EverFocus EQN100 User manual

EQN100 Mini Cube IP Camera
Auto White Balance, 3DNR
Quick Installation Guide
Copyright © EverFocus Electronics Corp.
Release Date: August, 2015

1
Introduction
The EQN100 Mini Cube IP Camera is designed for indoor use. The camera comes with
1.3MP, providing up to 30fps at 1280 x 1024 viewing resolution.
Physical Description
1 2
Front View Rear View
3 4
Cable
No. Item Name Descriptions
1 Lens Fix focal lens 6mm (optional:2.8mm, 3.6mm, 8mm)
2 Reset Button
Use a paper click to press and hold the Reset Button for 2
seconds and then release the button for 2 seconds. Repeat
doing this 3 times to reset all configurations to factory default.
3 LAN Cable Connects to a router.
4 Power Cable Connects to a 12VDC power source.
Dimensions

2
Packing List
•Camera x 1 •Quick Installation Guide x 1
Note: Equipment configurations and supplied accessories vary by country. Please consult
your local EverFocus office or agents for more information. Please also keep the shipping
carton for possible future use. Contact the shipper if any items appear to have been
damaged in the shipping process.
Optional Accessory
You can use the optional accessories to expand the capabilities and versatility of the camera.
Please contact your dealer for more information.
•IP Sidekick - ESK1000
Using it for installation, you do not need to pre-configure the
IP address or to use an additional monitor to check and
adjust all the IP cameras. The product can assign an IP
address to the camera, and then you can connect and check
the camera live view using our mobile app EF Sidekick. For
details about IP Sidekick, please refer to the IP Sidekick –
ESK1000 User’s Manual.
•Bracket - BA-EQN
You can use the bracket to install EQN100
onto the desired surface.
*Two M3*5 screws and two washers are
included for screwing the camera to bracket.
Installation
To install this IP camera, you have to prepare 4 screws (M3 with max length of 2mm) and
then screw the camera to the installation surface. The four screw holes on the camera are
illustrated below (top / bottom / left / right). Please be noted the Top screw hole should
face up in order to display correct camera view position.
Top

3
Accessing the Camera
You can look up the IP address and access the Web interface of the camera using the IP
Utility (IPU) software, which can be downloaded from the EverFocus’ Website
(http://www.everfocus.com.tw/HQ/Support/DownloadCenter_p1.aspx). You can also
download the User’s Manual from EverFocus’ Website. Please connect the IP camera on the
same LAN of your computer. Please check that your computer supports Microsoft Windows
XP/2003/Win7/Vista.
1. Extract the files after downloading the IP Utility to your computer. Double click the IP
Utility Setup.exe and follow the on-screen instructions to install the IP Utility.
2. Click the Finish button, the IP Utility will be automatically launched to search the IP
devices connected on the same LAN.
3. To access the Live View window, double click the IP address of the device, the login
window appears.

4
4. Download and install the ActiveX file by clicking File on the login window. Click Run and
follow the instructions to install the program. Click Finish to complete the process.
5. On the login window, type the user ID and password to log in. By default, the user ID is
user1 and the password is 11111111. Click Login, the Live View window appears.
Note: Before start operating the IP camera, please make sure the camera date and
time are correct. To configure the camera date/time, go to Config > System > System
Time on the Web UI.

5
Connecting to the Network
You can use one of the methods below to connect the camera to the network.
One-to-One Connection (Directly from PC to IP camera)
You can connect directly without using a switch, router or modem. However, only the PC
connected to the camera will be able to view the IP camera. You will also have to manually
assign a compatible IP address to both the computer and the IP camera. Unless the PC has
another network connection, the IP camera will be the only network device visible to the PC.
See the diagram below:
Cat 5
Right: Pinout of a crossed-over cable.
Network Cable Crossed-Over
Pin No. Wire Color Wire Becomes
Pin 1 – Orange/White
Pin 2 – Orange
Pin 3 – Green/White
Pin 4 – Blue
Pin 5 – Blue/White
Pin 6 – Green
Pin 7 – Brown/White
Pin 8 – Brown
13
26
31
6 2
Direct High-Speed Connection
In a Direct High-Speed Connection, the camera connects directly to a modem without the
need for a router. You need to set the static or dynamic WAN IP address assigned by your
ISP (Internet Service Provider) in the camera’s configuration web pages. To access the
camera, just type “http://xxx.xxx.xxx.xxx”, where xxx.xxx.xxx.xxx is the IP address given by
your ISP. If you have a dynamic IP address, this connection may require that you use DDNS
for a reliable connection. Please refer to 7.3.7 DDNS Settingsin the User’s Manual.
Cat 5
Straight Through Cable
High-speed modem
Internet

6
Router or LAN Connection
This is the most common connection in which the IP camera is connected to a router and
allows multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The
camera must be assigned an IP address that is compatible with its LAN. By setting up port
forwarding on the router, you can remotely access the cameras from outside of the LAN via
the Internet. To remotely access the Web interface of the IP camera, please refer to 7.3.7
DDNS Settings in the User’s Manual. To set up port forwarding, please consult the manual of
the router.
High-speed modem
Internet
Straight-through LAN patch cable
Router
Cat 5 Straight Through Cable
Network Cable Straight-Through
Pin No. Wire Color Wire Becomes
Pin 1 – Orange/White
Pin 2 – Orange
Pin 3 – Green/White
Pin 4 – Blue
Pin 5 – Blue/White
Pin 6 – Green
Pin 7 – Brown/White
Pin 8 – Brown
1 1
2 2
3 3
6 6
Above: Pinout of a straight-through cable.
Upgrading Firmware
You can upgrade camera’s firmware through the Web UI of the IP camera.
On the Web UI, click Config > System > Upgrade to enter the Upgrade setting page.
Click the Browse button to find a previously prepared firmware upgrade file. Click the
Upgrade button to install the new firmware. The upgrading status will be displayed.
When the upgrade process is complete, the IP camera will restart automatically.
Note: Do not disconnect power and the network to the IP camera during the upgrade
sequence. The IP camera will reboot automatically after the upgrade has completed.

7
EverFocus Electronics Corp.
EverFocus Taiwan HQ:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road, Hsi-Chih, New Taipei City, Taiwan
TEL: [phone] FAX: [phone]
www.everfocus.com.tw [e-mail]
P/N: 4605PQ0100B022C