Everdure RBBQ120S Owner's manual

DESIGNED TO PERFECTION
INSTALLATION, OPERATION
& MAINTENANCE INSTRUCTIONS
FOR EVERDURE WALL MOUNTED RANGE HOOD
Models Included:
RBBQ120S
IMBERLEY

DESIGNED TO PERFECTION
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
FOR EVERDURE WALL MOUNTED RANGE HOOD RBBQ120S
CONTENTS
SECTION PAGE NO.
Important Safety Instructions……………… 3
Appliance Details ………………………… 4
General Information …………………….. 4
What Is Supplied ………….……………… 4
What May Be Needed For Installation … 4
Installation Instructions …………………… 5-6
Operating Instructions …………………… 7-8
Replacing The Bulbs ….………………….. 9
Cleaning …………………………………… 9
Troubleshooting …………………………… 10
It is important that you retain these instructions, proof of purchase as well as
other important documents about this product for future reference.
Due to continual product development, Everdure reserves the right to alter
specifications or appearances without notice.
Dispose of packaging responsibly – recycle where facilities are available.
2

DESIGNED TO PERFECTION
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT: Read the assembly instruction section and safety precautions of this booklet
carefully before removing the contents of this carton.
1. In certain circumstances electrical appliances may be a danger hazard.
2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience or knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety. Children should
be supervised to insure that they do not play with the appliance.
3. Do not check the status of the filters or motor oil traps while the cooker hood is operating.
4. Do not touch the lights after appliance use as they may be hot.
5. Do not disconnect the appliance with wet hands and do not disconnect the power cord with extreme
force.
6. Do not flambé underneath range hood.
7. Avoid free flames, as it may cause damage to the filters and be a fire hazard.
8. If frying food, ensure to check regularly to avoid the oil overheating and becoming a fire hazard.
9. Unplug the appliance before carrying out maintenance or replacing lamps.
10. If the power cord is damaged, it must be replaced by the manufacturer, an authorised service centre or
similarly qualified persons to avoid a hazard.
11. This appliance is designed to be used in conjunction with a gas or electric cooktop with no more than 5
elements or gas or electric barbecue with a cooking area of no more than 1200mm long.
12. This appliance is for indoor use only. The appliance can be installed in a permanent roofed alfresco
area having no less than 50% permanent open wall space with adequate protection from the elements.
The appliance must be installed in accordance with local regulations and the applicable Standards.
13. When the appliance is not in use and before cleaning, unplug the appliance from the outlet.
14. It is recommended to operate the range hood prior to cooking.
15. It is recommended to leave the range hood in operation for 15 minutes after cooking is terminated in
order to completely eliminate cooking vapours and odours.
16. Turn off the range hood when not in use. Do not leave the cooking appliance unattended during use as
overheated oils or fats may catch fire.
17. Don’t use the range hood if it is damaged, especially the supply cord and the casing.
18. Don’t immerse the range hood in liquid.
19. The exhaust air must not be discharged into a flue which is used for exhausting fumes from appliance
burning gas or other fuels.
20. Regulations concerning the discharge of air have to be fulfilled. There shall be adequate ventilation of
the alfresco area when the range hood is used at the same time as appliances burning gas of other
fuels.
21. Clean the surface of the cooker hood regularly using cloth moistened with denatured alcohol of non
abrasive liquid detergent.
22. There is a fire risk if cleaning is not carried out in accordance with the instruction.
23. The filters are used to collect fats and oils. These should be removed and cleaned regularly to minimise
the chance of fire. The motor oil traps are positioned below each motor (centre rear of the appliance)
and should also be removed and cleaned regularly.
DO NOT OPERATE THIS APPLIANCE BEFORE READING THE
INSTRUCTION BOOKLET
3

