Evenflo Loft 245404225 User manual

2
WARNING
ADVERTENCIA
FAILURE TO FOLLOW THESE WARNINGS AND THE
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
• ALWAYS provide the
supervision necessary for the
continued safety of your child.
NEVER leave child unattended.
• BEFORE USE, remove and
dispose of all plastic bags and
packaging materials and keep
them out of reach of children.
• ALWAYS FOLLOW the
instructions in the owner’s
manual to set up the bassinet.
MAKE SURE bassinet is locked
and in the open position before
placing child in the bassinet.
• FALL HAZARD - To help prevent
falls, do not use this product
when the infant begins to push
up on hands and knees, roll over
or has reached 20 lbs. (9kg),
whichever comes rst.
• SUFFOCATION HAZARD -
INFANTS HAVE SUFFOCATED:
• In gaps between extra padding
and side of the bassinet, and
• On soft bedding
Use only the pad provided by
the manufacturer. NEVER add
a pillow, comforter, or another
mattress for padding.
• TO REDUCE THE RISK OF
SIDS, pediatricians recommend
healthy infants be placed on
their back to sleep, unless
otherwise advised by your
physician.
• IF A SHEET IS USED with the
pad, use only the one provided
by Eveno.
• STRINGS CAN CAUSE STRAN-
GULATION! Never place items
with a string around a child’s
neck, such as hood strings or
pacier cords.
Never suspend strings over the
bassinet or attach strings to toys.
• DO NOT place the bassinet near
a window where cords from
blinds or drapes can strangle a
child.
• USE bassinet with only one child
at a time.
• ALWAYS keep objects out of
child’s reach.
• DO NOT use accessories, spare
parts, or any component not
supplied or approved by Eveno
as they may make the bassinet
unsafe.
• KEEP bassinet away from stoves,
heaters, replaces and other
hazards which can cause injury
to your child.
• DO NOT move or carry the bas-
sinet with the child in it. Child
could be injured.
• DO NOT allow children to play
around or under the bassinet.
• NEVER use this product if there
are any loose or missing fasten-
ers, loose joints, broken parts,
or torn mesh/fabric. Check
periodically during use. Contact
Eveno for replacement parts
and instruction if needed. Never
substitute parts.

3
Parts
Please check that you have all the parts shown below before
assembling product.
If you are missing any parts, please contact CNP.
Tools required : Phillips screwdriver
Leg Tubes
Bassinet Frame
Bluetooth Music Module
Fitted Sheet Mattress Pad
2X
Model # 24504225

4
1Before assembly be sure to place
bassinet on the attened carton to
prevent damage to oor surface.
Lift up on both ends of the
bassinet until they CLICK into the
open position.
Press down on both ends of the
bassinet to make sure that it is
securely opened.
To Set Up Bassinet
CLICK!
2Place the bassinet frame on the
ground with the legs facing up.
Attach leg tubes to the frame legs
until they “click” in place.
NOTE: Make sure button on frame
leg snaps into holes on leg tube for
proper attachment.
Repeat for other other side.
CLICK!
CLICK!
Rivet

5
1Cover mattress pad with tted
sheet (provided). Make sure the 4
Velcro® patches are on the bottom
of the mattress pad are NOT
covered by the tted sheet.
Inserting Mattress Pad
2Place mattress pad into bassinet.
Make sure all (4) Velcro® tabs on
bottom of mattress pad fasten to
the 4 Velcro patches on bottom of
bassinet.
PREVENT possible strangulation or
entanglement. Never use bassinet sheet unless
it ts securely on the bassinet mattress pad.
WARNING
ADVERTENCIA
3Make sure mattress pad is
attened out by pressing down
on it.

6
Folding the Bassinet
1To fold the bassinet, push the tab
aside in the opening and pull up
on the release rings on both sides
of bassinet frame to disengage the
locks.
Tab 2
While holding release rings, pull
the bassinet up to allow it to fold.
3Bassinet can stand on its own
when folded for storage.

