evertz 7880IP-ASI-IP User manual

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page i
TABLE OF CONTENTS
1. OVERVIEW...................................................................................................................................1
2. INSTALLATION.............................................................................................................................3
2.1. REAR PLATE DESCRIPTION..............................................................................................3
2.1.1. Video Connections ....................................................................................................3
2.1.2. Ethernet Connection..................................................................................................4
2.2. HARDWARE INSTALLATION..............................................................................................5
2.3. CONFIGURING THE BASIC NETWORK SETTINGS...........................................................8
2.4. CONNECTING TO VLPRO...................................................................................................9
3. SPECIFICATIONS.......................................................................................................................11
3.1. TECHNICAL DESCRIPTION..............................................................................................11
3.1.1. Inputs and Outputs..................................................................................................11
3.1.2. Encapsulation Parameters ......................................................................................11
3.1.3. De-Encapsulation Parameters.................................................................................11
3.1.4. Monitored Parameters.............................................................................................11
3.1.5. Physical (number of slots).......................................................................................11
4. CARD CONFIGURATION ...........................................................................................................12
4.1. CONTROL TAB..................................................................................................................12
4.1.1. ASI Port Control Section..........................................................................................12
4.1.2. Output IP Stream 1 & 2 Sections.............................................................................13
4.2. MONITOR TAB...................................................................................................................14
4.2.1. Output IP Stream 1 & 2 Sections.............................................................................15
4.2.2. ASI Input Monitor Section........................................................................................16
4.3. IP TO OUTPUT TAB...........................................................................................................17
4.3.1. ASI Port Control ......................................................................................................17
4.3.2. IP Input Control Section...........................................................................................17
4.3.3. ASI Output Monitor..................................................................................................18
4.3.4. IP Input Monitor.......................................................................................................18
5. TROUBLESHOOTING ................................................................................................................20
5.1. UPDATING VLPRO SERVER JAR FILE............................................................................20

7800/7700 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page ii Revision 1.1
Figures
Figure 1-1: 7880IP-ASI-IP Block Diagram........................................................................................................2
Figure 2-1: 7880IP-ASI-IP Rear Plate...............................................................................................................3
Figure 2-2: 7700 Chassis Rear Panel...............................................................................................................5
Figure 2-3: 7700 Frame Controller....................................................................................................................6
Figure 2-4: COM Port Properties Window........................................................................................................6
Figure 2-5: 7880IP-ASI-IP HyperTerminal Main Menu.....................................................................................7
Figure 2-6: 7880IP-ASI-IP Network Configuration Sub-Menu ..........................................................................8
Figure 2-7: 7880IP-ASI-IP VistaLINK®PRO Hardware Tree Configuration......................................................9
Figure 4-1: InputToIP Control Tab..................................................................................................................12
Figure 4-2: InputToIP Monitor Tab..................................................................................................................15
Figure 4-3: IP to Output Tab...........................................................................................................................17
Figure 5-1: VistaLINK®PRO Server ...............................................................................................................20
Figure 5-2: VistaLINK®PRO – Applying JAR Updates...................................................................................21

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page iii
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 First Release Oct 2009
1.1 Note added to Configuring the Basic Networks Setting section Nov 2011
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof
nor for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning
performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The
only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order
confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no
warranty is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or
order confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If
you encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make
changes in equipment design or specifications.

7800/7700 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page iv Revision 1.1
This page left intentionally blank

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 1
1. OVERVIEW
The 7880IP-ASI-IP is a complete hardware based solution to transform ASI to IP, IP to ASI. It can
also regenerate IP from IP input with different settings and add RTP and FEC. As more providers are
trying to deliver contribution and distribution quality video over IP networks, the 7880IP-ASI-IP is
capable of bridging traditional compressed world (ASI) with standard IP networks.
Controlled by the industry leading VistaLINK® PRO, the 7880IP-ASI-IP offers signal providers the
capability to encapsulate MPEG-2 transport stream payload to a unicast or multicast standardized IP
stream. The 7880IP-ASI-IP is also capable of receiving IP stream and re-create ASI stream. For
contribution application, the 7880IP-ASI-IP offers industry standard FEC support for encapsulation or
de-encapsulation.
The 7880IP-ASI-IP occupies one card slot and can be housed in a 1RU frame which will hold up to 3
modules, a 3RU frame which will hold up to 14 modules.
Applications include:
•ASI to IP conversion
•IP to ASI conversion
•IP-IP translation
•Unicast/Multicast to Unicast/Multicast translation
•UDP or RTP input/output
•FEC ProMPEG CoP3 r2 option to IP streams
Features:
•Fully integrated with the Industry leading Evertz VistaLINK® PRO NMS system
•2 Independent IP Ports, 1 ASI input, 1 ASI Bypass and 1 ASI output
•ASI to IP conversion
•IP to ASI conversion
•IP to IP translation
•FEC encoding and decoding- Pro MPEG forum Code of Practice #3- Release 2<cop3>
•Built-in frame controller for control (separate IP port)