DESIGNED TO PERFECTION
APPLIANCE DETAILS
Voltage: 220-240V
Frequency: 50Hz
Lamp Max: 4x1W LED lamps
Rated Input Power: RBBQ120S:544W
GENERAL INFORMATION
The range hood body and flues are
made from high quality 304 stainless
steel, and the filters are made from
430 stainless steel.
Before installing and operating the
range hood, carefully read the
following important information
regarding installation safety and
maintenance. Keep this information
booklet accessible for further
consultations.
The appliance has been designed to
exhaust cooking fumes externally.
Before installation, please ensure that
the following have been supplied and
that the tools listed below are readily
available.
Everdure recommends that this appliance is installed by a qualified technician. Any damage or injuries
caused by incorrect installation will void your warranty.
WHAT IS SUPPLIED
Range hood (including one way valve for flue x 2) x 1.
Outlet tubes Ø150mm x 2.
Installation kit x 1 – 30mm screws x 4, 40mm screws x 2, 8mm screws x 2, plastic plugs x 6.
Mounting bracket x 1.
Instruction booklet x 1.
Remote control x 1.
Remote control mounting panel x 1.
WHAT MAY BE NEEDED FOR INSTALLATION
Electric Drill Duct Tape
Tape Measure Jig Saw
Spirit Level Ladder
Screwdrivers Torch (If natural lighting is minimal)
4

DESIGNED TO PERFECTION
INSTALLATION INSTRUCTIONS
Please ensure that before installing the range hood, all power is switched off.
Installation must be in accordance to the local electrical authority and codes.
This range hood must be earthed at all times for the operators’ safety.
The switched power outlet for the range hood should be positioned to enable the user to turn the power off,
to enable cleaning and any maintenance required.
The switched power outlet should be installed within 600mm from the rear of the unit.
Ensure that when installing the range hood, that it is protected from any possible damage from tools etc.
Ducting for this unit must be installed in accordance to the local authority.
Ensure that the fixings used for this range hood are suitable.
Check the area where the range hood is to be fitted, to ensure that it is structurally sound.
The Everdure RBBQ120S range hoods are intended to be installed directly onto a wall.
INSTALLATION OF THE EVERDURE RBBQ120S RANGE HOODS DIRECTLY TO A WALL
NOTE: A single outlet model is used in these diagrams for reference only.
Ensure that the wall is structurally sound, and is capable of carrying the weight of the range hood.
The range hood can be placed at a minimum of 600mm away from an electric cooktop or 650mm minimum
from a gas cooktop. If installing above a gas barbecue, the appliance must be installed a minimum of
1200mm above the cooking surface in accordance with local
regulations and the applicable Standards. Refer to your barbecue
manual/data plate: If the manufacturer’s nominated clearance for
the barbecue is higher, follow the higher value. This appliance
should not be used in conjunction with solid fuel barbecues. The
unit is held to a wall via a mounting bracket (supplied with the unit)
and screws.
There are 3 sets of 2 holes needed to mount the appliance to the
wall. Measure up the required height of the range hood and then
add 30mm for the lowest set of holes (600mm apart). Measure up
90mm further for the centre set of holes (550mm apart). The top set
of holes (450mm apart) is determined by the final position of the
inner U-shaped cover.
Once all of the holes are marked, use a Ø8mm drill bit and drill
the six holes (as per the diagram to the right).
With all six holes drilled, fit a plastic insert into each hole,
making sure the inserts are reasonably tight and go all of the
way into the holes. Take the mounting bracket and attach it
to the wall with two 40mm screws. Take the 30mm screws
and screw them into the centre set of holes (leave a gap of
~5mm between the wall and the head of the screw. Check
that the screws are secure.
5

DESIGNED TO PERFECTION
Remove all of the filters. Using two people lift the main unit up
and hook onto the exposed screws via the two key-shaped holes
in the back of the man unit. Check that the screws are
supporting the weight before releasing the unit.
From inside the appliance, tighten the two screws. Take the
remaining 30mm screws and push them through the holes in
the rear of the main unit into the lower set of holes. Tighten into
place. Check that the main unit is completely secure and
replace the filters.
Place the flexible tubing on each of the outlets and fix in
place using the straps included.
Fit the U-shaped sections together (the inner section should have
the mounting holes and vents at the top). Place the u-shaped
sections onto the main unit. Take hold of the flexible tubing and
lengthen it out. Fix it to the outlet venting so that it cannot come
loose. Pull the inner U shaped section up and fix to the mounting
bracket with the two 8mm screws.
NOTE: Care should be taken that the range hood is fitted correctly (see diagram below). Incorrect
installation can cause a build up of grease and oils and cause damage to the unit. The ventilation tubes
should be at angles greater than 120⁰or parallel, and connected to the wall or ceiling ventilation pipes.
NOTE: Remove all protective plastic coatings from the stainless steel surfaces before use.
6