7
Bluetooth Music Module
1
WARNING
ADVERTENCIA
Always remove module from bassinet when
child can pull themselves up.
Loosen screw on cover and
slide o unit.
2Loosen 2 screws with Phillips
screwdriver on the battery
cover and slide o the unit.
3Insert 3-AA (LR6-1.5V)
batteries.
(Batteries not included)
Replace battery lid, cover, and
secure both with screws. Do
not over-tighten screws.
3 x 1,5 V +

8
Attaching Bluetooth Music Module
Module can be attached to any
side of the bassinet frame.

9
LCD SCREEN
When the batteries are installed,
the LCD screen will read the room
temperature. After 1 to 2 seconds,
it will display the temperature in
Fahrenheit.
Press or button, the LCD
screen will turn and stay on for 30
seconds.
Press and hold the and
buttons together for 3 seconds to
change temperature display
between Fahrenheit & Celsius.
1
Using the Bluetooth Music Module
Press button again, next song will play and the LCD screen will turn on.
There are 5 built-in songs. All the music will automatically shut o after
10 minutes.
Press button six times, the music and LCD screen will turn o.
Press and hold the for 3 seconds at any time when the music is on, music
and LCD screen will turn o.
2MUSIC button -
Press and hold the button for 3
seconds, the rst song will play and
the LCD screen will turn on. The
module will automatically shut o
after 10 minutes.
Press or button to adjust
the sound level. There are 6 levels.
The Bluetooth® word mark and logos are
registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such
marks by Eveno is under license.
Other trademarks and trade names are
those of their respective owners.

10
3
BLUETOOTH button -
Press the button, the blue LED will
blink until connection is made. The LCD
screen will also be on.
Press the button again, the Bluetooth
and the LCD screen will turn o.
Bluetooth connection will
automatically shut o after 20 minutes.
You must connect to Bluetooth manually the rst time by going into the
settings on your device, select bluetooth, make sure it is on then select Lyric
Lync and wait for your device to read “Connected”. Once you are connected
you can open your music app on your device you are connecting, and press
play so that the music will play through your music box. The music box will
automatically connect with your device thereafter. If you want to connect
with other devices, turn any connected device’s Bluetooth o, then connect
manually with the new device. The music box can connect with only one
device at a time. It will only connect with the device most recently connected.
When Bluetooth is connected, the blue LED indicator will be on. It will turn o
after Bluetooth is disconnected.
When Bluetooth is on, press and hold the button for 2 seconds to switch
to the internal music, Bluetooth will automatically turn o.
4NIGHTLIGHT button -
Press the button, the low
intensity night light and LCD screen will
turn on.
Press again, it will change to the high
intensity night light.
Press the third time, the night light
and the LCD screen will turn o.
The Nightlight will automatically shut o
after 5 minutes.
5LOW BATTERY -
A low voltage icon will appear in the
upper right hand corner of the LCD screen
when the battery voltage is low.

11
BATTERY INFORMATION
• Keep these instructions for future use.
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard (carbon zinc), or rechargeable
(nickel cadmium) batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product
before being charged.
• Rechargeable batteries are only to be charged by an adult.
• Only batteries of the same or equivalent type are to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• DO NOT short-circuit the supply terminals.
• Check that all contact surfaces are clean and bright before
installing batteries.
• DO NOT submerge any part of the product in water.
• Dispose of batteries safely.
• Remove batteries when stored for long periods of non-use.
• Keep batteries out of children’s reach.
WARNING
ADVERTENCIA
Failure to follow warnings and instructions for
battery use could result in serious injury or death.

12
FCC INFORMATION
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including inter-
ference that may cause undesired operation.
WARNING!Changes or modications to this unit not ex-
pressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
This device complies with the FCC RF radiation exposure limits set
forth for an uncontrolled environment and this transmitter must not
be collocated or operated in conjunctions with any other antenna or
transmitter.
This equipment complies with IC RSS-102 RF radiation exposure limits
set forth for an uncontrolled environment and this transmitter must
not be collocated or operated in conjunctions with any other antenna
or transmitter.
CAN ICES-3 (B)/NMB-3(B).

