EUROPRO SANDBLASTPRO 30L User manual

EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET - Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510
SANDBLASTPRO 30L
Réf. 30860
User manual
Edition of 14/06/2021
More information on www.euromair.com

User manual - SandblastPro 30L 202106-528-ENGP2
You just acquired one of our
machines and all the team
of Europe Projection thanks
you for the condence
you have granted us.
Manufacturer of professional
equipments for paint and
llers, we have put our
know-how for 25 years
at the service of the
users of our machines.
Our technical & commercial
team is at your disposal
for any further information
you may need about the
machine you just acquired.
EUROPE PROJECTION
228, avenue Olivier Perroy
13790 ROUSSET
Tél : [phone]
[e-mail]
SUMMARY
1. USER MANUAL............................................................. p. 3
1.1. Importance of the manual .........................................p. 3
1.2. Receivers of the manual............................................p. 3
2. WARNING .................................................................... p. 4
2.1. Safety .....................................................................p. 4
2.2. End-of-life of the product ..........................................p. 6
3. YOUR MACHINE ........................................................... p. 7
3.1. Description..............................................................p. 7
3.2. Technical characteristics ...........................................p. 7
3.3. Identication of the components ................................p. 8
4. USE OF THE MACHINE ................................................. p. 9
4.1. Prerequisites............................................................p. 9
4.2. Starting up ..............................................................p. 9
5. FAILURES AND REMEDIES............................................ p.10
6. MAINTENANCE............................................................. p.11
7. DECLARATION OF CONFORMITY ................................... p.13
8. WARRANTY CONDITIONS.............................................. p.15

202106-528-ENG User manual - SandblastPro 30L P3
1. USER MANUAL
1.1. IMPORTANCE OF THE MANUAL
This manual is a key part for the use of your machine. It summarizes the procedures of starting-up, cleaning
and maintenance of the device and also the safety instructions you need to observe.
Read carefully all the working and safety instructions and the warnings included in this manual before
starting your machine.
Most of the accidents are caused by the non-compliance of the safety standards and rules.
This manual must be kept near the machine, within reach of the user and held in good condition until the
nal destruction of the machine.
In case of loss or deterioration of the manual, you can ask the machine manufacturer mentioned on page
4 for a copy at any moment.
1.2. RECEIVERS OF THE MANUAL
This manual is intended to any staff which will manipulate the machine :
- people in charge of the transport of the machine
- people in charge of the use of the machine
- people in charge of the cleaning and maintenance of the machine
- people in charge of the nal destruction of the machine

User manual - SandblastPro 30L 202106-528-ENGP4
2. WARNING
2.1. SAFETY
Using the machine in an incorrect way or in non-compliance of the safety instructions indicated in
this manual can cause death or serious injuries.
Read carefully all the working and safety instructions and the warnings contained in this manual
before starting your machine.
• Respect all the safety standards before running the equipment.
• Use the equipment only for the applications specied in the manual.
• Always remain alert when using the equipment.
• Transport the machine using the handles or the appropriate grips.
• During the breaks, disconnect electrically the machine.
• Run the equipment to its nominal voltage.
• Let at least 50 cm of free space between the equipment and any obstacle so that the air ow
is not blocked.
• Know how to quickly stop the equipment in case of necessity.
• Never use the equipment while it is running abnormally or it is defective.
• Do not direct a water jet or ammable liquid on the machine.
• Never direct an air jet or product jet on a person or an animal.
• Do not touch warm surfaces of the equipment.
• Never touch moving parts.
• Do not insert any object or the hands inside the protection grids to avoid any accident or
damage to the machine.
• For any outside job, only use appropriate extension cords.
• Always wear adequate body protections (glasses, gloves, overall and mask) and pay attention
to long hair.
• Maintain the equipment carefully and clean it properly after every use.
• Disconnect the equipment before any intervention.
• Avoid absolutely to unscrew any connection while the machine is under pressure.
• Check the damaged parts.
• Do not clean the plastic parts with solvant.
• In case of damage of the electric cable or the plug, do not run the machine and contact a
licensed After-Sale Service to put genuine parts instead of the defective ones.
• In case of needed After-Sale Service, always specify the machine model and its serial number.
• For any replacement of parts, only use genuine parts.
• Do not modify the machine.
• Do not cut or dismantle the protection grids.
• Do not open the electric box.

