EUCHIPS EUP135D-1W12V-0 User manual

100VAC-240VAC
47/63Hz
92%@230VAC,Full load
≥0.95@115VAC,Full load
Cold start,40A@230VAC
1.7Amax@230VAC
206*75*41mm（L*W*H）
IP20
-30℃~40℃
-40℃~85℃, 20-90%RH
90℃
EN50515, EN61000-3-2
EN61000-4-2, 3, 4, 5, 6, 8, 11; EN61547
EN61347, GB19510
L-N:1KV
I/P-O/P: 3000VAC/1min/5mA
Metal
30,000h@tc:80℃
1%-100% Dimming to off
±3%
70mVp-p
DALI Dimming / Touch-dim
>15,000 times
1
11.25A/12VDC/135W
<10%@230VAC, Full load
EUP135D-1W12V-0
Surge
Withstand Voltage
Safety Standards
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI Standard
EMC Eission
EMC Immunity
tc
Lifetime
Material
Dimming Range
Dimension
Net weight: 668g±5%/PCS; 18PCS/Carton;13kg±5%/Carton; Carton Size: 303*221*265mm(L*W*H)
Packing(weight)
IP Rating
Working Temp.
Storage Temp., Humidity
Dimming Type
Switch Cycle
3 yearsWarranty Condition
Turn on delay Time <1.5s, at230Vac (When the light begins to shine)
Efficiency
AC Current(max)
Inrush Current(max)
THD(full load)
Current(mA)/Voltage (VDC) Power(W)
R & N (Max)
Channel
Current Tolerance
Voltage
Frequency Range(Hz)
Power Factor
Short Circuit
Over current
Hiccup, recovers after fault condition is removed
Constant current limiting, recovers automatically after removed
Safety&
EMC
Others
Function
Model
Output
Input
Protection
DALI Constant Voltage Dimming Driver
Product Features
EUP135D-1W12V-0 (Product No.:102200071101)
1/2
User’s manual: 2019-9 www.euchips.com
Dimension(mm)
Technical Paramaters
Application
Wall Washer LED Strip Light LED Tube Underground Light AR111 Venture Light
· Single channel constant voltage, 12VDC output.
· Meet DALI Protocol IEC62386
· Wide range of input voltage 100VAC ~ 240VAC
· Support Touch-DIM function
· High efficiency up to 92%
· Built-in active PFC function
· Protections: Short circuit, Over current.
· IP 20 design
· Suitable for indoor LED lighting application
41
75
206
186
40.5

DALI Constant Voltage Dimming Driver
2/2
User’s manual: 2019-9 www.euchips.com
DALI Wiring
※The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions,
the function of the product shall prevail.Please contact us if you have any questions .
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75- 2.5mm²is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
0120 40 60 80 100 120 140 160 180 200 220 240 254
20
40
60
80
100
120
0
110 20 30 40 50
0.1
0.2
0.3
0.4
DALI Dimming Level
Output Current(%)
Push DIM(Touch DIM) DiagramDALI Diagram
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
Push DIM Function
1. Press the Push DIM (Touch DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.
2. Short press the Push DIM (Touch DIM) switch (<0.5s) to control the lamp on or off.
3. Long press the Push DIM (Touch DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Push DIM (Touch DIM) switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing
Push DIM (Touch DIM) switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
Dimming Curve
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
Push DIM Panel(Touch DIM)
LN
861 861 861
12V/24V
861 861 861
12V/24V
861 861 861
12V/24V
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
L
N
DALI Controller
861 861 861
12V/24V
861 861 861
12V/24V
861 861 861
12V/24V
100VAC-240VAC
N
L
DALI Signal Input
Input
OUTPUT

