EverFocus ED610 User manual

1/3” CCD Color Day/Night
plus Wide Dynamic Range
Outdoor Vandal Dome Camera
Operation Instructions
Model No. ED610
Please read this manual first for correct installation and operation. This manual should be retained for future reference.
The information in this manual was current when published. The manufacturer reserves the right to revise and improve
its products. All specifications are therefore subject to change without notice.
PREC UTIONS
1. Do not install the camera near electric or magnetic fields.
Install the camera away from T /radio transmitters, magnets, electric motors, transformers and audio speakers
since the electromagnetic fields generated from these devices may distort the video image.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce materials
other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.
3. Try and avoid facing the camera toward the sun.
In some circumstances, direct sunlight or may cause permanent damage to the sensor and/or internal circuits.
4. Keep the power cord away from water and other liquids and never touch the power cord with wet hands.
Touching a wet power cord with hands or touching the power cord with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
Do not touch the surface of the sensor directly with the hands. Use a damp soft cloth to remove any dirt from the
camera body. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens.
Please do not use complex solvents, corrosive or abrasive agents for cleaning.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the camera at temperatures within -10℃ ~ 50℃ (14℉~122℉) and in an IP66 complaint environment; this
device is not rated as submersible. The input power source is 12 DC/24 AC.

- 1 -
T BLE OF CONTENTS
1. PRODUCT O ER IEW ...............................................................................................................3
1.1 Main Features ............................................................................................................................................... 3
1.2 Content List................................................................................................................................................... 3
1.3 Specifications................................................................................................................................................ 5
1.4 Dimensions...............................................................................................................................6
1.5 Camera Component Description .................................................................................................7
1.6 Front and Back Panel Layout......................................................................................................8
1.7 Related Products....................................................................................................................9
2. INSTALLATION...................................................................................................................10
2.1 Mounting Camera....................................................................................................................10
2.1 .1 Drill the Holes .......................................................................................................................................... 10
2.1.2 Mounting...................................................................................................................................................11
2.2 Adjusting Camera....................................................................................................................13
2.2.1 Adjusting Camera Position ......................................................................................................................... 13
2.2.2 Adjusting Zoom and Focus......................................................................................................................... 14
2.2.3 Camera Setting ....................................................................................................................16
2.2.3.1 OSD User Setup Menu ........................................................................................................................... 16
2.2.4 Close the Camera Cover (after installation is complete) ................................................................................ 16
3. OSD MENU & CONFIGURATION...............................................................................................18
3.1 Access the user setup menu screen............................................................................................................... 18
3.2 ED610 Menu Tree........................................................................................................................................ 19
3.3 LENS.......................................................................................................................................................... 22
3.4 EXPOSURE................................................................................................................................................ 22
3.4.1 SHUTTER................................................................................................................................................ 22

- 2 -
3.4.2 AGC (Auto Gain Control)............................................................................................................................ 22
3.4.3 SENSE-UP............................................................................................................................................... 22
3.4.4 BLC ......................................................................................................................................................... 23
3.4.5 HSBLC..................................................................................................................................................... 24
3.4.6 D-WDR .................................................................................................................................................... 24
3.4.7 Return...................................................................................................................................................... 24
3.5 WHITE BALANCE CONTROL....................................................................................................................... 25
3.6 DAY NIGHT................................................................................................................................................. 25
3.7 3DNR ......................................................................................................................................................... 26
3.8 SPECIAL .................................................................................................................................................... 26
3.8.1 CAM TITLE............................................................................................................................................... 26
3.8.2 D-EFFECT ............................................................................................................................................... 27
3.8.3 MOTION .................................................................................................................................................. 28
3.8.4 PRI ACY ................................................................................................................................................. 29
3.8.5 SYNC ...................................................................................................................................................... 29
3.8.6 LANGUAGE ............................................................................................................................................. 29
3.8.7 RETURN.................................................................................................................................................. 29
3.9 ADJUST...................................................................................................................................................... 29
3.9.1 SHARPNESS ........................................................................................................................................... 29
3.9.2 BLUE....................................................................................................................................................... 30
3.9.3 RED......................................................................................................................................................... 30
3.9.4 RETURN.................................................................................................................................................. 30
3.10 RESET...................................................................................................................................................... 30
3.10.1 FACTORY RESET................................................................................................................................... 30
3.10.2 RETURN................................................................................................................................................ 30
3.11 EXIT ......................................................................................................................................................... 30