202106-528-ENG User manual - SandblastPro 30L P5
IN CASE OF NECESSITY, WE SAVE OURSELVES THE RIGHT TO MAKE ANY USEFUL
MODIFICATION WITHOUT ADVANCED NOTICE.
2. WARNING (continued)
2.1. SAFETY (continued)
WORKSPACE
• Maintain the workspace clean and clear.
• Ambient operating temperature must be from 5°C and 35°C.
• Do not use the equipment in a potentially explosive area.
• Do not place any potentially inammable objects in close proximity to the machine.
• Take away every not qualied person from the working area of the machine, as well as children and
animals.
• In case of installation of the machine on scaffolding or a plan above ground level, attach the machine
to avoid any fall while operating.
• Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.
HOSES
• Always use hoses and connections adapted to the used product (genuine parts), do not try to x it.
• Do not walk on the hoses, do not bend them.
• Do not use the hoses to pull the machine.
STORAGE
• Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.

User manual - SandblastPro 30L 202106-528-ENGP6
2. WARNING (continued)
2.2. END OF LIFE OF THE PRODUCT
At its end-of-life, the machine must not be eliminated with the other household waste. The
uncontrolled elimination of waste can harm the environment or human health. Individuals are
invited to contact the distributor which sold them the product or to inquire with their city hall
to know where and how to get rid of the product so it can be recycled while respecting the
environment.
Under the regulation of Waste of Electrical and Electronic Equipments (WEEE), we undertake to
process the used EEEs according to the following provisions: applicable only to products on the
market since 08/13/05, under the brands EUROPE PROJECTION or VOLUMAIR, products of other
brands sold by our company (upon presentation of the corresponding invoices), products that
operate using electrical energy (for example, thermal washers or compressors do not fall into this
category).
Treatment modality
WEEE returns collected by our clients/distributors at their own expense to our collection points in
Antony (92) or Rousset sur Arc (13). Upon receipt, the products are sorted by our employees and
directed to the most appropriate processing channels.
For any further information, please contact our hotline [phone] or [e-mail].

202106-528-ENG User manual - SandblastPro 30L P7
3. YOUR MACHINE
3.1. DESCRIPTION
Compact and handy, this versatile sandblaster is designed for small-scale stripping jobs by sandblasting or
microblasting:
• refurbishment of old furniture
• small facade renovation jobs
• cleaning of soft stones
• preparation of metallic surfaces (railings, portals, etc.)
• restoration of former vehicles
• cleaning of wall grafti
• glass engraving
The machine is also ideal for hydroblasting (with optional kit).
3.2. TECHNICAL CHARACTERISTICS
Max. working pressure 6 bar
Air consumption 450 L/min
Tank capacity 30 L
Dimensions (L x w x h) 51 x 44 x 92 cm
Weight 32 kg
Delivered with
- a hose of 8 m
- a sanding-gun
- a Ø3 mm Venturi tungsten nozzle
- a lling bowl
- a sieve
- a pair of gloves
- a face protection screen
- a FFP2 ap respirator mask
Do not use water or moistened cotton wadding at the risk of clogging the machine.

D
A
B
C
G
F
E
User manual - SandblastPro 30L 202106-528-ENGP8
3. YOUR MACHINE (continued)
3.3. IDENTIFICATION OF THE COMPONENTS
AGun
BNozzle
CFilling funnel (with integrated strainer)
DAir inlet connection
EAir pressure adjustment knob
FManometer
GAbrasive ow adjustment knob

