EverFocus EMN2560 User manual

EMN2560
5-Megapixel IR & WDR,
Outdoor Mini Fixed Dome Network Camera
Quick Installation Guide
Copyright © EverFocus Electronics Corp.
Release Date: April, 2021
All the images including product pictures or screen shots in this document are for example only.
The images may vary depending on the product and software version. Information contained in
this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone]FAX: [phone]www.everfocus.com.tw

1
1. Physical Description
1
2
3
4
No.
Item Name
Descriptions
1
Light Sensor
Detects lights.
2
IR LEDs
IR LEDs for infrared illumination in night vision applications.
3
Lens
Camera Lens.
4 Micro SD Card Slot
Insert a micro SD card. Please go to the product page on
EverFocus website to see the latest Storage Compatibility List.
http://www.everfocus.com.tw
Dimensions

2
Packing List
Please check that there is no missing item in the package before installing.
EMN2560
1. Camera x 1
2. MAC Address Sticker x 2
3. Cable Gland Kit x 1 (connect to the LAN/PoE cable for waterproofing)
4. Screw x 4 (With Screw Anchor x 4; to lock the Mounting Plate)
5. Small Screw x 2 (to lock the camera base to the mounting plate)
6. Angle Adjustment Tool x1
7. Desiccant Bag x 1
8. Hexagon Wrench x 1
9. Mounting Sticker x 1
10. Mounting Plate x 1
11. Quick Installation Guide x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult
your local EverFocus office or agents for more information. Please also keep the
shipping carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
2. Cables
The cables provide connections for network and power.
LAN / PoE Cable
12VDC Power Input

3
3. Installation
1. Before screwing the camera to the wall, stick the supplied Mounting Sticker on the wall /
ceiling to mark the positions for installation. Drill four holes on the wall / ceiling according
to the supplied sticker and push the supplied four Screw Anchors into the four holes on
the wall / ceiling. Drill another hole in the middle of the Sticker if you wish to run the
wires through the wall / ceiling.
Wall / Ceiling
2. Attach the Mounting Plate onto the wall, use the supplied 4 Screws to mount it on the
wall.
Wall / Ceiling
3. Remove the camera cover by unscrewing the four screws using the supplied Hexagon
Wrench.

4
4. Screw the camera module to the Mounting Plate:
a. Before mounting the camera module onto the Mounting Plate, thread the cables
through the wall or along the wall.
Through the wall / ceiling: run the cables through the hole on the wall / ceiling.
Along the wall: break the side cut plate on the Mounting Plate and then run the cable
from the side cut.
b. Use the supplied 2 Small Screws to lock the camera module to the Mounting Plate.
Camera Module
Mounting Plate
5. Connect the camera to power. You can either connect the camera to a 12VDC power
source or to a PoE switch using the PoE cable.
6. Connect the camera to the network using the supplied Cable Gland Kit.
a. Insert a RJ-45 network cable (without the RJ-45 connector on the one end) through
the supplied Waterproof Ring, Cable Gland, Stopper and Screw Cap accordingly.
Waterproof Ring Cable Gland Stopper Screw Cap

5
b. Connect the RJ-45 cable to the LAN/PoE Cable of the camera.
RJ-45 Cable
LAN/PoE Cable
c. Tightly screw the Cable Gland and Screw Cap to the Rugged RJ-45 Connector Cable.
Screw Cap
Cable Gland
d. Crimp the RJ-45 connector onto the RJ-45 network cable. Note that the wires should
be placed into the RJ-45 connector based on the following order (from left to right).
Orange with white stripe
Orange
Green with white stripe
Blue
Blue with white stripe
Green
Brown with white stripe
Brown
7. Optionally insert a micro SD card into the card slot (please refer to 1. Physical
Description).
8. Access the web interface of IP camera (please refer to chapter 4. Accessing the Camera),
and check if the camera is facing toward your desired direction.
9. To adjust camera viewing angles, loosen the screw to adjust the pan / tilt / rotate angles.
You can optionally use the Angle Adjustment Tool to tilt and rotate the angle to your
desired direction.
Use Angle Adjustment Tool
to tilt and rotate the angle

6
10. Before screwing back the camera cover, remove the 2 Desiccant Bags from the inner
side of the Camera Cover and replace them with the supplied Desiccant Bag. Screw the
camera cover back to the camera.
Remove the 2 Desiccant Bags
Note: Please screw back the
Camera Cover immediately
after replacing the Desiccant
Bag to reduce the absorption
capacity of the Desiccant Bag
inside the camera body.
11. Screw back the Camera Cover, and the installation is complete.
4. Accessing the Camera
You can look up the IP address of the IP camera using the IP Utility (IPU) program. You can
download the IP Utility from EverFocus website (key word search: "IP Utility").
The default network is DHCP. However, if there is no dynamic IP address assigned to the
device, its IP will switch to 192.168.0.10. By default, the ID is admin and there is no
password. Please input a password for the first-time login.