EUCHIPS EUP12D-1HMC-0 User manual

DALI Constant Current Dimming Driver
Application
Downlight Panel Light Flood Light
Spotlight Ceiling Light Floor LightDecorative Light
Summary
Product Features
· Single channel output, output current level selectable by DIP S.W.
· Meet DALI Protocol IEC 62386-207 Ed2.0
· Support Touch-DIM function
· Built-in active PFC function
· Dimming effect smooth, no flicker
· Protections: Short circuit, over load
· Suitable for indoor LED lighting application, such as down
light, spot light, and so on
EUP12D-1HMC-0 is a 12W AC/DC constant current mode output LED driver featuring the multiple levels
selectable by DIP switch and complies with DALI standard protocol IEC 62386. EUP12D-1HMC-0 can
be connected to DALI main controller or Touch DIM to a chieve a smooth dimming effect.
EUP12D-1HMC-0 (Product No.:102100263101)
1/2
User’s manual: 2019-8 www.euchips.com
Technical Paramaters
220VAC-240VAC
50/60Hz
80%@230VAC,Full load
≥0.95@230VAC,Full load
Cold start,18A(twidth=14us measured at 50% Ipeak)@230VA C
0.07Amax@230VAC
IP20
-20℃~50℃
-40℃~85℃, 20-90%RH
90℃
EN55015, EN61000-3-2
EN61000-4-2,3,4,5,6,8,11; EN61547
EN61347, GB19510
L-N:1kv
I/P-O/P: 3000VAC/1min/5mA
PC
50,000h@tc:70℃
0.1%-100% Dimming to off
50V Max
±5%
<3%
DALI /Touch DIM
>100,000 times
1
200mA/9-40VDC/8W 250mA/9-40VDC/10W
300mA/9-40VDC/12W 350mA/9-34VDC/11.9W
<10%@230VAC, Full load
EUP12D-1HMC-0
Surge
Withstand Voltage
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC62386-207 Ed2.0DALI Standard
Safety Standards
EMC Eission
EMC Immunity
tc
Lifetime
Material
Dimming Range
IP Rating
Working Temp.
Storage Temp., Humidity
Dimming Type
Switch Cycle
Warranty Condition 5 Years
No load output voltage
Efficiency
AC Current(max)
Standby power <0.5W
Inrush Current(max)
THD(full load)
Current(mA)/Voltage (VDC)
Power(W)
Ripple Current
Channel
Current Tolerance
Voltage
Frequency Range(Hz)
Power Factor
Short Circuit
Over Load
Close output，recovers automatically after fault removed
When the output voltage is exceeded, the output current decreases and, recovers automatically when the load is reduced.
Safety
&
EMC
Others
Function
Model
Output
Input
Protection
Current Selection Table
Remark: Function default setting is: 200mA
(@switch are all OFF state)
200mA 250mA 300mA
9-40V 9-40V
350mA
9-34V9-40V
ON OFF
Net weight: 125g±5%/PCS; 50PCS/Carton; 6.65kg±5%/Carton; Carton Size: 319*254*136mm(L*W*H)
Packing(weight)
150*43*29mm(L*W*H)
Dimension

DALI Constant Current Dimming Driver
2/2
User’s manual: 2019-8 www.euchips.com
150.0
29
43
32.5 25.0
140.5
90.5
4.0
Dimension(mm) DALI Wiring
Push DIM(Touch DIM) Diagram
Push DIM Function
1. Press the Push DIM (Touch DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.
2. Short press the Push DIM (Touch DIM) switch (<0.5s) to control the lamp on or off.
3. Long press the Push DIM (Touch DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Push DIM (Touch DIM) switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing Push DIM (Touch DIM) switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
DALI Diagram
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
L
N
DALI Controller
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
Push DIM Panel(Touch DIM)
LN
※The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions, the function of the product shall prevail.Please contact us if you have any
questions .
DA 1
DALI
DA 2 LED+
LED -
INPUT
DALI Signal Input
DALI Master
L
N
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75- 1.5mm²is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
1 2 3
ON
LED-
LED+
OUTPUT
3
2
1
ON
N
L
0.45N.m
Torque
Dimming Curve Derating Curve
Ambient Temperature(℃)
-20
0
20
40
60
80
100
120
Load(%)
-10 0 10 20 30 40 50 60
01 20 40 60 80 100 120 140 160 180 200 220 240 254
20
40
60
80
100
120
0
110 20 30 40 50
0.1
0.2
0.3
0.4
DALI Dimming Level
Output Current(%)
Max. quantity of drivers per miniature circuit breaker
Max. distance between independent use LED driver and LED modules
MCB type
Installation
B16
36 45
1.5mm²1.5mm²
C16
Quantity
Distance 5m/16ft
0.5mm²/AWG20 0.5mm²/AWG20 1mm²/AWG17
2.5mm²/AWG13
10m/32ft 20m/65ft 30m/98ft
Cable Section

