
VAC Amps Hz Watts VA PF
100 9.7 50 967 973 0.99
120 7.8 60 930 937 0.99
200 4.6 50 896 921 0.97
208 4.5 60 898 922 0.97
220 4.2 50 930 920 0.96
240 3.8 60 867 900 0.96
CAUTION: Using this fixture below 100 V on a 15 A breaker may cause the
breaker to trip. Ensure that the circuit can handle the fixture's maximum
potential draw before you connect it.
Connector Specification
A fixture power cord with powerCON TRUE1 input to bare end is provided. Install a suitable
connector to meet the installation requirements. See the following wire color code chart:
Wire Color Code (EU) Wire Color Code (US Standard) Connection type Terminal
Green/Yellow Green Earth/Ground
Blue White Neutral N
Brown Black Line (Live) L
WARNING: RISKOFELECTRICSHOCK! The powerCON TRUE1 is a
connector system consisting of the cable connector and the chassis
receptacle. A cable connector inserted the incorrect way could, in some
circumstances, lead to contact between live wires and the grounding contact
in the plug socket resulting in equipment malfunction and/or personal
injury.
Check the condition of your powerCON TRUE1 connector system (cable
connector and chassis receptacle) for clear signs of wear and tear.
Reference the Neutrik Safety Notice powerCON TRUE1 for more safety
information.

DMX Control 11
DMX Control
The SolaWash 1000 fixture operates on standard DMX512 control bus, controlled by a DMX
console. The fixture requires 37 channels of DMX512 in standard mode.
Attach the fixture to the control bus using a two-core, shielded cable with a 5-pin XLR connector
(Belden 9729 is preferred).
Two XLR termination receptacles are available: one for connection of DMXInput, and one for
DMXThru (used when daisy-chaining to additional fixtures on the DMX control bus).
DMX Connector Pinout
For DMXInput, the DMX cable must have a male XLR connector on one end of the cable. When
daisy-chaining DMX, the other end of the cable must have a female XLR connector. Terminate
the cable ends as indicated in the pinout image below.

12 SolaWash 1000 User Manual
Connect DMXCables to Fixture
The following instructions are guidelines for connecting DMX to your fixture. Your installation
may vary.
1. Connect the male XLR connector of a DMX data cable to the DMXThru connector on the
DMX control source.
2. Connect the female XLR connector of the DMX data cable to the DMX In connector of the
first fixture on the DMX control run.
3. Continue linking the remaining fixtures by connecting a cable from the DMXThru
connector of a fixture to the DMXIn connector of the next fixture on the control run.
Note: A maximum of 32 DMX devices may be connected in any one DMX data run
when installed in a daisy-chain fashion.
DMX-512
(Belden 9729 or equivalent)
terminate DMX
with a 120 Ohm
resistor
DMX-512
control
source
DMX Control and Ethernet Output
You can use DMX-512 control and Ethernet output. When a fixture is set up to receive DMX-512
control input, it converts the signal to ArtNet on IP10 and sends the signal to the Ethernet port,
continuing the ArtNet on IP10 signal to the next fixture in the control run.
Terminate DMX
For installations with a long DMX control run or an electrically noisy environment, we
recommend that you use a DMX terminator or install a resistor on the last fixture of the
DMXcontrol run to prevent corruption (data reflection) of the digital control signal by electrical
noise.
A DMXterminator is an XLR plug with a 120 Ωresistor connected between pins 2 and 3 that can
be installed into the DMX output receptacle of the last fixture in the DMX control run. This plug
is available and sold separately. Contact your local High End dealer for ordering information
(visit highend.com/about/contact-us to locate a High End dealer).

DMX Control 13
Set the DMX Start Address
Give each fixture a unique DMX starting address so that the correct fixture responds to the
control signals. This DMX start address is the channel number from which the fixture starts to
“listen” to the digital control information sent out from the control source.
Modify the fixture DMX start address on the user interface, located on the upper enclosure. See
DMX Address on page17 .
Example: The SolaWash 1000 has 37 channels. If you set the DMX starting address
of the first fixture to 1, you could set the second fixture to 38 (37+1), the third to 75
(38+37), and so on.
DMX Channels
The most current DMX Map data for the SolaWash 1000 can be found on the High End Systems,
Inc. website:
https://www.highend.com/documentation/SolaWash1000/SolaWash1000-protocol.pdf

14 SolaWash 1000 User Manual
Ethernet Control
The SolaWash 1000 fixture includes two Ethernet ports that allow sending and receiving of
control signals using the Art-Net protocol or sACN.
Use a Cat5e (or better) cable and terminate to RJ45 connectors following the TIA/EIA 568B
wiring standard.
Connect EthernetCables to a Fixture
The following instructions are guidelines for connecting Ethernet to your fixture. Your
installation may vary.
1. Connect a cable from the Ethernet control source to one of the Ethernet ports on the first
fixture in the Ethernet control run.
2. Connect the first fixture to a second fixture by connecting a cable from the second
Ethernet port on the first fixture to one of the Ethernet ports on the second fixture.
3. Continue linking the remaining fixtures by connecting a cable from Ethernet port to
Ethernet port on the fixtures on the control run.
Note: The Cat5e cable distance should not exceed 100 m, and you should not
connect more than 20 fixtures in one Ethernet control run when the fixtures are linked
together.
Cat5e or better
Ethernet
control
source

Ethernet Control 15
Ethernet Control and DMX Thru
You can use Ethernet control and DMX Thru. When a fixture is set up to receive Ethernet control
input, it automatically distributes DMX via the DMX Thru port. The DMX-512 signal is sent as a
single universe that corresponds to the universe of the fixture that is receiving Ethernet control.
Ethernet
control
source
Universe 1 Universe 1 Universe 1
Set the DMX Start Address
Give each fixture a unique DMX starting address so that the correct fixture responds to the
control signals. This DMX start address is the channel number from which the fixture starts to
“listen” to the digital control information sent out from the control source.
Modify the fixture DMX start address on the user interface, located on the upper enclosure. See
DMX Address on page17 .
Example: The SolaWash 1000 has 37 channels. If you set the DMX starting address
of the first fixture to 1, you could set the second fixture to 38 (37+1), the third to 75
(38+37), and so on.
Set the Control Input and Universe
For Ethernet control, you must configure the control input (Art-Net on IP2, Art-Net on IP10, or
sACN) and set a universe (000-255) for each fixture. See Select Input on page20 and Set
Universe for Art-Net on page20 for details.

16 SolaWash 1000 User Manual
Configure the Fixture
You can configure SolaWash 1000 fixtures through the onboard user interface.
Navigate the User Interface
Mode
Esc.
1. Press the [MODE/ESC] button (
Mode
Esc.
) to access the main menu. (The display is powered by
battery when the fixture has no power.)
2. Browse the menu by pressing the up, down, left, or right navigation buttons.
3. Press the [Enter] button ( ) to select a menu item.
4. Modify the selection by pressing the up, down, left, or right navigation buttons according
to the selection.
5. Press the [Enter] button ( ) to confirm a modified selection.
6. To exit the menu, press the [MODE/ESC] (
Mode
Esc.
)button.
Note: If you press the [Enter] button to confirm a selection and push no other buttons,
the user interface returns to the default display after 15 seconds.