100VAC-240VAC
47/63Hz
92%@230VAC, 满载
≥0.95@230VAC, 满载
冷启动,40A@230VACC
1.7Amax@230VAC
206*75*41mm（长*宽*高）
IP20
-30℃~40℃
-40℃~85℃, 20-90%RH
90℃
EN50515, EN61000-3-2
EN61000-4-2, 3, 4, 5, 6, 8, 11; EN61547
EN61347, GB19510
L-N:1KV
I/P-O/P: 3000VAC/1min/5mA
金属
30,000小时@tc:80℃
1%-100% 变暗直至关闭
±3%
70mVp-p
>15,000次
1
<10%@230VAC, 满载
EUP135D-1W12V-0
浪涌
耐压标准
安全标准
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC 62386-207: 2009, DALI 1.0DALI 标准
电磁兼容
EMC抗扰度
tc
寿命
材质
调光范围
尺寸
包装尺寸(重量)
防水等级
工作温度
储存温度、湿度
调光方式
开关周期
3年质保
启动延时 <1.5s, at230Vac (当光线开始闪烁时)
效率
电流
浪涌电流
THD
电流/电压/功率
波纹
通道
电流公差
电压
频率
功率因素
短路
过流
关闭输出，排除故障后自恢复
故障消除后，输出电流自动恢复
安全
&
电磁
兼容
其它
功能
型号
输出
输入
保护
DALI恒压调光驱动器
产品特点
·单通道恒压输出，每通道 12V 直流输出
·符合DALI协议IEC62386
·宽电压输入 100-240VAC
·高效率：达到 92%
·保护：短路，过压，过流。
·短路保护，过载保护，过压保护，过温保护
· IP20，适用于室内LED灯具
EUP135D-1W12V-0 (产品代码:102200071101)
1/2
用户手册: 2019-9 www.euchips.cn
技术参数
尺寸(mm)
净重: 668g±5%/PCS; 18PCS/Carton; 13kg±5%/箱; 外箱尺寸: 303*221*265cm(长*宽*高)
11.25A/12VDC/135W
应用
洗墙灯 LED灯带 LED硬灯条 地埋灯 AR111斗胆灯
41
75
206
186
40.5
DALI / Touch-dim

DALI恒压调光驱动器
2/2
用户手册: 2019-9 www.euchips.cn
接线图
调光曲线
※ 本说明书内容如有更新，恕不另行通知。若您使用的产品功能与说明书不一致时，请以产品为准。如有疑问请与我们联系。
注意事项:
1、本产品请由具有专业资格的人员进行调试安装。
2、本产品不能防水，需避免日晒雨淋，如安装在户外，请用防水箱。
3、良好的散热条件会延长产品的使用寿命，请把产品安装在通风良好的环境。
4、请检查使用的LED电源输出电压电流，是否符合产品要求。
5、出于安全考虑，推荐输入和输出（信号端除外）用0.75-2.5mm² PVC或橡胶线缆，并确保接线牢固，以免电线过热或接触不良触发事故。扁平电源线不适用。
6、通电调试前，应确保所有接线正确，以避免因接线错误而导致灯具损坏。
7、如果发生故障，请勿私自维修；如果有疑问，请联系供应商。
0120 40 60 80 100 120 140 160 180 200 220 240 254
20
40
60
80
100
120
0
110 20 30 40 50
0.1
0.2
0.3
0.4
DALI 调光等级
输出电流
(%)
Push DIM 功能
DALI应用图
备注: 只能使用开路的按压式开关(不带指示灯). 采用同步连线时每个设备和设备之间的线长不超过20米.
Push DIM (Touch DIM)应用图
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
Push DIM Panel(Touch DIM)
LN
861 861 861
12V/24V
861 861 861
12V/24V
861 861 861
12V/24V
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
L
N
DALI 控制器
861 861 861
12V/24V
861 861 861
12V/24V
861 861 861
12V/24V
1.长按Push DIM(Touch DIM)开关8s，进入Push DIM (Touch DIM)模式。
2.短按Push DIM (Touch DIM)开关 (<0.5秒) 进行灯的亮暗控制。
3.长按Push DIM (Touch DIM)开关 (>0.5秒) 进行灯具的亮度调节，光是调亮还是调暗，随着每次按压的开关变化而变换。
4.双击Push DIM (Touch DIM)开关（<0.3秒），连接的所有灯具将达到最亮状态。
5.亮度调节范围为1%-100%。
6.具有断电记忆功能，重新上电将恢复到上一次断电的状态。
100VAC-240VAC
N
L
DALI 信号输入
Input
OUTPUT