220VAC-240VAC
50/60Hz
80%@230VAC, 满载
≥0.95@230VAC, 满载
<0.5W
冷启动,18A(在50%Ipeak下测twidth=14us)@230VACC
0.07Amax@230VAC
150*43*29mm（长*宽*高）
IP20
-20℃~50℃
-40℃~85℃, 20-90%RH
90℃
EN50515, EN61000-3-2
EN61000-4-2, 3, 4, 5, 6, 8, 11; EN61547
EN61347, GB19510
L-N:1kv
I/P-O/P: 3000VAC/1min/5mA
IEC 62386-101: 2014, IEC 62386-102: 2014; IEC62386-207 Ed2.0
PC
50,000小时@tc:70℃
0.1%-100% 变暗直至关闭
50V Max
±5%
<3%
>100,000次
1
<10%@230VAC, 满载
EUP12D-1HMC-0
浪涌
耐压标准
DALI标准
安全标准
电磁兼容
EMC抗扰度
tc
寿命
材质
调光范围
尺寸
包装尺寸(重量)
防水等级
工作温度
储存温度、湿度
调光方式
开关周期
5年质保
空载输出电压
效率
待机功耗
电流
浪涌电流
THD
电流/电压/功率
波纹电流
通道
电流精度
电压
频率
功率因素
短路
过载
关闭输出，排除故障后自恢复
打嗝，移除故障后自恢复
安全
&
电磁
兼容
其它
功能
型号
输出
输入
保护
应用
筒灯 面板灯 投光灯
射灯 吸顶灯 落地灯装饰灯
概述
产品特点
· 单通道恒流输出，多级电流可选
· 遵循DALI协议标准 IEC 62386-207 Ed2.0
· 支持Touch-DIM功能
· 高电压输入：220VAC ~ 240VAC
· 内建主动式PFC功能
· 短路保护，过载保护
· 适用于LED室内灯具,比如筒灯，面板灯等
EUP12D-1HMC-0 (产品代码:102100263101)
1/2
用户手册: 2019-8 www.euchips.cn
电流选择表
备注：出厂默认设置电流为200mA(1,2在OFF状态)
技术参数
净重: 125g±5%/PCS; 50PCS/Carton; 6.65kg±5%/箱; 外箱尺寸: 319*254*136cm(长*宽*高)
EUP12D-1HMC-0 是一款可以提供200/250/300/350mA 4档电流的LED驱动器。输出电流
可以通过DIP拨码开关简易设置，用DALI 主控/Touch DIM开关调光，曲线平滑、无闪烁。
DALI/Touch DIM
200mA/9-40VDC/8W
300mA/9-40VDC/12W 350mA/9-34VDC/11.9W
250mA/9-40VDC/10W
200mA 250mA 300mA
9-40V 9-40V
350mA
9-34V9-40V
ON OFF
DALI 恒流调光驱动器

DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
L
N
DALI 控制器
DALI Driver 1
DA
DA LED+
LED-
L
N
DALI Driver 1
DA
DA LED+
LED-
L
N
Push DIM Panel(Touch DIM)
LN
2/2
用户手册: 2019-8 www.euchips.cn
150.0
28.5
42.5
32.5 25.0
140.5
90.5
4.0
尺寸(mm)
DA 1
DALI
DA 2 LED+
LED -
INPUT
DALI 信号输入
DALI 主控
L
N
接线图
※ 本说明书内容如有更新，恕不另行通知。若您使用的产品功能与说明书不一致时，请以产品为准。如有疑问请与我们联系。
注意事项:
1、本产品请由具有专业资格的人员进行调试安装。
2、本产品不能防水，需避免日晒雨淋，如安装在户外，请用防水箱。
3、良好的散热条件会延长产品的使用寿命，请把产品安装在通风良好的环境。
4、请检查使用的LED电源输出电压电流，是否符合产品要求。
5、出于安全考虑，推荐输入和输出（信号端除外）用0.75-1.5mm² PVC或橡胶线缆，并确保接线牢固，以免电线过热或接触不良触发事故。扁平电源线不适用。
6、通电调试前，应确保所有接线正确，以避免因接线错误而导致灯具损坏。
7、如果发生故障，请勿私自维修；如果有疑问，请联系供应商。
Push DIM 功能
DALI应用图
备注: 只能使用开路的按压式开关(不带指示灯). 采用同步连线时每个设备和设备之间的线长不超过20米.
Push DIM (Touch DIM)应用图
1.长按Push DIM(Touch DIM)开关8s，进入Push DIM (Touch DIM)模式。
2.短按Push DIM (Touch DIM)开关 (<0.5秒) 进行灯的亮暗控制。
3.长按Push DIM (Touch DIM)开关 (>0.5秒) 进行灯具的亮度调节，光是调亮还是调暗，随着每次按压的开关变化而变换。
4.双击Push DIM (Touch DIM)开关（<0.3秒），连接的所有灯具将达到最亮状态。
5.亮度调节范围为1%-100%。
6.具有断电记忆功能，重新上电将恢复到上一次断电的状态。
DALI 恒流调光驱动器
1 2 3
ON
LED-
LED+
OUTPUT
3
2
1
ON
N
L
0.45N.m
Torque
调光曲线 降额曲线
环境温度(℃)
负载(%)
-20
0
20
40
60
80
100
120
-10 0 10 20 30 40 50 60
DALI 调光等级
输出电流(%)
01 20 40 60 80 100 120 140 160 180 200 220 240 254
20
40
60
80
100
120
0
110 20 30 40 50
0.1
0.2
0.3
0.4
断路器的带载说明
驱动与灯具的安装距离
断路器类型
安装线径
B16
36 45
1.5mm²1.5mm²
C16
最大允许数量
距离 5m/16ft
0.5mm²/AWG20 0.5mm²/AWG20 1mm²/AWG17 2.5mm²/AWG13
10m/32ft 20m/65ft 30m/98ft
线径