EVERSPRING AD126 User manual

1
AD126 LAMP MODULE
This plug-in Lamp Module is a transceiver which is a Z-Wave
TM
enabled device
and is fully compatible with any Z-Wave
TM
enabled network. Z-Wave
TM
enabled
devices displaying the Z-Wave
TM
logo can also be used with it regardless of the
manufacturer, and ours can also be used in other manufacturer’s Z-Wave
TM
enabled networks. Inclusion of the Lamp module on other manufacturer’s
Wireless Controller menu allows remote On/Off control and dimming of lamps
connected. Each module is designed to act as a repeater. Repeaters will
re-transmit the RF signal to ensure that the signal is received by its intended
destination by routing the signal around obstacles and radio dead spots.
Adding to Z-Wave
TM
Network
In the front casing, there is an On/Off/Dim knob which is used to carry out inclusion,
exclusion or association. Put a Z-Wave
TM
Wireless Controller into
inclusion/exclusion mode, and then press the knob on the Module to complete the
inclusion/exclusion process. Refer to the table below:
Function Description
Inclusion 1. Put the Z-Wave Controller into inclusion mode.
2. Press the On/Off/Dim knob once to enter inclusion mode.
Exclusion 1. Put the Z-Wave Controller into exclusion mode.
2. Press the On/Off/Dim knob once to enter exclusion mode.
3. Node ID has been excluded.
Association 1. Operate the Z-Wave Controller to start association process.
2. Press the On/Off/Dim knob once to execute association.
Installation
1. Plug this Lamp module into a wall outlet near the lamp to be controlled.
2. Plug the lamp into the Lamp Module. There are two outlets at different sides of
AD126. The lamp plugged into the controllable outlet can be controlled by the
On/Off/Dim knob and remote controller, its maximum load is 300 watts. The
other side acts as a pass-through outlet which is non-controlled by the
On/Off/Dim knob and remote controller.
3. Make sure the total load of both outlets cannot exceed 1500 watts which
means if the load of controllable outlet is changed; the other pass-through will
be altered accordingly. For instance, if the load of controllable outlet is about
300 watts, the other should be 1200 watts. When the load of controllable outlet
consumes as 0 watts, the other will be 1500 watts.
4. Turn the knob or switch on the lamp to the ON position.
5. To manually turn ON the AD126 Lamp Module, press and release the
On/Off/Dim knob. The red indicator LED will turn ON, and the lamp plugged
into the AD126 Lamp Module will also turn ON.
6. To manually turn OFF the AD126 Lamp Module, simply press and release the
On/Off/Dim knob. The red indicator LED will turn OFF and the lamp plugged
into the AD126 Lamp Module will also turn OFF.
7. To manually dim the AD126 Lamp Module, press and hold the On/Off/Dim
knob until the desired lighting level has been reached.
Note: Dimming an inductive load, such as a motor or a transformer, could
impair the dimmer and load attached as well.
Programming
The On/Off/Dim knob allows the user
- Turn on, off or dim the lamp attached
- Include or exclude the module from the Z-Wave
TM
system
- Control other Z-Wave
TM
enabled devices
On /Off / Dim knob
Controllable outlet
Pass-through outlet

2
Advanced Operation
Any Z-Wave
TM
enabled device that can send the following alarm command:
(ALARM_REPORT, Alarm Type == 0x01, Alarm Level == 0x11)
to the AD126 Lamp Module will enable its red indicator LED and the load plugged
into the AD126 Lamp Module to be on and off intermittently for 10 seconds
simultaneously.
Troubleshooting
Symptom
Cause of Failure
Recommendation
The Module not working and
LED off
1. The Module is not plugged into
the electrical outlet properly
2. The Module is out of order
1. Check power
connections
2. Do not disassemble the
Module; send it for repair.
The Module LED illuminating,
but cannot control the
ON/OFF Switch of the lamp
attached
Check if the lamp plugged into the
Module has burned out
Replace a new lamp
The Module LED illuminating,
but the Detector cannot
control the Module
1. Not carry out association
2. Frequency interference
1. Carry out association
2. Wait for a while to re-try
Specification
Operating Voltage 120V/60Hz
Maximum Load 300W, for incandescent lamps only
Minimum Load 25W, for incandescent lamps only
Range Minimum 100 feet line of sight
Frequency Range 908.42 MHz
FCC ID FU5TR003-01
** Specifications are subject to change without notice. A501111257R01 2013/09
Compatible Devices
The Everspring AD126 Lamp module is fully Z-Wave
TM
device compatible.
Homeowners with existing Z-Wave
TM
devices can easily add this device or more
in to complete a safety network firmly. The following Everspring devices are
compatible with AD126 Lamp module.
The following modules (sold separately) can be compatible with this device:
SP103 SM103 ST812 ST814 ST815
PIR Detector Door/Windows Floor Temperature/Humidity Illuminatinon
Detector Detector Detector Detector
IMPORTANT! To ensure better compatibility, only purchase Everspring or other
manufactures’ Z-Wave
TM
Enabled devices.
Mobile of end product
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.

3
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging your health
and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to
take back your old appliance for disposal at least for free of charge.