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 2 Revision 1.1
TS processor
IP
encapsulators
CPU
Controller VistaLINK
Control
ASI
Input
10/100 RJ45
ASI
Loop Out
ASI
Output
Card
Edge
Input
Present
Module
Status
FEC
Generator
Output processor
10/100/1000
RJ45
10/100/1000
RJ45
Equalizer
Cable
Driver
TS processor
IP De-
encapsulators
FEC
Receptor
Input processor
IP
Router
Ethernet 1
Mac adr. 1
IP Stack 1
Ethernet 1
Mac adr. 1
IP Stack 1
Figure 1-1: 7880IP-ASI-IP Block Diagram

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 3
2. INSTALLATION
2.1. REAR PLATE DESCRIPTION
The 7880IP-ASI-IP comes standard with a companion +3RU rear plate. Figure 2-1 provides an
illustration of the 7880IP-ASI-IP rear plate. For information on mounting the rear plate and inserting
the module into the frame, see section 3 of the 7700FR manual.
Figure 2-1: 7880IP-ASI-IP Rear Plate
2.1.1. Video Connections
ASI IN: This BNC connector is compatible with DVB/ATSC-ASI standards. The maximum
input bandwidth of each input cannot exceed 270 Mb/s. This ASI Input corresponds
to the Loop Out on the 7880IP-ASI-IP module.
LOOP OUT: This BNC can be used to loop out the ASI input. It is mainly used for troubleshooting
purposes.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 4 Revision 1.1
ASI OUT: This BNC connector output is compatible with DVB/ATSC-ASI standards. This ASI
Outputs corresponds to the IP Inputs on the 7880IP-ASI-IP module.
2.1.2. Ethernet Connection
The 7880IP-ASI-IP Series uses 10Base-T (10 Mbps), 100Base-TX (100 Mbps) or Gigabit (1Gbps)
twisted pair Ethernet cabling systems. When connecting for 10Base-T systems, category 3, 4, or 5
UTP cable as well as EIA/TIA – 568 100ΩSTP cable may be used. When connecting for 100Base-TX
systems, category 5 UTP cable is required. The cable must be “straight-through” with an RJ-45
connector at each end. Establish the network connection by plugging one end of the cable into the RJ-
45 receptacle of the card and the other end into a port of the supporting hub.
The straight-through RJ-45 cable can be purchased or can be constructed using the pin-out
information in Table 2-1. A colour coded wiring table is provided in Table 2-1 for the current RJ-45
standards (AT&T 258A or EIA/TIA 258B colour coding shown). Also refer to the notes following the
table for additional wiring guide information.
Pin
1
Pin # Signal EIA/TIA 568A
AT&T 258A or
EIA/TIA 568B
10BaseT
or 100BaseT
1
Transmit +
White/Green
White/Orange
X
2
Transmit –
Green/White or White
Orange/White or Orange
X
3
Receive +
White/Orange
White/Green
X
4
N/A
Blue/White or Blue
Blue/White or Blue
Not used (required)
5
N/A
White/Blue
White/Blue
Not used (required)
6
Receive –
Orange/White or Orange
Green/White or Green
X
7
N/A
White/Brown
White/Brown
Not used (required)
8
N/A
Brown/White or Brown
Brown/White or Brown
Not used (required)
Table 2-1: Standard RJ-45 Wiring Colour Codes
Note the following cabling information for this wiring guide:
•Only two pairs of wires are used in the 8-pin RJ-45 connector to carry Ethernet signals.
•Even though pins 4, 5, 7 and 8 are not used, it is mandatory that they be present in the cable.
•10BaseT and 100BaseT use the same pins (a crossover cable made for one will also work with
the other).
•Pairs may be solid colours and not have a stripe.
•Category 5 cable must use Category 5 rated connectors.
The maximum cable run between the router and the supporting hub is 300 ft (90 m). The maximum
combined cable run between any two end points (i.e. router and PC/laptop via network hub) is 675 feet
(205 m).
Devices on the Ethernet network continually monitor the receive data path for activity as a means of
checking that the link is working correctly. When the network is idle, the devices also send a link test
signal to one another to verify link integrity. The rear panel is fitted with two LEDs to monitor the
Ethernet connection.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 5
1000: This Amber LED is ON when a 100Base-TX link is last detected. The LED is OFF when a
10Base-T link is last detected (the LINK LED is ON). Upon power-up the LED is OFF as
the last detected rate is not known and therefore defaults to the 10Base-T state until rate
detection is completed.
LN/ACT: This dual purpose Green LED indicates that the card has established a valid linkage to its
hub, and whether the module is sending or receiving data. This LED will be ON when the
module has established a good link to its supporting hub. This gives you a good
indication that the segment is wired correctly. The LED will BLINK when the module is
sending or receiving data. The LED will be OFF if there is no valid connection.
2.2. HARDWARE INSTALLATION
To successfully install the 7880IP-ASI-IP, you will require the following items:
1. Unused IP address on the network or a DHCP server
2. Evertz serial cable
3. VLPro Server IP address
Before handling the card it is important to minimize the potential effects of static electricity. It is
therefore recommended that an ESD strap be worn.
Locate on a 7700 chassis two adjacent vacant slots. Unpack the card and separate the rear card from
the main card. Locate on the rear of the rack the two slots and remove the blanking panels. Insert the
rear card into the back of the chassis and secure using the four screws provided.
Figure 2-2: 7700 Chassis Rear Panel
Before inserting the front card, connect the serial cable to the board using the serial cable provided.
Now insert the card into the corresponding front slots ensuring the card lines up with the slot runners
on the bottom and the top of the chassis. Push the card firmly into the slot ensuring that when it mates
with the rear plate that is has been securely pushed into a seated position. This can be confirmed when
the connectivity lights for the Ethernet port are illuminated. Do not connect any cables to the rear card
until the initial configuration has been completed (failure to do this could cause unwanted network
issues).