- 3 -
1. PRODUCT OVERVIEW
Amazing color low light sensitivity of .05 lux before the added benefits of digital signal processing
technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus
ED610. Get color without compromise: 560T L resolution, your choice of full motion color or true
day/night images in low light without ghosting, plus 120dB Digital Wide Dynamic Range to handle the
most challenging of bright or unbalanced scene lighting conditions. andal resistant, IP66, with varifocal
auto iris lens, 3-axis positioning, dual voltage operation and a full suite of OSD Menu and DSP
functions (3D-DNR to save D R HDD space, privacy masking, 32X digital zoom, mirroring and rotation,
256X sens-up to a max of .0002 lux, and much more) this is the camera you have been waiting for, and
might be the only camera you’ll ever need.
1.1 Main Features
Super HAD II sensor at .05 lux has 5X better native light sensitivity before DSP low light boost
Color without compromise: your choice of full motion color or true day/night images in low light
without ghosting
True Day/Night with ICR module
Starlight super high sensitivity of 0.0002 Lux/F=1.2 is achieved through a sensitivity increase
setting of up to 256x
Digital Wide Dynamic Range expansion to deliver properly exposed images despite bright light
sources, deep shadows and/or unbalanced lighting in the same scene
Provides 3D-Noise Reduction to improve picture clarity while enabling D Rs to improve disk
storage utilization
3 axis positioning for wall or ceiling mounting with flexible angle viewing
Easy to use OSD setup menu
Motion detection for 4 configurable zones
Privacy mask function for 8 configurable zones
Provides digital zoom up to 32x
Dual voltage (12 DC/24 AC) with line lock to AC supply
1.2 Content List
Please be careful when you unpack the box and the electronic devices inside. Check and make
sure that you have all the items listed below inside the original box:
Camera Unit x 1
This Operation Manual x 1
Mounting kit includes:
-Long Screws x 3 (for mounting the base)
-Expanding Anchors x 3
-Washers x 3
Installation Template Sticker x 1

- 4 -
ideo Test Cable x 1
Power Adapter Cable x 1
Desiccant Pack x 1
Focus Aiding Lens Cap (for 9~22mm models only) x 1
Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton
and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales
Representative or Customer Service. The shipping carton is the safest container in which the unit may
be transported. Save it for possible future use.

- 5 -
1.3 Specifications
Items Parameter
Pickup Device 1/3" SONY Super HAD II CCD
ideo Format NTSC or PAL
Scanning System NTSC:525 T L, 60 fields/sec
PAL:625 T L, 50 fields/sec
Picture Elements 768 x 494(NTSC); 752 x 582 (PAL)
Horizontal Resolution 560 T L
Sensitivity 0.05Lux/F=1.2(AGC ON); 0.0002Lux/F=1.2(Sens-up 256x)
S/N Ratio Over 52dB (AGC off)
Electronic Shutter 1/50 (1/60) ~1/100,000
ideo Outputs 1. BNC 1.0 p-p ,75ohm
2. Additional testing video output 1.0 p-p, 75ohm
Gamma Correction 0.45
Lens Type ari-focal lens, Auto Iris, 2.8-10mm (M B), 9-22mm (M 2)
Back Light Comp. OFF, BLC, HSBLC Selectable
Auto Gain Control Off/Low/Middle/High Selectable
White Balance ATW/AWB/AWC/Manual/Indoor/Outdoor Selectable
Sync. Mode Internal/Line lock external sync.
Day & Night Yes, (Auto, Color, B/W,EXT)
OSD Menu Yes
3DNR Off/On switchable
D-WDR Outdoor, Indoor
Digital Slow Shutter Sens-Up ~ 256x
Mirror Off/Mirror/ -Flip/Rotate Selectable
Digital Zoom Off/On switchable (up to 32X)
Motion Detection Off/On for 4 Zones
Privacy Mask Off/On for 8 Zones
Weatherproof IP66
andal Resistant Yes
Power Source 12 DC/24 AC
Power Consumption 12 DC:3W max.
24 AC:3W max.
Operating Temperature -10°C~50°C ; 14°F~122°F
Weatherproof IP66
Dimensions 123mm(O.D.) x 107.8mm (H) ; 4.8” (O.D.) x 4.2” (H)
Weight 0.74 kg / 1.6 lbs
Certifications CE/FCC

