Eterna vnanobh User manual

Model:
VNANOBH
8W LED Nano Bulkhead
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
874/2012
MODELNO.
VNANOBH
Pack contents:
1 x LED bulkhead
1 x Fixing kit
Email: [email protected].uk / [email protected].uk
Visit our website: www.eterna-lighting.co.uk Made in ChinaIssue 0617
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Clean this tting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
LED LAMP SPECIFICATIONS:
Luminaire lumens (with
diuser) 700 lm
Lumens from chip (no
diuser) 750 lm
Rated Wattage 8W
Rated luminous ux 700 lm
Nominal life time of the lamp 30,000 hrs
Colour temperature 4200K
Number of switching cycles
before premature lamp
failure
>15,000
Warm-up time up to 60% of
the full light output Instant full light
Dimmable No
Nominal beam angle >120°
Rated power 8W
Rated lamp lifetime 30,000 hrs
Lamp power factor >0.5
Lumen maintenance factor at
end of nominal life >0.7
Starting time <0.5
Colour rendering >80
Colour consistency Within a six step
Macadam ellipse
Rated beam angle >120°
Voltage / Frequency 240V~50Hz
Not suitable for accent lighting

READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This product must be installed by a competent
person in accordance with the current building
and IEE wiring regulations.
As the buyer, installer and/or user of this product it
is your own responsibility to ensure that this tting
is t for the purpose for which you have intended
it. Eterna Lighting cannot accept any liability for
loss, damage or premature failure resulting from
inappropriate use.
Switch o the mains before commencing installation
and remove the appropriate circuit fuse or lock o
MCB.
This unit is suitable for indoor and outdoor use.
This product is designed for permanent connection
to xed wiring: this must be a suitable circuit
(protected with the appropriate MCB or fuse).
This product is suitable for installation on surfaces
with normal ammability e.g. wood, plasterboard
and masonry. It is not suitable for use on highly
ammable surfaces (e.g. polystyrene, textiles).
Before making xing hole(s), check that there are no
obstructions hidden beneath the mounting surface
such as pipes or cables.
When making connections ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product is double insulated; do not connect
either the blue/brown wires or any part to the earth
terminal.
You are advised at every stage of your installation to
double-check any electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out,
these tests are specied in the current IEE wiring and
building regulations.
LAMP REPLACEMENT: INSTALLATION:
Choose the location for your new light tting
according to the conditions listed opposite.
01) Isolate the mains before commencing installation.
02) Using the base as a template, mark the position of
the xing holes.
03) Undo the two screws holding the diuser in place
and unscrew the LED array.
04) Pierce the rubber grommet and thread the mains
supply cable through it.
NOTE: Do not make the holes in the grommet
too large. They should be tight on the cable to
ensure a water-tight seal.
05) Make the terminal connections:
Live (L), Neutral (N).
06) Replace the LED array and diuser.
07) Restore power and switch on.
The light source contained in this luminaire
shall only be replaced by the manufacturer,
service agent or a similar qualied person.
CAUTION, RISK OF ELECTRIC SHOCK.
The light source is designed to last the lifetime of the
luminaire.