Eterna AC44180 User manual

Issue 2013
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
Model:
LFT58WH / AC44180
LFT513WH / AC44181
LFT521WH / AC44182
LFT528WH / AC44183
T5 Linkable Fluorescent Fitting
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected].uk
Visit our website:
www.eterna-lighting.co.uk
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
For breakage information visit:
www.eterna-lighting.co.uk
Pack contents:
1 x Electronic uorescent tting
4 x Fixing screws
1 x Butt connector
2 x “C” mounting clips
2 x “F” mounting clips
1 x 2M Mains Lead
1 x 500mm Link Lead
LAMP SPECIFICATIONS: 21W 28W
Nominal Wattage 21W 28W
Rated Wattage 20.6W 27.9W
Average lifetime hours 24,000 hrs 24,000 hrs
Nominal useful luminous ux 1890 lm 2604 lm
Rated luminous ux 1890 lm 2604 lm
Luminous ecacy (Lm/W) in HF
operation 90 93
Rated lamp Lumen maintenance
in HF operation
2000hrs: 95%
4000 hrs: 92%
6000 hrs: 90%
8000 hrs: 90%
12000 hrs: 90%
16000 hrs: 90%
2000hrs: 95%
4000 hrs: 92%
6000 hrs: 90%
8000 hrs: 90%
12000 hrs: 90%
16000 hrs: 90%
Rated survival factors in HF
operation
2000hrs: 99%
4000 hrs: 97%
6000 hrs: 92%
8000 hrs: 92%
12000 hrs: 90%
16000 hrs: 90%
2000hrs: 99%
4000 hrs: 97%
6000 hrs: 92%
8000 hrs: 92%
12000 hrs: 90%
16000 hrs: 90%
Lamp dimensions (mm) 850mm 1150mm
Cap type G5 G5
Lamp Mercury content to an
accuracy of 0.1mg ≤2.7mg ≤2.7mg
Colour rendering index Ra ≥80 ≥80
Colour temperature 3500K 3500K
Ambient temperature required to
achieve maximum luminous ux 25°C 25°C
Dimmable No No

READ THIS FIRST:
Check the pack and make sure you have all of
the parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product contains glass, care must be taken
when assembling, tting or handling to prevent
personal injury or damage to the product.
This light tting must be installed by a
competent person in accordance with the
Building Regulations making reference to the
current edition of the IEE Wiring Regulations
(BS7671). The Building Regulations may be
obtained from OPSI (Oce for Public Sector
Information) or the department of Communities
and Local Government and viewed and
downloaded from www.communities.gov.uk
following the link for Building Regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
This product is designed and constructed according
to the principles of the appropriate British Standard
and is intended for normal domestic service. Use of
this tting in any other environment, for example
where prolonged periods of use may be expected
and/or higher than normal ambient temperatures,
may result in a foreshortened working life.
The lamps (tubes), supplied with this tting are
consumable parts and therefore may be outside of
any warranty oered.
This tting is not suitable for frequent use for
extended periods or in environments with higher
than normal ambient temperatures for example:
lighting public or shared spaces or in care facilities.
Switch o the mains before commencing
installation and remove the appropriate circuit fuse.
When working at heights, please use a suitable
platform.
Disconnect the HF ballast from the electrical supply
before ash or high voltage testing.
Suitable for indoor use only.
This product is suitable for use in living areas. It
is not suitable for bathroom or other areas where
contact with moisture is likely.
This product is suitable for installation on surfaces
with normal ammability (indicated by the “F” in a
triangle) e.g. wood, plasterboard, masonry. It is not
suitable for use on highly ammable surfaces (e.g.
polystyrene, textiles).
Before making xing hole(s), check that there are
no obstructions hidden beneath the mounting
surface such as pipes or cables.
Make sure that the xings are strong enough to
support the weight of the tting and hold it rigidly.
When choosing the location for your new tting,
give consideration to the ease and frequency of
lamp changes. The tting should not be installed in
a position where it will be dicult to reach,
Do not cover the tting.
The tting must be positioned so that there is at
least 10mm between the diuser and any other
surfaces.
If the location of your new tting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the
Building Regulations making reference to the
current edition of the IEE Wiring Regulations
(BS7671).
This product is designed for permanent connection
to xed wiring: this should be either a suitable
lighting circuit (protected with a 5 or 6 Amp MCB or
fuse) or a fused spur (with a 3 Amp fuse) via a fused
connection unit. We recommend that the supply
incorporates a switch for ease of operation.
Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
This tting is double insulated; do not connect any
part to earth.
This product is not intended to be used by children
and persons with sensory, physical and/or mental
impairments that would prevent them from using
it safely.
Small children should be supervised to ensure that
they do not play with this appliance.
IMPORTANT - Always switch o and isolate mains
supply to the ttings before changing the lamp(s).
If the external exible cable of this luminaire is
damaged it shall be exclusively replaced by an
qualied personnel.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specied in the Wiring Regulations
(BS7671) referred to in the Building Regulations.
874/2012
A
MODELNO.
LFT5 8W/13W
874/2012
A+
MODELNO.
LFT5 21W/28W
MODELNO.
A++
XXX kWh/1000h
8.80
8W
A
MODELNO.
A++
XXX kWh/1000h
14.30
13W
A
MODELNO.
A++
XXX kWh/1000h
22.66
21W
A+
MODELNO.
A++
XXX kWh/1000h
30.69
28W
A+

