EUCHIPS PT-112U User manual

90-240VAC
90-240VAC
Output Voltage
PT-112U
Triac Wall Mount Touch Panel Dimmer
Dimension(mm)
Installation Guide
Wiring Diagram
<1A
-20-60℃
181g
1 channels
L120XW74XH43mm
<3W
<110W(110VAC), <220W(220VAC)
Supply voltage
Net weight
Working temperature
Gross weight 240g
External dimension
Output channel
Packing size
Output Power
Static power
Output current
Trailing-edge dimmingDimming mode
Technical Parameters
Function Description
1/1
User’s manual: 2019-9 www.euchips.com
※The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions, the function of the product shall prevail.Please contact us if you have any questions.
L145XW99XH53mm
Touch this slider by your finger to adjust the brightness.
1. Connect wire according to typical
application. Refer to typical application
2. Gently pry gaps in touch panel with a screwdriver, and then you can slowly remove the
panel, as shown below:
3. Mount the controller on the cassette in the wall after connecting the wire, and then nail
the screw, fix it on the wall, finally you can install the switch pedestal on the wall.
4. Buckle the glass panel to the bottom
box in the right direction
Remarks:
1. Connect the load wire at first, then connect the power wire; Please ensure short circuit
can not occur between connecting wire before you turn on the power.
2. Power supply voltage range is 90-240VAC, more than voltage range maybe will burnout
the controller.
Turn on/off this controller at any state; when the dimmer is turned on, long press
the key for 3 seconds, you can turn on/off buzzer.
Brightness reduce key. Brightness reduces 1 with each short press. With long press,
it could reduce brightness quickly until the darkest.
Brightness increase key. Brightness increase 1 with each short press. With long
press, it could increase brightness quickly until the brightest.
42mm
4mm
74mm
120mm
70mm
8mm
43mm
13mm
AC 90-240V
Triac Dimming
LED Driver Panel
Light
INPUT: Two terminals, L and N, Current 1A
OUTPUT: Two terminals, L and N, Current 1A
Interface Definition
LNLN
INPUT OUTPUT

※本说明书内容如有更新，恕不另行通知。若您使用的产品功能与说明书不一致时，请以产品为准。如有疑问请与我们联系。
Triac壁挂式触控调光器
1/1
用户手册: 2019-9 www.euchips.cn
90-240VAC
90-240VAC
输出电压
1通道输出通道
PT-112U
尺寸(mm)
安装指南
应用接线图
<1A
181g
长 120X 宽 74X 高 43mm
<3W
<110W(110VAC), <220W(220VAC)
输入电压
净重
毛重 240g
尺寸(mm)
输出功率
静态功耗
输入：2 个端子，L 和N，电流 1A
输出：2 个端子，L 和N，电流 1A
输出电流
后沿切相调光方式调光方式
技术参数
功能描述
滑动条: 使用手指滑动进行调光控制, 从上往下亮度降低, 最上面为 100%亮
度, 最暗为5%亮度。
1. 根据特定的应用场合接线。
2. 用螺丝刀轻轻撬开触控板上的缝隙, 然后你就可以慢慢地把它取出来面板，
如下图所示:
3. 连接好电线后，将控制器安装在墙上的暗盒上，然后用钉子固定螺丝固定
在墙上，最后就可以把开关底座安装在墙上了。
4. 将玻璃板按正确的方向扣在底部
的盒子上
备注:
1. 先连接负载线，再连接电源线;接线的时候请确保没有短路，再上电
2. 电源电压范围为90-240VAC，超过电压范围可能会烧坏控制器。
开关键: 单击可开/关面板。开启后灯具恢复到上次关闭时的亮度。
亮度加/减键: 点击按键可进行亮度加减. 可设置 16个等级的亮度, 最
低亮度为 5%, 100%.长按加/减键将快速增加或减小.
按键音:默认为按键音打开.在打开状态下,长按开关键3秒,则可关闭按键音.
42mm
4mm
74mm
120mm
70mm
8mm
43mm
13mm
AC 90-240V
Triac调光驱动 面板灯
接口定义
LNLN
INPUT OUTPUT