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 6 Revision 1.1
Figure 2-3: 7700 Frame Controller
Figure 2-4: COM Port Properties Window
Connect the 9-pin d-type end of the serial cable to the serial port of your computer. Open a Terminal
session and configure the port for the following configuration:
Bits per second
115200
Data Bits
8
Parity
None
Stop Bits
2
Flow Control
None

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 7
Click OK to apply these settings and press the enter button on your keyboard. The card Main Menu
should appear as shown in Figure 2-5:
Figure 2-5: 7880IP-ASI-IP HyperTerminal Main Menu
(1) Control Network Configuration
This sub-menu enables the user to configure the control network settings. The Configuring this sub-
menu allows the user to access the card through the VLPro Client interface.
(2) Data Network Configuration
This sub-menu enables the user to configure the data port network settings. This setup can
alternatively be completed from VLPro once the control network settings have been established.
(3) SNMP Configuration
This sub-menu enables the user to configure the Simple Network Management Protocol settings. In
this menu you can set or remove the SNMP trap IP address and the SNMP Read and Set community
strings.
(4) Debug Interface
This menu is for Evertz personnel only. You may be requested to access and execute options within
this menu when seeking technical support from Evertz. Guidance will be given should this be required.
Before is it possible to configure the card via VLPro it is first necessary to configure the initial basic
network settings via the serial cable. Refer to section 2.3.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 8 Revision 1.1
2.3. CONFIGURING THE BASIC NETWORK SETTINGS
From the terminal session window select option (1) Control Network Configuration, the Control Network
Configuration menu will be displayed as shown in Figure 2-6.
1. Select option (1) Set IP Address and configure the card IP address, ensuring that the IP
address is not already in use on the network.
2. Select option (2) Set Netmask and configure the correct subnet mask for your network.
3. If required also configure option (3) Set Gateway.
4. Exit the Network Configuration menu using (s) Save and Exit, NOT (x) Exit.
Figure 2-6: 7880IP-ASI-IP Network Configuration Sub-Menu
You have now completed the necessary minimum configuration and can connect the cables to the rear
card when ready.

Note: It is recommended that the Data Port traffic is on a subnet/VLAN that is
isolated from the Control network.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 9
2.4. CONNECTING TO VLPRO
This chapter assumes that the VLPro server and VLPro client are already configured for your network
and you have basic knowledge of the VLPro interface. It also assumes that the user or network
administrator has already added the appropriate jar file to the server, and both the client and server
applications have been restarted. Please refer to the VistaLINK®manual for instruction on how to load
a jar file. If you are the network administrator refer to section 5.1 for information on updating the VLPro
Server Jar File.
Open VLPro and click on the refresh tree icon. Expand the hardware tree by clicking on the “+” button.
Your card should appear as a newly listed device with the IP address used to configure the card in
Step 1 above. It may take up to a minute to appear while the card and switch negotiate network
settings (this can be verified directly on the switch if necessary). Please note that the 7880IP-ASI-IP
will identify two items under the IP address in the navigation tree: IpToAsi and InputToIp. The user will
be required to individually select each item to configure the appropriate function.