DESIGNED TO PERFECTION
OPERATING INSTRUCTIONS
FOR RBBQ120S ELECTRONICALLY OPERATED RANGEHOODS
DESCRIPTION
DESCRIPTION
01 Timer/Clock Button 05
Lamp
Indicato
r
02 Lamp Button 06
Fan Speed Indicator
03 Fan Speed Button
07
Timer
Indicato
r
04 Extraction Fan On/Off Button 08
Extraction Fan On/Off Indicato
r
09
Timer/Clock Displa
y
Note: Before the unit can be operated, it must be ducted.
Connect the plug into the power.
First, plug the range hood into the power supply. The LCD display will light up for 15 seconds.
To start any operation, press a button once so that the LCD display lights up. While it is lit, the buttons will
control the appliance.
LAMPS
The LED lamps work independently of the other functions. Press the Lamp Button (02) once to turn the LED
lamps on (Lamp Indicator (05) will also turn on). Press a second time to turn off (Lamp Indicator will turn off).
EXTRACTION FAN
To turn the extraction fan on, press the Extraction Fan On/Off Button (04). The fan will start running (starting
at high, and then dropping down to the previous setting) and the Extraction Fan On/Off Indicator (08) will
light up. The animated Fan Speed Indicator (06) will also light up. Press the Fan Speed Button (03) to cycle
the extraction fan speed up through the 3 speeds (the animated Fan Speed Indicator will change speed as
well). To turn off the extraction fan, press the Extraction Fan On/Off Button again.
SETING THE CLOCK
To set the clock, the LED lamps and the extraction fan should be off. Press and hold the Timer/Clock Button
(01) for 3 seconds until the first 2 digits of the LCD display start to flash (hours). While the digits are flashing,
use the Lamp Button (02) to adjust the time down and the Fan Speed Button (03) to adjust the time up. When
the correct hour is set, press the Timer/Clock Button again and the second 2 digits of the LCD display start to
flash (minutes). Adjust in the same manner. Once set, leave all buttons for 10 seconds and the LCD display
will stop flashing, indicating that the clock has been set.
7
02
01 03 04
05 06 09 08 07

DESIGNED TO PERFECTION
SETING THE TIMER
The timer can be used to turn off the extraction fan automatically after a period of time (from 1-60 minutes).
Note: The timer does not affect the lamps.
With the extraction fan running, press the Timer/Clock Button (01) once. The LCD display (09) and the Timer
Indicator (07) will start to flash. While the LCD is flashing, use the Lamp Button (02) to adjust the time down
and the Fan Speed Button (03) to adjust the time up (from 1-60 minutes). When the correct time has been
set, either wait 10 seconds, or press the Timer/Clock Button again. The light around the Timer/Clock Button
will flash and the time will start to count down on the LCD display. When the countdown reaches 0, the
appliance will beep and the extraction fan will turn off.
To disable the timer, press the Fan Speed Button or Extraction Fan On/Off Button.
If power is left connected to the appliance, the timer will stay programmed in, and will come up as the
default time when the timer function is recalled later.
REMOTE CONTROL
DESCRIPTION
T1 Extraction Fan Increase Button
T2 Timer Button
T3 Lamp Button
T4 Extraction Fan Decrease Button
The remote control can be used to turn on and off the extraction fan, adjust its speed,
turn the lamps on and off and start a timer (a small LED at the top corner indicates a
button pressed). It cannot be used to set the clock. To use the timer, a timer setting
must be set as per the previous section. One button on the remote control or control
panel must be pressed first so that the display lights up before any function can be changed.
If the remote control doesn’t operate the appliance, it may need to be linked to the appliance. With no
functions running, press the power button on the appliance once (LED display lights up) and then press and
hold again for 10 seconds until the indicators around the buttons begin to flash. While they are flashing,
push a button on the remote control to link the two together.
LAMPS
The LED lamps work independently of the other functions. Press the Lamp Button (T3) once to turn the LED
lamps on and a second time to turn off.
EXTRACTION FAN
Press either of the extraction fan buttons (T1 or T4) and the extraction fan will start to run. Press the Extraction
Fan Increase Button to increase the speed (low, medium & high) and the Extraction Fan Decrease Button to
decrease the speed. When the speed is at low, pressing the Extraction Fan Decrease Button one more time
will turn off the extraction fan.
RUNNING THE TIMER
The timer must already be pre-set (as per the previous section). With the extraction fan running, press the
Timer Button (T2). The LCD display will flash and then start to count down the pre-set time. When the time
finishes, the extraction fan will turn off. The lamps are not affected by this function. To disable the timer, press
either extraction fan button or the Timer Button on the remote control.
REPLACING THE REMOTE CONTROL BATTERY
8
T1
T4
T2
T3