13
Care and Cleaning
WASHING INSTRUCTIONS for bassinet, mattress cover and sheet:
- BASSINET/MATTRESS PAD: Spot clean with a damp cloth. Air dry.
NEVER USE BLEACH.
- SHEET/ MATTRESS COVER: Machine wash
separately. Cold Water. Delicate cycle.
NEVER USE BLEACH.
Tumble dry: 10-15 minutes on low heat,
remove immediately.
TO CLEAN BASSINET FRAME, wipe clean with damp cloth. NO BLEACH.
EXCESSIVE EXPOSURE TO SUN OR HEAT, could cause warping or fading
of parts.
BEFORE USING BASSINET, ALWAYS CHECK for any missing parts, torn
material or if it is broken or damaged. Replace parts as needed by
contacting CNP. NEVER USE bassinet if any parts are missing or damaged.
MATTRESS COVER

14
1.1 Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
1.2 In addition to the guarantees that cannot be excluded under the
Australian Consumer Law described in clause 1.1 and any other guarantee or
warranty implied by law, when you purchase one of our products, you will
also have the peace of mind in knowing that your product is covered by CNP
Brands Standard Warranty. The Standard Warranty is provided by C.O. White
Pty Ltd trading as CNP Brands (ABN 97 004 169 233) (“CNP Brands”). The
terms and conditions of the Standard Warranty are further described below.
1.3 Subject to clause 1.1 and the terms below, CNP Brands warrants that this
CNP Brand product, purchased by you in Australia or New Zealand:
a) is free from defects in workmanship and material, when the product is
used for normal consumer use for a period of 1 Year from the date of
purchase as evidenced by your proof of purchase (“Warranty Term”); and
b)will, when the product is used for normal consumer use, comply with the
manufacturer’s specifications during the Warranty Term.
1.4 CNP Brands agrees to repair or replace at CNP Brands cost, the product,
and any accessory supplied with the product, which is proven upon inspec-
tion by CNP Brands or a CNP Brands Authorised Service Agent not to comply
with either warranty contained in clause 1.3. Any decision to repair or replace
a product is to be made by CNP in its absolute discretion. The extent of any
repair will be to rectify any defect in workmanship and materials or to ensure
that the product complies with the manufacturer’s specifications.
1.5 To make a claim under this Standard Warranty you will need to:
a) Return the product within the Warranty Term to the place of purchase
together with your proof of purchase, where the retailer will provide you
with assistance to make your claim; or
b)Contact CNP Brands Customer Care Centre on toll free 1300 667 137
during the Warranty Term to register your claim and provide the details to
enable CNP Brands to assess the claim.
CNP Brands Warranty Information

15
1.6 You may also be required to make the product available to CNP Brands or
a CNP Brands Authorised Service Agent. If you are required to return the
product to a CNP Brands Authorised Service Agent, CNP Brands will provide
details of the centre closest to you. Unless CNP Brands decides otherwise you
are responsible for any costs associated with returning the product to CNP
Brands. The product will be at your risk whilst in transit to and from the CNP
Brands or CNP Brands Authorised Service Agent, unless transported by CNP
Brands or its agents.
1.7 In order for your claim to be processed you will need to provide to CNP
Brands with an original proof of purchase. For example an original retailer
purchase receipt, bill of sale, invoice, lay-by docket, credit card receipt or
similar proof of purchase.
1.8 If CNP Brands decide to repair a product, this product may be replaced by
refurbished products of the same type rather than being repaired.
Refurbished parts may be used to repair the product. Replacement of the
product or a part does not extend or restart the Warranty Term.
1.9 Exclusions
a) This Standard Warranty does not cover products purchased as an
ex-display, without being checked by CNP Brands or CNP Brands Authorised
Service Agents.
b)This Standard Warranty does not cover faults or defects caused by:
i. Unsuitable, improper use or use not in accordance with the manufactures
specifications;
ii. Incorrect installation or installation not in accordance with instructions
provided;
iii. Normal wear and tear;
iv. Inadequate or complete lack of maintenance;
v. Chemical, electrochemical or electrical influences; or
vi. Harsh detergents or abrasive cleaners used on product finishes.
c) To the fullest extent permitted by law, CNP Brands excludes all liability for
damage or injury to any person, damage to any property, and any indirect
consequential or other loss or damage.
CNP Brands Warranty Information (cont.)

16
©2017 EVENFLO COMPANY, INC.
1801 COMMERCE DRIVE, PIQUA, OH 45356
EVENFLO COMPANY, INC.
Distributed in Australia by:
CNP Brands, 20 Calarco Drive
Derrimut, VIC, 3030 Australia
Customer Service
tel: [phone]
email: [e-mail]
www.cnpbrands.com.au