- 6 -
Ø 5.143mm//0.2”
Ø 94.7mm/3.78”
1.4 Dimensions
123mm x 107.8mm ; 4.8” x 4.2”

- 7 -
1.5 Camera Component Description
Exterior view
Interior view
Rotatable cover
Outer Cover ring
Base
OSD joystick
Power board

- 8 -
(1)
1.6 Front and Back Panel Layout
Front Panel Layout:
Back Panel Layout:
(6)
(4)
(2)
(5)
(7)
(3)

- 9 -
(1) External Light Sensor
External Light sensor is used to detect the lighting level the environment. (The light sensor
is “down” when the internal camera module is properly positioned).
(2) Focus Ring
To set the focus, and loosen the focus ring knob, and turn the ring toward <F> or <N> as
necessary, and re-tighten when the adjustment is complete.
(3) Zoom Ring
To adjust the viewing angle, loosen the zoom ring knob. Turn the ring toward <W> to Zoom
out or <T> to Zoom in as necessary, and re-tighten when the adjustment is complete.
(4) Lens
The included vari-focal, DC iris lens allows manual adjustment of the field of view (zoom & focus).
The choices for focal length range are:
2.8-10mm
9-22mm
(5) Power & Video pigtail cable
Connect power and video to pigtail cable
(6) Test Video Output Connector
When installing the camera, you can use this video connector to connect a portable monitor. This will
allow you to easily adjust camera’s field of view and focus.
(7) OSD Menu joystick: Use the joystick to move the cursor Upwards/Downwards. This is used to
select the item to be set.
Tilt the stick to the right or left. This is used to select or adjust the parameters of the selected item.
Press in on the stick to enter the setup menu. If the item has its own setting menu (sign ), press
the stick again to display the sub- menu.
1.7 Related Products
In addition, you may order the following EverFocus products which are recommended for use with the
camera to achieve the best performance:
L Type Bracket: BA-EDMS
EN220 5.6 inch LCD Test Monitor

- 10 -
2. INSTALLATION
This chapter will describe, in general terms, how to install the ED610 camera.
STEPS:
2.1. Mounting Camera:
1. Drill the Holes. See 2.1.1
2. Mounting: See 2.1.2
2.2. Adjusting Camera:
1. Adjust the camera position. See 2.2.1
2. Adjusting Zoom and Focus See 2.2.2
3. Camera Setting. See 2.2.3
4. How to close camera cover after installation. See 2.2.4
Warning
• To prevent electrical shock, turn off the electrical power before making electrical connections.
• Do not expose the camera to water or moisture while open during installation, nor try to operate
it while open in wet areas. Once properly installed and sealed, the dome is IP66 rated against
water infiltration.
2.1 Mounting Camera
2.1 .1 Drill the Holes
1. Paste the drilling template on the ceiling or wall
2. Drill 4 holes, 1 for the power/video cable, 3 for screws A, B and C.
Installation sticker
Screw hole A
Screw hole B
Screw hole C

- 11 -
2.1.2 Mounting
1. Take off camera’s cover by rotating the cover counter clockwise.
Loose outer cover ring first
Take off camera’s cover
Power/ ideo Cable
Camera base Screw A,B,C
Wire outlet hole for
Surface mounting

- 12 -
2. Pull the cables to be connected to the power and video cables from the ceiling or wall.
3. Fix the camera base to ceiling or wall by using 3 screws and washers. The washers are used to
create the IP66 seal and must be used.
Ceiling Mount:
ideo output Power input

- 13 -
Wall Mount:
2.2 djusting Camera
2.2.1 djusting Camera Position
Adjust the camera to best angle for viewing.
Module can be adjusted up and down
When you install on the ceiling, change angle of view by turning these joints.

