Etc Source four led series User manual

USER’SGUIDE

SourceFourCDMGoboprojector

withremotemagneticcontrolgear

CONTENTS

Beforeyoustart 2

Mounting&connectingtheremotecontrolgear 3

Installingthelamp 4

Focussingtheluminaire 4

Usingcolourfilter 4

LampReplacement 5

Routinemaintenance 5

SourceFourCDMdiagram 6

Warranty 7

Specifications 7

www.enliten.co.uk/manuals/S4CDM.pdf

Page 1

Thispageisleftintentionallyblank

Before you start

This package contains a Source Four CDM profile spotlight with remote (2m)magnetic control gear.

Ensure that you have the correct fixture (5°, 10°, 19°, 26°, 36°, 50°) –this will be indicated on the carton.

In addition to the luminaire you will also have been supplied with;

Ensure that you have control gear to match the lamp wattage. Ensure that you have the correct colour temperature

lamp (see lamp replacement for further details)

Unpack & check for damage.

The Source Four CDM luminaire box should contain;

1 x Source Four CDM luminaire fitted with special lampholder assembly

1 x Hex Key

1 x Colour filter holder

If ordered with the fixture, other items including iris diaphragm, pattern holders and patterns may be included or

fitted. Please consult your box label and packing list for details.

Safety Information

This fixture is for professional use only. Read the entire manual before use.

•Do not mount this fixture on or near a flammable surface

•This fixture is for interior use only –for exterior applications use Callisto Exterior spotlight

•We recommend the use of a safety cable as a secondary suspension

•Always ensure that the colour frame clip is left in the locked position

•Always replace the lamp if it is damaged or thermally deformed or is slow to start

•Keep luminaire 0.7m from any lighted object

•Disconnect the luminaire from power before cleaning, maintenance or re-lamping

•Maximum ambient temperature ta=45°C

•Maximum surface temperature tmax=180°C

70/150W Magneticremote control

gear to suit local supply voltage

and frequency

Philipsmastercolour

70/150W CDM-T lamp

Page 2

WarrantyWarranty

Enlitenwarrantsthattheluminaireshallbefreefrommanufacturingdefectsinmaterialsandworkmanship.

Allluminairesaretestedandinspectedfordamagepriortoshipping.

Anyclaimunderthewarrantyshouldbemadetothedealerthatsuppliedtheequipmentalongwithacopyoftheinvoice

and details of the problem. Should you be unable togetasatisfactoryresponsefromyourdealer,ortheyarenolonger

trading, please contact Enliten directly enclosing in addition, copies of any intermediate correspondence with your

dealer.

ThiswarrantyisalimitedwarrantyandisgivenunderEnglishLawsubjecttothefollowing(notwithstandinganystatutory

requirements);

1. Enliten shall be under no liability in respect of any defect in the Goods arising from any drawing, design or

specificationsuppliedbyothers

2. Enliten shall be under no liability in respect of any defect arising from fair wear and tear, wilful damage

negligence,abnormalworking conditions, failuretofollowEnliten’s instructions (whetheroralorin writing),

misuseoralterationorrepairoftheGoodswithoutEnliten’swrittenapproval

3. Subject as expressly provided in these Conditions, and except where the Goods are sold under a consumer

sale (as defined by the UK Sale of Goods Act 1979), all warranties, conditions or other terms implied by

statuteorcommonlawareexcludedtothefullestextentpermittedbylaw.

4. Any claim which is based on any defect in the quality or conditions of the Goods shall (whether or not

delivery is refused by the Buyer) be notified to the dealer within 7 days from the date of delivery orwhere

thedefectorfailurewasnotapparentonreasonableinspection)withinareasonabletimeafterdiscoveryof

the defect or failure. If delivery is not refused, and the Buyer does not notify the dealer accordingly, the

BuyershallnotbeentitledtorejecttheGoodsandEnlitenshallhavenoliabilityforsuchdefectorfailure

5. Exceptinrespectofdeath or personal injury causedbyEnliten’snegligence,Enliten shall not be liabletothe

Buyer by reason of any representation, or any implied warranty, condition or other term or any duty at

commonlaw,orunder the expresstermsofthe Contract, for anyconsequentiallossor damage (whether for

loss of profit or otherwise), costs, expenses or other claims for consequential compensation whatsoever (and

whether caused by the negligence of Enliten, its employees or agents or otherwise) which arise out of or in

connection with the supply of the Goods or their use or resale by the Buyer, except as expressly provided in

theseConditions.

