EverFocus EIP220 User manual

IP99 Series
EIP220 Network Camera
Install Guide
Copyright © EverFocus Electronics Corp,
Release: Oct. 2008

This document shows you how to install IP99 camera step by step
1. Read the product introduction and package content
2. Read the specification and diagram
3. See hardware overview
4. Do wiring and installation
5. Do network connection
Product introduction
IP99 series IP products provides built-in, easy-to-use, and browser-based management
software that can manage, view, record multiples IP99 cameras and video servers. No
additional software required. It supports flexible layout of live/playback views, easy-to-
use on-screen PTZ control, and instant zoom in/out. The true tri-plex gives users
simultaneous live view, playback, and record experience. The auto-overwritten recording
function allows IP99 IP camera can be used as a DVR-like recording, avoided disk
writing overflow.
IP99 series camera
This product comprises a web-based user interface, user-friendly feature facilitates
installation procedure. Moreover the open system structure saves the cost of coaxial cable
demand while improving quality of the image. IP99 series is a flexible and effective
solution for an interactive surveillance and remote surveillance system. It is easy to install
and easy to use.
Product features
Easy to use — IP99 series is easy to use, the only thing you need to do is to assign a
valid IP address. The only firmware required for this series is Microsoft IE 4.X or above.
Low cost — It provides a reliable and low cost video source. No need of expensive
firmware, management station nor expensive video cable.
Open environment — Supports TCP/IP network, SMTP E-mail, HTTP and other related
network protocols.
Easy management — Using standard web browser, you can assign and manage IP99
series directly through web page. It is even possible to upgrade firmware remotely.
Standard video format — IP99 series use MPEG 4 comclickion technology to produce

high quality images. User can view the images through any web browser.
Widely applicable — IP99 series provides live images on the network, it enhances
functionality of traditional television system. IP99 series allows direct connection to visit
remote video through standard IE, user can view local image as well as remote video any
time any where. IP 99 series can be used for alarm surveillance, traffic surveillance,
banking application, parking lot, factory surveillance, industry surveillance. Moreover,
IP99 series supports SMTP e-mail which allows the system to send out event image as an
attachment of the e-mail when an event occurs.
External connection — External devices include: IR sensor, switch, alarm relay or other
device that can trigger IP99 series.
PTZ connection — You can adjust camera’s direction by connecting a PTZ device to
IP99 series through a RS485 interface.
Security — IP99 series includes a web server, meaning that it can process safety control
as any other server. Web administrator can decide which individual, group, company or
even the whole world to visit your IP camera. This protection can be done by setting user
authority in IP99 series, or by connecting to a company’s internet.
Package Content
Network Camera
Quick Start Guide
CD( Install Gudie, Manual, IP99 Searcher Tool)
Optional Accessories & Related Product
3.5~8 Lens
5~50 Lens
BA-01 Bracket
BA-03 Bracket
Testing Monitor EN220

SPECIFICATIONS
CAMERA
Pickup Device 1/3" Sony Super HAD Interlaced CCD
Video Format NTSC/PAL
Pixel Effective NTSC: 510 (H) x 492 (V); PAL: 500 (H) x 582 (V)
Sensitivity 0.3 Lux / F=1.2
Day & Night Yes
Lens C/CS Mount
Video Output BNC socket, composite 1 V p-p / 75Ω
Video Output Resolution 380 TVL
AUDIO
Audio Input One way audio
Audio Format A-Low/u-Low
VIDEO
Electronic Shutter Auto/Manual
Backlight Comp. On/Off
Mirror On/Off
Auto Iris Direct Drive Switch
AGC/Brightness/Contrast/Color Adjustable
Video Comclickion MPEG-4
Video Resolution
D1: 720x480 (NTSC) 720x576 (PAL)
Half D1: 720x240 (NTSC) 720x288 (PAL)
CIF: 352x240 (NTSC) 352x288 (PAL)
QCIF: 176x120 (NTSC) 176x144 (PAL)
Frame Rate Up to 30fps
NETWORK
Interface 10Base-T/100Base-TX auto-negotiation, RJ-45 socket
Supported Protocols HTTP, TCP / IP, UDP, FTP, NTP,SMTP, DHCP, DNS, DDNS, PPPOE
Network Security 3 Level Security Protection
Max. Client Limit 20 simultaneous clients
PTZ Device Control RS485 (Pelco-P/Pelco-D)
RECORDING
Manual Recording
Up to 30fps
Motion Detection Recording Up to 30 sec. pre-event recording and 60 sec. post-event recording
Alarm Recording Up to 30 sec. pre-event recording and 60 sec. post-event recording

MOTION DETECTION &
ALARM
Physical Alarm I/O 2 CH alarm input/2 CH alarm output
Notification Record video to PC , Send email notification ( jpeg file ), FTP upload upon
motion detection and alarm trigger
Manual Trigger Alarm Output Yes, High or Low Button in Alarm Setting
PLAYBACK
Playback Video Source
Local PC
Playback Speed Forward x2, x4, x16, x32. Rewind x1, x2,x4,x16,x32
POWER
Power Supply 12 VDC
Power Consumption 9W max
PHYSICAL
Weight 340g/0.749lbs
Dimensions 66.5mm(W)x143.3mm(D)x59.3mm(H) ; 2.66”(W)x5.73”(D) x 2.37”(H)
ENVIRONMENTAL
Operating Temp. -10°C ~ 50°C / 14°F ~ 122°F
Humidity 20%~80%
Dimension Diagram
59.3mm/2.37”(H)
143.3mm/5.73”(D)
66.5mm/2.66”(W)

Hardware Overview
1. Reset: loading factory default configuration by pressing the button, which is
inside this hole. Please insert the keen-edged device to the hole for 10 seconds.
2. RS485(Pelco-P/Pelco-D): RS 485 Connector functionally reserved for PTZ
control.
3. Power LED: Power LED will light up when power is ON.
4. Ethernet RJ-45 port: Connect to LAN via this standard RJ-45 connector.
5. Power 12VDC: Connect with power adaptor
6. Video Out: Loopthrough connection to the video signal from the Video In
connector. Terminated with a coaxial/BNC connector.
7. Alarm In/Out: Connect to Alarm In/Out device.
2
4
5
6
7
1
3

Installation
a. Mount camera bracket BA-01, BA-03 (optional) on the wall. And screw it on the
wall firmly.
b. Mount Camera on the bracket
c. Connect a lens on the camera. Connect DC iris plug if using DC auto iris lens
d. Connect 12VDC power.
e. Connect BNC to testing monitor and adjust lens focus and zoom, view angle.
f. Connect CAT5 cable and do network connection. Refer to 3. Network Connection
g. Install IP searcher tool and assign IP address if you connect to multiple cameras.
See Manual for detail of IP99 searcher tool
Network Connection
This section tell you how to do different types of network connections to IP99
1. Router or LAN connection
This is the most common connection that allows multiples PC to see IP99 cameras/
encoders in pre-existing LAN through a router.
By doing port forwarding, you can view camera outside of internal LAN on internet.

2. Direct High Speed Connection
Direct High Speed Connection connect camera directly to modem without a router.
You need to assign the IP address you obtain from internet service provider to IP camera/
Encoder. To access the camera, just type http:// IP address of your internet provider. If
you have a dynamic IP address, this connection doesn’t work for you.
3. One to one connection from PC to IPcamera
With a cross-over cable, you can connect directly without switching. However, only
the PC connecting to camera can view the IP camera.