DESIGNED TO PERFECTION
REPLACING THE LED LAMPS
The LED lamps used on the RBBQ120S cannot be changed by the consumer. In the case of a broken lamp,
please contact your nearest Everdure service centre.
CLEANING
SAFETY PRECAUTION
Before cleaning your range hood or performing any maintenance, please ensure that the range hood is
turned off at the power point.
Do not use abrasive cleaners to clean the range hood. The use of warm soapy water and a cloth are
recommended.
Ensure that the range hood is cleaned regularly, as a build up of grease and fat may occur otherwise.
The filters on the range hood must be cleaned regularly to maintain efficiency, and prevent grease build up.
It is recommended that this is undertaken every 4 – 6 weeks, depending on frequency of use.
The filters can be cleaned with warm soapy water or a cloth, or they may be washed in a dishwasher. If
washed in a dishwasher, discolouration may occur to the mesh and frame.
Cleaning of the range hood must be performed as described above, otherwise there is a possibility of a fire
hazard due to grease and fat build up.
The filters on the range hood must be cleaned regularly to maintain efficiency, and prevent grease build up.
The filter mesh is made of a high density Stainless Steel. It is recommended that this is undertaken every 4 –
6 weeks, depending on frequency of use.
The filters can be cleaned with warm soapy water or a cloth, or they may be washed in a dishwasher. If
washed in a dishwasher, discolouration may occur to the mesh and frame.
Remove filters by pulling the small tabs at one end of the filter down, which will release one end of the filter
from its mounting. Drop that end down slightly and slide the filter out of the appliance. To refit, slide the fixed
end of the filter back into the mounting, pull down on the tab and push the filter back into position.
During operation, oil tends to collect inside the motors as air passes through and out of the appliance. This
oil will pool at the bottom of the motor housing. The motor oil traps are positioned at the bottom of the
motor housing, under holes in the motor housings, where the pooled oil can drip out. Each motor oil trap
can be removed by pressing slightly upwards and then sliding sideways out of the brackets (only one
direction). Once emptied and cleaned they must be replaced. This should be done at the same time as, or
more frequently than the filters.
9

DESIGNED TO PERFECTION
TROUBLESHOOTING
Fault Possible Cause
Solution
Light on, but
motor does
not work
Fan switched off Press Extraction Fan On/Off Button.
Electronics or button
failed
Contact Everdure Service.
Motor failed Contact Everdure Service.
Light does not
work, motor
does not work
House fuses blown Reset
/
Replace fuses.
Power cord loose or disconnected
Refit cord to power outlet.
Switch power outlet on.
Oil leakage
One way valve and the air
ventilation entrance are not tightly
sealed
Take down the one way valve and
seal with sealant.
Too much oil trapped in filters or
inside appliance
Check and clean.
Lights not
working
Broken/Faulty lights
Contact Everdure Service.
Insufficient
suction
The distance between the range
hood and the cooking appliance is
too far
Refit the range hood to the correct
distance.
The Range
hood inclines
The fixing scre
w
s are
not tight
enough
Tighten the hanging scre
w
s
and
make it horizontal.
Buzzing sound
from the top of
appliance
Flexible tubing loose/damaged
Check tubing.
One way valve flaps reversed
Check spike on each flap is on the
top.
NOTE: Any electrical repairs to this appliance must conform to your local, state and federal laws.
Please contact the service centre if in any doubt before undertaking any of the above.
Always disconnect the unit from the power source when opening the unit.
This appliance is covered by a 1 year (12 month) warranty. Please check your separate warranty card for
details.
7
10

DESIGNED TO PERFECTION
OTHER PRODUCTS AVAILABLE FROM EVERDURE
Barbecues Indoor Cooking Products
11

DESIGNED TO PERFECTION
A division of Shriro Australia Pty Ltd
104 Vanessa St Kingsgrove NSW 2208
In Australia: 1300 355 541
In New Zealand: [phone]
www.everdure.com
IM Ref: RBBQ120S 18/2015/06FC
FOR INDOOR USE ONLY