INSTALLATION:
01) When positioning the tting make sure there is a
gap of 10mm between the tting and any adjacent
surface. See Fig 1.
02) Select the type of brackets you need to use and
mark o the xing points see Fig.3 opposite
for best spacing. If xing to a shelf or under a
cupboard check the screw size required and screw
into place. See Fig. 2 and 3 opposite.
03) If xing directly to the wall, drill holes using an
appropriate drill bit to a depth of 30mm and insert
wall plugs.
04) Secure the selected brackets in place using the
screws supplied.
05) Attach the tting to the clips.
06) Connect the mains lead or link lead to the socket
on your tting.
07) Restore the power supply and switch on.
HOW TO LINK MULTIPLE FITTINGS
TOGETHER SEE FIG. 4:
Option 1. The light tting can be butted together to
form a line of up to a maximum of 6 ttings. Simply
remove the connector caps and push the ttings
together using the short butt connector supplied. Use
the mains lead cable to connect the rst tting and
the mains via a spur suitably fused.
Option 2. Connect link leads between each tting
once all lights have been connected; connect the
mains lead to the mains via a spur suitably fused.
WARNING:
The leads supplied with your tting and the sockets
incorporated in your tting are designed to give
protections against any possible electrical hazard. The
mains leads is terminated in a socket marked LS2S
and this lead should be used to supply mains to your
ttings or chain of ttings. Under no circumstances
should you attempt to adapt the link lead to supply
power to the opposite end of your tting as this will
leave live pins exposed at the mains input end of the
tting. Altering or adapting any of the leads, other
than shorting the mains supply lead, will invalidate
your guarantee and can present a severe electrical
shock hazard.
LAMP REPLACEMENT:
01) Switch o the electricity at the mains.
02) Lift o the diuser.
03) Rotate the lamp through approx 90° and withdraw
from the lamp holders.
04) Insert new lamp and rotate to lock in position.
05) Replace diuser.
06) Restore power and switch on.
LAMP REPLACEMENT TYPE:
8W requires 1 x 8W G5 T5 300mm uorescent tube
3500K (included) or energy saving alternative. Fitting
is rated at 8W max.
13W requires 1 x 13W G5 T5 525mm uorescent tube
3500K (included) or energy saving alternative. Fitting
is rated at 13W max.
21W requires 1 x 21W G5 T5 850mm uorescent tube
3500K (included) or energy saving alternative. Fitting
is rated at 21W max.
28W requires 1 x 28W G5 T5 1150mm uorescent tube
3500K (included) or energy saving alternative. Fitting
is rated at 28W max.
CLEANING:
Clean this light tting only with a soft dry cloth.
The diuser may be removed and washed in a
mild detergent solution. Make sure the diuser is
completely dry before putting them back on your
light tting.
Do not use any chemical or abrasive cleaners.
10mm Gap
End View
10mm Gap
End View
2M Mains Lead 500mm Link Lead
‘C’ Mounting Clip‘F’ Mounting Clip
1/4 1/42/4
Fixing Clips
Butt Connector
Up to 6 fittings can be connected together
End View
‘F’ Mounting Clip
End View
‘C’ Mounting Clip
10mm Gap
End View
10mm Gap
End View
2M Mains Lead 500mm Link Lead
‘C’ Mounting Clip‘F’ Mounting Clip
1/4 1/42/4
Fixing Clips
Butt Connector
Up to 6 fittings can be connected together
End View
‘F’ Mounting Clip
End View
‘C’ Mounting Clip
10mm Gap
End View
10mm Gap
End View
2M Mains Lead 500mm Link Lead
‘C’ Mounting Clip‘F’ Mounting Clip
1/4 1/42/4
Fixing Clips
Butt Connector
Up to 6 fittings can be connected together
End View
‘F’ Mounting Clip
End View
‘C’ Mounting Clip
10mm Gap
End View
10mm Gap
End View
2M Mains Lead 500mm Link Lead
‘C’ Mounting Clip‘F’ Mounting Clip
1/4 1/42/4
Fixing Clips
Butt Connector
Up to 6 fittings can be connected together
End View
‘F’ Mounting Clip
End View
‘C’ Mounting Clip
10mm Gap
End View
10mm Gap
End View
2M Mains Lead 500mm Link Lead
‘C’ Mounting Clip‘F’ Mounting Clip
1/4 1/42/4
Fixing Clips
Butt Connector
Up to 6 fittings can be connected together
End View
‘F’ Mounting Clip
End View
‘C’ Mounting Clip
10mm Gap
End View
10mm Gap
End View
2M Mains Lead 500mm Link Lead
‘C’ Mounting Clip‘F’ Mounting Clip
1/4 1/42/4
Fixing Clips
Butt Connector
Up to 6 fittings can be connected together
End View
‘F’ Mounting Clip
End View
‘C’ Mounting Clip
10mm Gap
End View
10mm Gap
End View
2M Mains Lead 500mm Link Lead
‘C’ Mounting Clip‘F’ Mounting Clip
1/4 1/42/4
Fixing Clips
Butt Connector
Up to 6 fittings can be connected together
End View
‘F’ Mounting Clip
End View
‘C’ Mounting Clip
Fig 2
Fig 3
Fig 4
Fig 1