Cable Entry
• Supply 24VDC +/- 5% 10W or use the Power over Ethernet (PoE module
needed*). Use a suitible Cat5e data cable to connect comms.
• Run power and data into your device using waterproof cable glands, (Max
16mm Diameter) or internally threaded conduit (Max 20mm diameter).
• Holes can be made by drilling through one of the marked locations on the box.
• For an IP67 application use rated glands or enter through the underside
with suitably sealed conduit. Entry through the back is possible but if ingress
protection is needed then the entry hole must be suitably sealed.
VIEW A-A
SCALE 1 : 1
SECTION B-B
SCALE 1.25 : 1
A
B
B
1
123456
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A0
THIS DRAWING IS THE PROPERTY OF AND MAY EMBODY PROPRIET ARYIN FORMATION
OWNED BY AVONWOOD DEV ELOPMENTS LTD. IT IS P ROVIDED UNDER A CONF IDENTIAL
RELATIONSHIP FOR A SPECIFIC PUR POSE. THE RECIPIENT AGREE S TOU SE IT ONLY FOR
SUCH PURPOSE.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
60.00
155.00
155.00
DRILL POINT DRILL POINT
DRILL POINT
DRILL POINT
AMPS
THREAD DEPTH
POWER INDICATOR
READ INDICATOR
POWER INDICATOR
GOOD BATTERY
BAD BATTERY
14.0014.00
28.00
VIEW A-A
SCALE 1 : 1
SECTION B-B
SCALE 1.25 : 1
A
B
B
1
123456
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A0
THIS DRAWING IS THE PROPERTY OF AND MAY EMBODY PROPRIET ARYIN FORMATION
OWNED BY AVONWOOD DEV ELOPMENTS LTD. IT IS P ROVIDED UNDER A CONF IDENTIAL
RELATIONSHIP FOR A SPECIFIC PUR POSE. THE RECIPIENT AGREE S TOU SE IT ONLY FOR
SUCH PURPOSE.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
60.00
155.00
155.00
DRILL POINT DRILL POINT
DRILL POINT
DRILL POINT
AMPS
THREAD DEPTH
POWER INDICATOR
READ INDICATOR
POWER INDICATOR
GOOD BATTERY
BAD BATTERY
14.0014.00
28.00
VIEW A-A
SCALE 1 : 1
SECTION B-B
SCALE 1.25 : 1
A
B
B
1
123456
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A0
THIS DRAWING IS THE PROPERTY OF AND MAY EMBODY PROPRIET ARYIN FORMATION
OWNED BY AVONWOOD DEV ELOPMENTS LTD. IT IS P ROVIDED UNDER A CONF IDENTIAL
RELATIONSHIP FOR A SPECIFIC PUR POSE. THE RECIPIENT AGREE S TOU SE IT ONLY FOR
SUCH PURPOSE.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
60.00
155.00
155.00
DRILL POINT DRILL POINT
DRILL POINT
DRILL POINT
AMPS
THREAD DEPTH
POWER INDICATOR
READ INDICATOR
POWER INDICATOR
GOOD BATTERY
BAD BATTERY
14.0014.00
28.00
Drill marks
VIEW A-A
SCALE 1 : 1
SECTION B-B
SCALE 1.25 : 1
A
B
B
1
123456
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A0
THIS DRAWING IS THE PROPER TY OF AND MAY EMBODY P ROPRIETARY INFORMATIO N
OWNED BY A VONWOOD DEVELOP MENTS LTD. IT IS PR OVIDED UNDER A CONFI DENTIAL
RELATIONSHIP FOR A SPECIFIC PURPOSE. THE RECIPIENT AGREES TO USE IT ONLY FOR
SUCH PUR POSE.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
60.00
155.00
155.00
DRILL POINT DRILL POINT
DRILL POINT
DRILL POINT
AMPS
THREAD DEPTH
POWER INDICATOR
READ INDICATOR
POWER INDICATOR
GOOD BATTERY
BAD BATTERY
14.0014.00
28.00
NOTE:
Please make a note of the serial
number located on the back of
the device for ease of set up. You
will need this number in order
to set up and connect to the
network.
DETAIL A
SCALE 1 : 1
SECTION B-B
SCALE 2:1
SECTION C-C
SCALE 2:1
A
B B
C C
1
123 4 5 6
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A1
THIS DRAWING IS THE PROPERTY OF AND MAY EMBODY PROPRIETARY INFORMATION
OWNED BY AVONWOOD DEVELOPMENTS LTD. IT IS PROVIDED UNDER A CONFIDENTIAL
RELATIONSHIP FOR A SPECIFIC PURPOSE. THE RECIPIENT AGREES TO USE IT ONLY FOR
SUCH PURPOSE.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
30.00
38.00
3.00 7.40
12.00
1.60
5.40
3.00
1.60
10.00
M5 X 0.8mm PITCH
M5 INT TOOTH SHAKEPROOF
M5 PLAIN
FIXTURE
0.00 200mm
38.00
30.00
• Alternatively drill holes through the back where shown above.
• To use RAM Mount xtures, attach a 1.5”RAM Mount base plate.
• Back x with the four AMPS holes to suit your application.