- 14 -
2.2.2 djusting Zoom and Focus
It is highly recommended to use an EverFocus Test Monitor to set up the camera. Find the ideo test
connection on the back of the camera module. Connect using the video cable included in the package.
1. Loosen the zoom ring knob, and then turn the ring towards <W> or <T> as necessary to obtain the
desired view angle.
W side (Zoom out)
The viewing range will be wider and the subject is smaller.
T side (Zoom in)
The viewing range will be smaller and the subject is larger.
2. Loosen the focus ring knob, then turn the ring towards <∞> or <N> as necessary to obtain a clear
video image.
3. Repeat steps 1 and 2 until the best image is obtained. Once the lens setting is complete, tighten
the zoom and focus ring knobs.
Important Note when focusing a 9-22mm Lens
To adjust lens zoom and focus, if using the 9~22mm lens model ED610 camera, the focus aiding lens
cap must be used to simulate the dome being closed. Follow the steps below to ensure that camera
will stay in focus when the dome is installed.
Step 1 Take the included focus aiding lens cap (shown below) from its small plastic bag.
ideo out
Connect with Test Monitor

- 15 -
Step 2 Open the dome cover and place the Focus aiding lens cap on the lens, making sure that the
cap’s notch is resting on the zoom knob.
Step 3 With cap on, adjust the focus and zoom rings by loosening the knobs and turning the rings
until subject is in focus. Retighten the knobs when done.
Step 4 When finished adjusting focus and zoom, remove the focus aiding cap from the camera lens,
replace the dome cover and secure the cover by turning it clockwise. See Section 2.2.4 below for
additional information.
NOTE: It is recommended to put the desiccant pack under the bracket. Or, use a cable tie to secure it
before placing the cover back on the camera.

- 16 -
2.2.3 Camera Setting
2.2.3.1 OSD User Setup Menu
This camera utilizes an On Screen Display (OSD) user setup menu.
Please refer to Chapter 3 OSD Menu & Configuration, to get more details about OSD menu usage.
2.2.4 Close the Camera Cover (after installation is complete)
The ED610 is specially designed with one inner cover and one outer cover ring for water-proofing and
ease of installation. Please follow these instructions for closing the camera cover.
1. Align the window in the cover with the lens
2. Push the interior cover toward the base, until it completely covers the whole red gasket and is lined
up parallel with camera base. (The cover must be aligned with the camera base or it cannot be
closed. Then turn the outer cover ring clockwise to secure it tightly to the camera base.
Push the inner cover and
cover the whole red gasket
Outer cover ring

- 17 -
Turn the external ring
3. If the lens is not aligned with the window, loosen the outer cover, adjust the inner cover so that the
lens aimed exactly at the window.
4. Tighten the outer cover ring until it is firmly secured.
Slightly adjust the cover
Correct
Wrong (not aligned)

- 18 -
3. OSD MENU & CONFIGUR TION
This chapter introduces how to configure the camera OSD menu.
3.1 ccess the user setup menu screen
I. Press inward on the end of the joystick
The menu screen will appear on the monitor.
II. Navigating with the joystick
Angle the joystick  or  to move the cursor up or down. Angle the joystick  or  to
adjust the mode or value of a setting.
III. Switching to sub-menu screens
When an item with sub-menu is selected, press inward on the end of the joystick to
switch to the sub-menu for further settings.
NOTE:
For those selected items with “ ” sign at the end, there is a sub-menu for further settings.
IV. Return to previous page
Press the SET button to return to previous page if the choice displayed is RETURN.
V. Close the menu screen
Press the SET button to exit the menu system if the choice displayed is END (sub-menu)
or EXIT (main menu only).
Joystick

- 19 -
3.2 ED610 Menu Tree