SpecificationsSpecifications;

Packed Size Max Voltage See control gear

Packed Weight Max Current See control gear

Lamp Type Philips CDM-TMinimum service interval 6 months

Lamp Wattage 70W or 150W Pattern Type B size glass or metal

Rated Lamp Life 9000hr Ballast Type To suit CDM-T

Lamp Base G12 IP Rating IP20

Special Tools Required Hex Key (supplied)

Conformity UL, CE EN60598

Page 7

Mounting and connecting the remote control gear

Mount

the fixture first in its final location. A number of mounting brackets are available from your dealer. We

recommend the use of a secondary suspension cable which is also available from your dealer in both black and

galvanised finish.

The Source Four CDM

is supplied with a 2m high voltage flex that must be connected to the remote encapsulated

control gear. If for any reason another control gear package is used, it must be of a type approved by Philips for use

with the CDM-T mastercolour lamp and must mee

t all local electrical codes. If in doubt, please contact Enliten for

advice.

Do not extend the luminaire flex

-itisa specialhighvoltagecabletypeandthemaximumpermitteddistance

between the fixture and remote encapsulated gear is 2m/6ft*

you must place the control gear more than 2m from the fixture, you should contact your dealer and upgrade the

control gear package to a 20m long range IP65 control gear package.

You should now securely mount the remote control gear in a suitable location

such that the luminaire flex will easily

reach the output terminals. The location must be ventilated to ensure that the ambient temperature does not rise

above 50°C.

You may now connect the luminaire to the control gear package

The installation and co

nnection of a Source Four CDM system to a mains supply should be carried out by a competent

electrician and all work should be carried out to local regulatory standards.

The connections are as follows;

Fixture to ballast

HT/Live –Brown with white inner insulation

Neutral –Blue with white inner insulation

Earth/Ground –Green/Yellow

The Source Four CDM is a Class II (earthed) fixture and must be earthed/grounded even when connected to a Class I

(double insulated) control gear package.

Page 3

Source Four CDM DiagramSource Four CDM Diagram

Page 6

Useblackwireto

select voltage

[230]

[250]

[240]

230/240/250V

50Hz

Installing the lamp

Ensure that the power is isolated. Using the hex key provided, release the lampholder assembly and remove.

Without touching the glass envelope, push the lamp fully into the lampsocket ensuring that the reta

iningclips lockinto

place.

Replace the lampholder assembly and tighten with the hex key.

Focussing the luminaire

Pull all of the shutter blades outwards to produce a circular beam. The beam may be focussed by releasing the focus

screw on the underside of the lens barrel and sliding the barrel backwards or forwards.

The beam may be shaped or masked by adjusting the shutter blades.

An A size (100mm dia) or B size (86mm dia) metal gobo, glass gobo or dichroic coloured glass may be inserted into

either the gobo slot or the iris slot.

Note: The correct gobo holder must be used. If one has not been supplied, contact your dealer for details.

If using the iris slot for either an Iris diaphragm or a gobo,

the slot cover must be opened. Release the two screwsand

slide back the cover. Insert the accessory, close the cover as

far as it will travel and tighten the screws again with the

cover in the closed position. This retains the accessory within

the slot.

For fine adjustment of the gobo rotation, the entire front

barrel of the fixture may be rotated by releasing the

barrel rotation knob, and rotating the lens barrel.

Tighten the knob after use.

Using Colour Filters

There are three colour filter options available;

1. Use standard theatrical colour filter in the holder supplied

2. Use Devon Glass filter in the front colour runner

3. Use an 86mm or 100mm dichroic filter in a glass

gobo holder in the gobo or iris slot (not the same slot

as any other accessory)

Note that for 1 & 2, the filter holder must be secured by ensuring that the retaining clip is in the locked position.

Page 4

Lamp replacementLamp replacement

Approved lamp types;

Philips Mastercolour CDM-T lamp 150W 830 (3000K) or 942 (4000K) or 70W 830 (3000K) or 70W 942 (4000K)

The Philips 70W or 150W CDM-T 830 (

3000K) or 942 (4000K) lamp has a manufacturer’s rated life of 9000hrs. This is

a manufacturer’s rated life and is not a guaranteed life in real service. In practice it has been found that under

reasonable service conditions that this life expectancy is c

ommon. It has been noted that there may be a degradation

in light output over the life of the lamp, which can become noticeable after 6000hr. We do not currently recommend

the use of any other manufacturer’s lamp.