202106-528-ENG User manual - SandblastPro 30L P9
4. USE OF THE MACHINE
4.1. PREREQUISITES
• It is advisable to cover the oor where the blasting operation is to be carried out so that the work area
can be cleaned more easily. The residues from the blasting operation (paint, varnish, metal, etc.) can
be harmful to the environment and the user.
• It is imperative to use clean and dry air when using the sandblaster to avoid the risk of clogging.
Depending on the compressor used, an air dryer should be used in addition.
• Always use the personal protective equipment supplied with the machine (gloves, visor, mask) in order
to avoid risks for the operator.
4.2. STARTING UP
1. Connect the air hose to the coupling (D) and start the compressor coupled to the sandblaster.
2. Insert the funnel (C) with the sieve and pour the abrasive.
3. When all the abrasive has owed into the tank, remove the lling funnel and close the cap.
4. Fit the appropriate nozzle (B) to the gun (A).
5. To adjust the air ow, pull the knob (E) upwards. Rotate to adjust and then press the knob back in to
conrm the setting.
6. To adjust the abrasive ow rate, turn the knob (G). Counterclockwise to increase the ow, clockwise
to decrease the ow.
7. Press the gun trigger to start working.

User manual - SandblastPro 30L 202106-528-ENGP10
5. FAILURES AND REMEDIES
Failure To be checked Remedy
Air does not come out of
the nozzle.
• Compressor not connected or
switched off.
• Connect the compressor to the
sandblaster and turn it on.
• Nozzle clogged. • Remove the gun nozzle and blow it
out to remove the blockage.
• Clogged product hose. • Remove the product hose and clean
it.
• Abrasive outlet blocked. • Turn knob (G) to increase ow rate.
• Clean the tank outlet lines.
• The three-way valve in the regulation
box does not work. • Repair or replace valve.
Abrasive does not come
out of the gun.
• No abrasive in the tank. • Fill the tank with abrasive.
• Abrasive outlet blocked. • Turn knob (G) to increase ow rate.
• Clean the tank outlet pipes.
• Excessive particle size of the abrasive
used.
• Empty the tank and ll it with the
correct abrasive grain size.
• Blow out the hoses to remove any
remaining abrasive.
• Abrasive outlet knob closed. • Turn the knob (G) to increase the ow
rate.
Non-uniform ow of
abrasive.
• Wet abrasive or abrasive with foreign
particles.
• Empty the tank and ll with dry,
ltered abrasive.
• Excessive particle size of abrasive
used.
• Empty the tank and ll it with the
correct abrasive grain size.
• Blow out the hoses to remove any
remaining abrasive.
• Abrasive ow knob too open. • Turn the knob (G) to regulate the ow.
The result of the
application is not
satisfying.
• Nozzle not suitable for the application. • Change the nozzle.
• Lack of seal. • Change hoses.
• Inadequate working pressure. • Turn the adjustment knob (E) until the
desired result is achieved.
• Inadequate abrasive for the job.
• Contact the abrasive supplier to use
the most suitable product for the
application.
Before loosening the hose, make sure it is no longer under pressure.

202106-528-ENG User manual - SandblastPro 30L P11
5. FAILURES AND REMEDIES (continued)
Failure To be checked Remedy
Air escaping through
safety valve.
• Excessive air pressure from the
compressor feeding the sandblaster.
• Adjust the compressor air outlet
pressure to a maximum of 6 kg/cm².
Insufcient air outlet at
the nozzle.
• Clogged purifying lter. • Clean the purifying lter.
• Clogged nozzle on the hose side.
• Disconnect the hose from the
sandblaster and blow out the nozzle
to unclog it.
Lack of seal at lids.
• Presence of particles or foreign bodies
that prevent the covers from closing
properly.
• Clean the contact surfaces of the
covers.
• Deteriorated or damaged seals. • Change the seals.
Gun trigger seized. • Lack of lubrication. • Lubricate and clean the gun trigger
regularly.
• Lack of cleaning.
6. MAINTENANCE
AFTER EVERY USE
• Remove the lter regulator and clean it. Also clean the lter tank.
REGULARLY OR IF THE MACHINE IS NOT USED FOR A LONG PERIOD
• Empty all abrasive from the tank and hoses.
• Clean the tank and blow out the hoses to remove all abrasive residues.
If the problem persists or if in doubt on the good running of the machine, do not try to repair
it by yourself or to dismantle it.
Contact an authorized After-Sale Service or our hotline : [phone].

