EverFocus EDR410M User manual

Volume
1
Quick Installation Guide
E
ED DR R8 81 10 0M M/ /4 41 10 0M M
1

EVERFOCUS ELECTRONICS CORPORATION
EDR810M / EDR410M
Quick Install Guide
©2005 EverFocus Electronics Corp
1801 Highland Ave
Phone [phone] • Fax [phone]
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in
any form or by any means without written permission of the Everfocus Electronics
Corporation.
QuickTime is a registered trademark of the Apple Computer, Inc. Windows is a registered
trademark of the Microsoft Corporation in the United States and other countries. Linksys is a
registered trademark of the Linksys Corporation. D-Link is a registered trademark of the D-
Link Corporation. DynDNS is a registered trademark of the DynDNS.org Corporation. Other
product and company names mentioned herein may be the trademarks of their respective
owners.
2

Safety Warning
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Note:
This equipment has been tested and found to comply with the limits for a Class A digital device,
The changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note:
This is a class A product. In a domestic environment this product may cause radio interference
In which case the user may be required to take adequate measures.
Notice:
The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All
specifications are therefore subject to change without notice.
3

Safety Precautions
Refer all work related to the installation of this product to qualified service personnel or
system installers.
Do not block the ventilation opening or slots on the cover.
Do not drop metallic parts through slots.This could permanently damage the appliance.
Turn the power off immediately and contact qualified service personnel for service.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove
screws or covers. There are no user-serviceable parts inside. Contact qualified service
personnel for maintenance. Handle the appliance with care. Do not strike or shake, as this
may damage the appliance.
Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do take
immediate action if the appliance becomes wet. Turn the power off and refer servicing to
qualified service personnel. Moisture may damage the appliance and also cause electric
shock.
Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry
cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild
detergent and wipe gently.
Do not overload outlets and extension cords as this may result in a risk of fire or electric
shock.
Do not operate the appliance beyond its specified temperature, humidity or power source
ratings. Do not use the appliance in an extreme environment where high temperature or
high humidity exists. Use the appliance at temperature within indoor type DVR for 0oC ~
+40oC and a humidity below 90%. The input power source for this appliance is
AC100~240V.
4

Safety Precautions
Read Instruction — All the safety and operating instructions should be read before the unit is
operated.
Retain Instructions — The safety and operating instructions should be retained for future
reference.
Heed Warnings— All warnings on the unit and in the operating instructions should be adhered to.
Follow Instructions— All operating and use instructions should be followed.
Cleaning— Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning
Attachments—Do not use attachment not recommended by the product manufacturer as they may
cause hazards.
Water and Moisture—Do not use this unit near water-for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet basement, near a swimming pool, in
an unprotected outdoor installation, or any area which is classified as a wet
location.
Servicing—Do not attempt to service this unit by yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified
service personnel.
Power Cord Protection—Power supply cords should be routed so that they are not likely to be
5

Installation
The installations described below should be made by qualified service personnel
or system installers.
The EDR810M & EDR410M are the full-featured digital video recorders
designed specifically for use in mobile applications. Please refer to the following
Quick Installation Guide for installing EDR810M or EDR410M into mobile
applications such as buses, cars and police cruisers.
The DVR can be mounted horizontally (suspend or support mounted).
Support
Suspend
Interface
Interface
EDR410M
EDR41
0M
Show all the possible ways to mount the DVR.
Use the two Z-brackets supplied to mount it in any ways shown.
Support
Suspend
EDS
EDS
6

Quick Install Guide:
1. Unpack Everything
Make sure you have everything you need before you begin the
installation.
2. Equipment Required
The following tools may help you to complete the installation:
•Drill
•Screwdrivers
•Wire cutters
Avoid any location for installation:
•That is subject to high vibration
•That is subject to high sunlight levels
•That is subject to drenched of the rain
•Where passengers can interfere with unit
•Next to a heater duct
The following table lists the recommended location options.
3. Choosing the Location
Choose a location for installation that:
•Provides convenient access for installing or removing the hard drive
•Allows air to flow around the fan vents. Inadequate or improper air flow can impede
proper operation of the unit
7

Possible Installation Locations inside the Automobile Vehicle: TOYOTA
CAMRY
Glove box (inside or underneath)
Trunk (Users are suggested to use
“suspend” for mounting option)
Passenger seat (underneath)
Drive seat (between seat and wall)
Show the wiring on the wiring harness that connects to the electrical system
8

Glove box (inside or underneath)
Possible Installation Locations inside the Automobile Vehicle: Truck
Drive seat (between seat and wall) or Passenger seat (underneath)
(Users are suggested to use “support” for mounting option)
Show the wiring on the wiring harness that connects to the electrical system.
(
24 V
)
(
5
A)
9

Installing the Camera(s) and Monitor
The DVR is typically connected to one camera installed inside the car. Other camera(s) can also be
installed in different locations (for example, use the waterproof camera to the outside of vehicle).
For installation procedure, refer to the guide that came with the camera(s) you purchased.
The Monitor power supply connects from the automotive adapter (cigarette plug) Monitor and
cameras must be purchased separately.
LCD Monitor
LCD Monitor
Connect the Camera(s)
Connect the power connector from the camera(s) harness into the CAMERA POWER OUT jack
on the back panel of the DVR.
Connect the primary camera(s) video connector to the CAMERA INPUT and the audio connector
to the AUDIO INPUT in the back panel.
Adjust the camera(s). After the camera is installed, connect a monitor directly to the camera and
observe the image.
Make any adjustment if necessary.
10