VIEW A-A
SCALE 1 : 1
SECTION B-B
SCALE 1.25 : 1
A
B
B
1
123456
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A0
THIS DRAWING IS THE PROPERTY OF AND MA YEM BODY PROPRIETARY INFORMATION
OWNED BY AVO NWOOD DEVELOPMEN TS LTD. IT IS PROVIDED UN DER A CONFIDENTIAL
RELATIONSH IPF OR A SPECIFIC PURPOSE. THE REC IPIENT AGREES TO USE IT ONLY FOR
SUCH PURPOS E.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
60.00
155.00
155.00
DRILL POINT DRILL POINT
DRILL POINT
DRILL POINT
AMPS
THREAD DEPTH
POWER INDICATOR
READ INDICATOR
POWER INDICATOR
GOOD BATTERY
BAD BATTERY
14.0014.00
28.00
VIEW A-A
SCALE 1 : 1
SECTION B-B
SCALE 1.25 : 1
A
B
B
1
123456
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A0
THIS DRAWING IS THE PROPERTY OF AND MA YEM BODY PROPRIETARY INFORMATION
OWNED BY AVO NWOOD DEVELOPMEN TS LTD. IT IS PROVIDED UN DER A CONFIDENTIAL
RELATIONSHI PF OR A SPECIFIC PURPOSE. THE REC IPIENT AGREES TO USE IT ONLY FOR
SUCH PURPOS E.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
60.00
155.00
155.00
DRILL POINT DRILL POINT
DRILL POINT
DRILL POINT
AMPS
THREAD DEPTH
POWER INDICATOR
READ INDICATOR
POWER INDICATOR
GOOD BATTERY
BAD BATTERY
14.0014.00
28.00
See back
cover for
1:1 AMPS
template.
VIEW A-A
SCALE 1 : 1
SECTION B-B
SCALE 1.25 : 1
A
B
B
1
123456
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A0
THIS DRAWING IS THE PROPERTY OF AND MA YEM BODY PROPRIETARY INFORMATION
OWNED BY AVO NWOOD DEVELOPMEN TS LTD. IT IS PROVIDED UN DER A CONFIDENTIAL
RELATIONSHI PF OR A SPECIFIC PURPOSE. THE RE CIPIENT AGREES TO USE IT ONLY FOR
SUCH PURPOS E.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
60.00
155.00
155.00
DRILL POINT DRILL POINT
DRILL POINT
DRILL POINT
AMPS
THREAD DEPTH
POWER INDICATOR
READ INDICATOR
POWER INDICATOR
GOOD BATTERY
BAD BATTERY
14.0014.00
28.00
DRILL POINT DRILL POINT
DRILL POINTDRILL POINT
THREAD
DEPTH
AMPS
DETAIL A
SCALE 1 : 1
SECTION B-B
SCALE 2:1
SECTION C-C
SCALE 2:1
A
B B
C C
1
123 4 5 6
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A1
THIS DRAWING IS THE PROPERTY OF AND MAY EMBODY PROPRIETARY INFORMATION
OWNED BY AVONWOOD DEVELOPMENTS LTD. IT IS PROVIDED UNDER A CONFIDENTIAL
RELATIONSHIP FOR A SPECIFIC PURPOSE. THE RECIPIENT AGREES TO USE IT ONLY FOR
SUCH PURPOSE.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
30.00
38.00
3.00 7.40
12.00
1.60
5.40
3.00
1.60
10.00
M5 X 0.8mm PITCH
M5 INT TOOTH SHAKEPROOF
M5 PLAIN
DETAIL A
SCALE 1 : 1
SECTION B-B
SCALE 2:1
SECTION C-C
SCALE 2:1
A
B B
C C
1
123 4 5 6
A
B
C
D
E
F
REV: DATE: CHANGE:
STATUS:
CUSTOMER:
SCALE @
DRAWN BY:
REV:
DRAWING NO:
TITLE:
UNCONTROLLED
SHEET
A1
THIS DRAWING IS THE PROPERTY OF AND MAY EMBODY PROPRIETARY INFORMATION
OWNED BY AVONWOOD DEVELOPMENTS LTD. IT IS PROVIDED UNDER A CONFIDENTIAL
RELATIONSHIP FOR A SPECIFIC PURPOSE. THE RECIPIENT AGREES TO USE IT ONLY FOR
SUCH PURPOSE.
AS INDICATED IN ISO 2768-1
TOLERANCE CLASS
LINEAR = f
ANGULAR = f
BROKEN EDGES = f
1 / 1
UNLESS OTHERWISE STATED
30.00
38.00
3.00 7.40
12.00
1.60
5.40
3.00
1.60
10.00
M5 X 0.8mm PITCH
M5 INT TOOTH SHAKEPROOF
M5 PLAIN
FIXTURE
0.00 200mm
THREAD LOCK
M5 PLAIN
M5 INT TOOTH SHAKEPROOF
M5 X 0.8mm PITCH
THREAD LOCK
Introduction
There are two models of the Plus Reader. The Tag Reader model can be used to
provide restricted or controlled access through doors, turnstiles and gates. The Tag
Tester model enables users to quickly and easily check the status of their tags.
Simple LED indication panels on both models highlight whether the reader has
power, the tag can be read, and the tag battery level status.
Both readers are compatible with the Eureka tag range including :
ZoneSafe VibraTag, ZoneSafe High Capacity Tag and ZoneSafe’s standard tag range.
Fixing
*sold seperately
See back cover for 1:1 Drill Point template.
Ram Mount
Ball Fixing