It is important to note that the 7880IP-ASI-IP is designed to perform 1 translation at
a time. ASI-IP, IP-ASI and IP-IP can all be preformed but not simultaneously. Proper
settings on the card must be placed to ensure 1 translation is occurring at a time
As shown in Figure 2-7, the card will list two inputs (numbered one and two).
Figure 2-7: 7880IP-ASI-IP VistaLINK®PRO Hardware Tree Configuration

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 10 Revision 1.1

Note: If after a couple of minutes the card has still not appeared, try selecting
Add Agent from the Tree> Add/Update Agent menu. Enter the IP address used
in the configuration stage earlier and select OK. The card should now be listed
and will remain greyed out for a moment while VLPro finds the card and
confirms its configuration.
Please consult your network administrator if you continue to have problems connecting the card with
VLPro, alternatively contact Evertz Microsystems Ltd. or your authorized reseller for technical support.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 11
3. SPECIFICATIONS
3.1. TECHNICAL DESCRIPTION
3.1.1. Inputs and Outputs
•1xASI input per DVB TR 101 891 270Mb/s
•1xASI output per DVB TR 101 891 270Mb/s
•Min ASI TS input bitrate 100kb/s
•Max ASI TS input bitrate 200Mb/s
•2xRJ45 10/100/1000 GigE I/O for MPEG over IP
•1xRJ45 10/100 control port
3.1.2. Encapsulation Parameters
•IP encapsulation for each ASI input:
•MAC 802.3>IPV4>RTP>UDP>MPEG (RTP can be turned on and off)
•Select 1 to 7 MPEG packets per IP frame
•Optional FEC encoding (Pro MPEG forum code of practice #3- release 2<cop3>) with L&D
following the below mentioned range:
L*D ≤100
1 ≤ L ≤ 20
4 ≤ D ≤ 20
•IP address (IP, Subnet mask, Gateway) for the source
•IP address for the destination (Unicast and Multicast)
•Selection of the source port and destination port
•Set Local MAC address of the equipment
3.1.3. De-Encapsulation Parameters
•Join Multicast by providing correct messaging using IGMP V2/V3 (SSM Support)
•Selection of the UDP Ports
3.1.4. Monitored Parameters
•Total Bitrate
•Null Packet Bitrate
•TS_sync_loss
•Continuity count error
•PID List
3.1.5. Physical (number of slots)
350FR: 1
7700FR-C: 1
7800FR: 1

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 12 Revision 1.1
4. CARD CONFIGURATION
Right click the IP address and sub-modules of the 7880IP-ASI-IP to access and configure their
parameters. Select “View Configuration” from one of the modules available (Main, IpToAsi and
InputToIp). The configuration page will open enabling the user to toggle the configuration tabs in order
to configure the parameters of the 7880IP-ASI-IP. Sections 4.1 to 4.3 provide an explanation of the
features and functions of the 7880IP-ASI-IP card.
4.1. CONTROL TAB
The control tab is divided into three sub-sections, which include: ASI Port Control, Output IP Stream
1and Output IP Stream 2.
Figure 4-1: InputToIP Control Tab
4.1.1. ASI Port Control Section
The ASI Port Control allows the user to enable or disable the physical ASI input on the card.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 13
4.1.2. Output IP Stream 1 & 2 Sections
Please note that the controls for Output IP Stream 1 and 2 are identical, therefore for the sake of
simplicity only Output IP Stream 1 will be discussed in this manual.
•Stream Active: This option allows the user to quickly enable or disable the outgoing Ethernet
stream by selecting either Active or Inactive.
•Ethernet Output Port: This field shows which physical data port is being used for streaming
data.
•Input: This field allows the user to select the source of the stream. The user will select either
ASI or IP.
•Sources IP Address: This field enables the user to enter the source IP address. This address
can be the physical IP address of your data port, or any other address that you may want to be
encapsulated within the IP packets.
•Sources UDP Port (0 to 65535): This field enables the user to enter the source port number
for the IP address entered above.
•Destination IP Address: This field enables the user to enter the unicast or a multicast IP
address. Multicast addresses should be in the range of 224.0.0.0 through 239.255.255.255.
•Destination UDP Port (0 to 65535): This field enables the user to enter the destination port
number for the IP address entered above.
•RTP Protocol: Use this drop down box to enable (On) or disable (Off) the use of the RTP. The
use of RTP is recommended as it provides services such as time stamping, sequence
numbering and delivery monitoring, which can be beneficial for real-time delivery systems. Also
this protocol must be enabled if the user wishes to use the FEC (Forward Error Correction)
mode.
•TOS: This field enables the user to enter the ToS (Type of Service) value, if your network does
not support ToS, use zero as default.
•TTL: This field enables the user to enter the TTL (Time to Live) value. Using the multicast IP
protocol, the TTL value indicates the scope or range in which a packet may be forwarded. By
convention:
0 is restricted to the same host
1 is restricted to the same subnet
32 is restricted to the same site
64 is restricted to the same region
128 is restricted to the same continent
255 is unrestricted