It is important to replace any lamp t

hat fails to ignite or begins to cycle (switching on and off continually). Although

the ballast (if using the recommended type) will have a thermal cut-

off and timed ignitor to protect against damage,

the life of the ignitor may be reduced.

Werecommend a planned annual maintenance and lamp change. This should avoid the need for occasional lamp

changes. In addition, you should assess the risk of accidental and deliberate damage, and the conditions under which

these fixtures are used, and plan additional maintenance as this risk assessment requires. It is often a statutory

requirement to keep a written record of your risk assessment and the measures employed.

The Philips CDM ceramic metal halide lamp has excellent colour rendering for a metal halide lam

p. The lamp will

reach its optimum output and stability after 100 hrs use. Before this time there may be a variation in colour

temperature and output. These phenomena may also occur when the position of the fixture is changed.

These effects are more noticeable with the 3000K 830 lamp types.

For installation of the lamp, please see the section Installing the Lamp above

Routine MaintenanceRoutine Maintenance

Routine maintenance should include cleaning the lenses with a dry lint free cloth, examination for any physical

damage, checking the tightness of the mountings, checking electrical connections.

The lamp should be replaced within its rated life of 9000hrs or when the light output begins to fall, or when the lamp

regularly fails to ignite within 30s of power-on.

ARNING: The Source Four CDM is rated to IP20 and therefore should only be used in an internal dry environment.

Routine maintenance procedures and intervals should be assessed on an individual basis based on the location, usage

and potential risks. This procedure should be documented as part of your site risk assessment.

Page 5

Installing the lampInstalling the lamp

Ensure that the power is isolated. Using the hex key provided, release the lampholder assembly and remove.

Without touching the glass envelope, push the lamp fully into the lampsocket ensuring that the reta

iningclips lockinto

place.

Replace the lampholder assembly and tighten with the hex key.

Focussing the luminaireFocussing the luminaire

Pull all of the shutter blades outwards to produce a circular beam. The beam may be focussed by releasing the focus

screw on the underside of the lens barrel and sliding the barrel backwards or forwards.

The beam may be shaped or masked by adjusting the shutter blades.

An A size (100mm dia) or B size (86mm dia) metal gobo, glass gobo or dichroic coloured glass may be inserted into

either the gobo slot or the iris slot.

Note: The correct gobo holder must be used. If one has not been supplied, contact your dealer for details.

If using the iris slot for either an Iris diaphragm or a gobo,

the slot cover must be opened. Release the two screwsand

slide back the cover. Insert the accessory, close the cover as

far as it will travel and tighten the screws again with the

cover in the closed position. This retains the accessory within

the slot.

For fine adjustment of the gobo rotation, the entire front

barrel of the fixture may be rotated by releasing the

barrel rotation knob, and rotating the lens barrel.

Tighten the knob after use.

Using Colour FiltersUsing Colour Filters

There are three colour filter options available;

1. Use standard theatrical colour filter in the holder supplied

2. Use Devon Glass filter in the front colour runner

3. Use an 86mm or 100mm dichroic filter in a glass

gobo holder in the gobo or iris slot (not the same slot

as any other accessory)

Note that for 1&2, the filter holder must be secured by ensuring that the retaining clip is in the locked position.

Page 4

Lamp replacement

Approved lamp types;

Philips Mastercolour CDM-T lamp 150W 830 (3000K) or 942 (4000K) or 70W 830 (3000K) or 70W 942 (4000K)

ThePhilips70Wor 150W CDM-T 830(

3000K)or942(4000K)lamphasamanufacturer’srated life of 9000 hrs.

Thisisamanufacturer’sratedlifeandisnot a guaranteed lifeinrealservice. Inpracticeithasbeenfoundthatunder

reasonableserviceconditionsthatthislifeexpectancyis

common. Ithasbeennotedthattheremaybea degradation

inlightoutputoverthelifeofthelamp,whichcanbecomenoticeableafter6000hrs. Wedonotcurrentlyrecommend

the use of any other manufacturer’s lamp.

It is important to replace any lamp t

hat fails to ignite or begins to cycle (switching on and off continually). Although

the ballast (if using the recommended type) will have a thermal cut-

off and timed ignitor to protect against damage,

the life of the ignitor may be reduced.

Werecommend a planned annual maintenance and lamp change. This should avoid the need for occasional lamp

changes. In addition, you should assess the risk of accidental and deliberate damage, and the conditions under which

these fixtures are used, and plan additional maintenanceas this risk assessment requires. It is oftena statutory

requirement to keep a written record of your risk assessment and the measures employed.