User manual - SandblastPro 30L 202106-528-ENGP12

202106-528-ENG User manual - SandblastPro 30L P13
7. DECLARATION OF CONFORMITY
THE MANUFACTURER : EUROPE PROJECTION
228, avenue Olivier Perroy
13790 ROUSSET
DECLARES THAT THE EQUIPMENT DESIGNATED BELOW :
Trademark : EUROPRO
Type : Sandblaster
Model : SANDBLASTPRO 30L
COMPLIES WITH THE DIRECTIVES:
• Machines 2006/42/CE
• Noise emissions 2005/88/CE
AND WITH THE STANDARD:
• NF EN 13445
ROUSSET, JANUARY 20th 2021
Patrick BOREL
President
EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET
Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510

User manual - SandblastPro 30L 202106-528-ENGP14

202106-528-ENG User manual - SandblastPro 30L P15
8. WARRANTY CONDITIONS
Each product is delivered inspected and tested.
We exclude any warranty for visible defects for which the customer did not claim within 48 hours.
The equipments sold are covered by the warranty during the period dened by the manufacturer from
the date of purchase, the date on the original proof of purchase being authentic and under the conditions
dened by the manufacturer.
This warranty covers any equipment against any manufacturing or material defect of for normal use and
service. Insofar as the customer is presumed to be a professional of the same specialty, the guarantee
covers only the lack of realization of the equipment rendering it unt for its use not likely to be detected by
a professional buyer.
The defects or deteriorations caused by natural wear, external accident or a modication, use, storage or
treatment of equipments not planned by the manufacturer, nor specied by ourselves, are excluded from
any warranty.
Are expressly excluded from the warranty the defects coming from: a bad use, the application of abrasive
or corrosive products, an inappropriate installation, the negligence, an insufcient maintenance or cleaning
chemical, electrochemical or electric inuences, any change in the normal process of use.
The following wearing parts are not covered by the warranty: rotors, stators, driving shafts, connecting rods,
seals, cleaning balls, spray guns, lance, nozzle, hose, needle kits, cylinders, piston rods, prime/spray valve
assy, seal kits, membranes, suction and delivery valves, carding machine vanes, lters, oils.
The warranty also excludes the equipments: on which the serial number was erased or made illegible, on
which unauthorized people made attempts of repair which were totally or partially dismantled.
Defective equipment will be removed by us. Any shipment of equipment by the customer will be at its own
expense. The guarantee will be subject to the presentation of the purchase invoice. We will then be able to
perform an equipment analysis to determine if the defect is covered by the warranty.
If the defective equipment is covered by the warranty, it will be repaired or replaced free of charge. Repaired
equipment (under warranty) will be delivered to the customer free of charge.
If the defective equipment is not covered by the warranty, we will issue a quote for the repair that we will
submit to the customer’s agreement. The costs of removal and shipping of equipment not covered by the
warranty will be charged to the customer, whether or not the latter accepts the repair estimate.
Except as otherwise required by law, this warranty is exclusive of all other warranties, including the statutory
warranty of hidden defects.
In case of intervention of our services on a breakdown caused by the customer or an outage excluded in the
conditions referred to above, the costs of repair and transport will be billed to the customer.
We exclude all liability for indirect damages suffered by the customer, such as, but not limited to, loss of
income, turnover, loss of prots, loss of image, of any kind whatever.
In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment.
Any action of the customer against us relating to the guarantee of the equipments will be prescribed within
the period of 1 year as from the day of the discovery of the defect. It is up to the customer to prove the day
of this discovery.
Our equipments are covered by a warranty (parts and labour) of 12 months following the purchase.
The duration of this warranty can be extended by 6 months by completing the warranty extension
form within 4 weeks after purchasing on our website www.euromair.com (section Warranty).

EUROPE PROJECTION - 228, avenue Olivier Perroy 13790 ROUSSET - Tél : [phone] – Fax : [phone]
SAS au capital de 400 000 € - RCS Aix-en-Provence B 394 961 510 - NAF 2892 Z - Intracom : FR 54 394 961 510
User manual - SandblastPro 30L 202106-528-ENGP16
More information on www.euromair.com