ETS AP-160 User manual

AP-160
Operang instrucons
Thank you for buying our air cleaner. Each system is carefully manufactured and subjected
to a test run to ensure safety and reliability. Please read the instrucons carefully before
inial use and save them for future reference.
www.ets-products.com

2
Table of contents:
Test reports:
Scope of delivery Page 2
Speci ca ons Page 2
Test reports Page2
Areas of applica on Page 3
System overview Page 3
Installa on instruc ons Page 3
Commissioning Page 3
Control and display  elds Page 4
Remote control Page 5
Tuya app control Page 6
Maintenance and cleaning Page 11
Safety instruc ons Page 12
* Voltage and frequency depend on the standard of the country or region in which the devices
are used. Device data can be found on the product label. Use only devices that are intended for
your region.
Scope of delivery:
Air cleaner - 1, Power cable - 1, Opera ng instruc ons - 1, Remote control - 1
Speci ca ons:
The system has been microbiologically tested. The test reports can be called up with the
test number below on the Ins tute website (www.sgs.com). We would also be happy to
make them available to you if you need.
GZF20-017834-07 PM0.3 ·GZF20-017834-08 CADR
GZF20-017834-09 BACTERIA REMOVAL RATE
WiFi technology IEEE 802.11 b/g/n, 2,4 GHz
WiFi security WEP, WPA, WPA2
frequency 2,412 - 2,484 GHz
Transmission power < 20 dBm
Transmission range max. 50 m
Recommended surface 160 m²
Air volume 1300 m³/h
Mains voltage* 110 V / 230 V
Frequency 50 Hz / 60 Hz
Power 140 W
Dimensions (mm) 1216 x 600 x 345
Weight (kg) 54 kg
Ambient temperature 5 °C – 40 °C
Rela ve humidity < 80 %

3
Areas of applicaon:
System overview:
The system is equipped with a highly ecient ltraon and cleaning system including a me-
dical berglass HEPA lter (HEPA H14 nach EN 1822-1:2009), an acvated carbon lter, a
tanium oxide photocatalyst lter, a UV sterilizaon lamp with a 254-nm wavelength, and a
plasma generator.
ETS air cleaning systems are used to eecvely remove toxins, viruses, bacteria, pathogens,
dust, allergens, and odors from the ambient air.
1 Housing
2 Wheels
3 Acvated carbon lter
4 HEPA lter
5 Prelter
6 Air inlet grille
7 Interior cover
8 Display touchscreen
9 Control board
10 UV-C sterilizaon lamp
11 Air outlet
Installaon instrucons:
Commissioning:
The device must be freestanding during operation with space of at least 30 cm to the rear
and to both sides. The rear air inlet, the lateral sensors, and the front and rear air outlets
must remain free and may not be covered.
The systems are tested and delivered ready to operate. Remove any packaging and
protective film. Ensure that the mains voltage and frequency indicated on page 2 match
your mains voltage and use the power cable to connect the system to power.
8
1 2 3 4 5 61011
79 11

4
Numerical display:
PM2.5, time preset.
Status display:
Speed status display, air filter replacement display, sleep mode, automatic mode.
Function button:
As on a remote control.
Air filter replacement reminder:
Replacement reminder: The flashing icon on the device indicates that the HEPA filter
must be replaced.
Reset after replacement:
After replacing the HEPA filter, press the On/off button and the speed button simulta-
neously for five seconds. The machine emits a signal tone.
The icon no longer flashes. This means that the filter has been replaced and the dura-
tion of filter use re-calculated.
When the device is first used, the icon flashes as well.
Follow the same procedure as that for replacing the HEPA filter. The device begins re-cal-
culating the duration of HEPA filter use.
Control and display elds:

5
On/off
Sleep mode
Timer
Fan level „–“ Fan level „+“
Switch UV
sterilization on/off
Auto mode
Remote control
On/off:
Press the On/off button to switch on the device.
By default, the device runs at Fan Level 1 in manual mode.
Auto mode:
In automatic mode, the fan level is controlled automatically according to air quality.
Timer:
Shut-off time can be planned. After the set time, the air cleaner automatically switches off.
The planned time can be between one and nine hours.
Sleep mode
The mode has minimum wind speed, and the light is switched off. Only the night mode icon
is lit up.
UV sterilization:
Press the UV sterilization button to set the air cleaner to sterilization mode. The sterilization
icon is lit up. Press the button again to leave this mode.
Note:
1. Press the On/off button. The air cleaner switches on.
2. Press the fan speed button. At Level 1, the fan begins to operate
3. As necessary, increase fan power by repeatedly pressing the fan speed button.
4. Press the sterilization button. The UV lamp switches on
5. Press the sterilization button again to switch off the UV lamp.