The Philips CDM ceramic metal halide lamp has excellent colour rendering for a metal halide lam

p. The lamp will

reach its optimum output and stability after 100 hrs use. Before this time there may be a variation in colour

temperature and output. These phenomena may also occur when the position of the fixture is changed.

These effects are more noticeable with the 3000K 830 lamp types.

For installation of the lamp, please see the section Installing the Lamp above

Routine Maintenance

Routine maintenance should include cleaning the lenses with a dry lint free cloth, examination for any physical

damage, checking the tightness of the mountings, checking electrical connections.

The lamp should be replaced within its rated life of 9000hrs or when the light output begins to fall, or when the lamp

regularly fails to ignite within 30s of power-on.

ARNING: The Source Four CDM is rated to IP20 and therefore should only be used in an internal dry environment.

Routine maintenance procedures and intervals should be assessed on an individual basis based on the location, usage

and potential risks. This procedure should be documented as part of your site risk assessment.

Page 5

Mounting and connecting the remote control gearMounting and connecting the remote control gear

Mount

the fixture first in its final location. A number of mounting brackets are available from your dealer. We

recommend the use of a secondary suspension cable which is also available from your dealer in both black and

galvanised finish.

The Source Four CDM

is supplied with a 2m high voltage flex that must be connected to the remote encapsulated

control gear. If for any reason another control gear package is used, it must be of a type approved by Philips for use

with the CDM-T mastercolour lamp and must mee

t all local electrical codes. If in doubt, please contact Enliten for

advice.

Do not extend the luminaire flexDo not extend the luminaire flex ––

itisaspecialhighvoltagecable typeandthe maximumpermitteddistanceitisaspecialhighvoltagecabletype andthemaximum permitteddistance

between the fixture and remote encapsulated gear is 2m/6ft*between the fixture and remote encapsulated gear is 2m/6ft*

you must place the control gear more than 2m from the fixture, you should contact your dealer and upgrade the

control gear package to a 20m long range IP65 control gear package.

You should now securely mount the remote control gear in a suitable location

such that the luminaire flex will easily

reach the output terminals. The location must be ventilated to ensure that the ambient temperature does not rise

above 50°C.

You may now connect the luminaire to the control gear package

The installation and co

nnection of a Source Four CDM system to a mains supply should be carried out by a competent

electrician and all work should be carried out to local regulatory standards.

The connections are as follows;

Fixture to ballast

HT/Live –Brown with white inner insulation

Neutral –Blue with white inner insulation

Earth/Ground –Green/Yellow

The Source Four CDM is a Class II (earthed) fixture and must be earthed/grounded even when connected to a Class I

(double insulated) control gear package.

Page 3

Source Four CDM Diagram

Page 6

Useblackwireto

select voltage

[230]

[250]

[240]

230/240/250V

50Hz

Before you startBefore you start

This package contains a Source Four CDM profile spotlight with remote (2m)magnetic control gear.

Ensure that you have the correct fixture (5°, 10°, 19°, 26°, 36°, 50°) –this will be indicated on the carton.

In addition to the luminaire you will also have been supplied with;

Ensure that you have control gear to match the lamp wattage. Ensure that you have the correct colour temperature

lamp (see lamp replacement for further details)

Unpack & check for damage.

The Source Four CDM luminaire box should contain;

1 x Source Four CDM luminaire fitted with special lampholder assembly

1 x Hex Key

1 x Colour filter holder

If ordered with the fixture, other items including iris diaphragm, pattern holders and patterns may be included or

fitted. Please consult your box label and packing list for details.

Safety InformationSafety Information

This fixture is for professional use only. Read the entire manual before use.

•Do not mount this fixture on or near a flammable surface

•This fixture is for interior use only –for exterior applications use Callisto Exterior spotlight

•We recommend the use of a safety cable as a secondary suspension

•Always ensure that the colour frame clip is left in the locked position

•Always replace the lamp if it is damaged or thermally deformed or is slow to start

•Keep luminaire 0.7m from any lighted object

•Disconnect the luminaire from power before cleaning, maintenance or re-lamping

•Maximum ambient temperature ta=45°C

•Maximum surface temperature tmax=180°C

70/150W Magneticremote control

gear to suit local supply voltage

and frequency

Philipsmastercolour

70/150W CDM-T lamp

Page 2

Warranty