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 14 Revision 1.1
•TS Packet Per Frame: This field enables the user to enter the number of MPEG packets to be
encapsulated per IP packet. The range of MPEG packets per IP packet is from 1 to 7. Long-
length packets are undesirable due to the excessive impact from losing each IP packet. Short
packets cause a high overhead so a value chosen will be a compromise between these two
factors.
•TS Packets Size: This field enables the user to select the size of the TS packet. The size
options include Auto, 204 bytes or 188 bytes.
•FEC (Forward Error Correction) Mode: This field enables the user to enter the FEC mode to
be used. It will be either FEC 1D (1 Dimensional) or FEC 2D (2 Dimensional).
•FEC Column: This field enables the user to enter the number of packets per column to be
associated with an FEC packet.
•FEC Row: This field enables the user to enter the number of packets per row to be associated
with an FEC packet.
•FEC Offset (Annex A): Use this drop down menu to enable the use of a non-block aligned FEC
arrangement, which is an alternative method of generating the FEC packets. For more
information on the FEC offset refer to the Pro-MPEG Code of Practice #3 release 2, Annex A.
4.2. MONITOR TAB
The Monitor page displays the status of the Ethernet Data ports and the ASI input ports. The Output
IP Stream Monitor section displays the port’s mode of operation in the Status field and the Total Bit
rate that is being output.
The ASI Input Monitor section displays the status of the ASI inputs. The status will not change unless
a valid ASI feed is detected (you may be required to refresh the status or select auto-refresh to view
the change). Using the auto refresh button can aid troubleshooting of connectivity issues, however, it
will prevent any configuration changes. The ASI monitoring fields can be reset at any time by clicking
on the “Clear ASI 1 Stats” button.
There are no user configurable items on this page. This page is for information purposes only.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Revision 1.1 Page 15
Figure 4-2: InputToIP Monitor Tab
4.2.1. Output IP Stream 1 & 2 Sections
Please note that the field for Output IP Stream 1 and 2 are identical, therefore for the sake of simplicity
only Output IP Stream 1 will be discussed in this manual.
•Stream Type: Depending on the destination IP addresses the Stream Type will be a Multicast or
Unicast
•Sent Ethernet Bandwidth: This field identifies the current bitrate of the Output IP Stream 1.
•Sent IP Packets: This field identifies the current total number of IP Packets sent.
•Sent TS Packets: This field identifies the current total number of TS Packets sent.
•Clear Stream Stats: The network statistic can be reset at any time by selecting the “Clear Stream
Stats” button. To apply the new setting, click the Apply button and the statistics will be reset and
begin counting from zero again.

7700/7800 MultiFrame Manual
7880IP-ASI-IP IP/ASI/IP Converter
Page 16 Revision 1.1
4.2.2. ASI Input Monitor Section
•ASI Input: This field displays the standard of the ASI signal.
•ASI Port Status: This field displays whether the status of the ASI signal is Active or Inactive.
•ASI TS Bitrate: This field displays the overall bit rate of the incoming ASI signal.
•ASI Useful Bitrate: This field displays the payload total bit rate.
•ASI Null Packet Bitrate: This field displays the null packets bit rate
•ASI Sync Lost: This counter increments every time the sync bite is not detected. The actual
synchronization of the TS depends on the number of correct sync bytes necessary for the device to
synchronize; two or more consecutive corrupted sync bytes indicate sync loss.
•ASI Continuity Count Errors: A continuity counter error is indicated if the value of the continuity
counter field within a payload packet is not incremented by one, and the packet is not a valid
duplicate or discontinuity packet.
•ASI Input Packet Size: This field displays the input packet size: MPEG2 TS Packet 188/204 byte
•Clear ASI Stats: The ASI monitoring fields can be reset at any time by selecting the “Clear ASI
Stats” button. To apply the new setting, click the Apply button and the statistics will be reset and
begin counting from zero again.