EVGA 790i - nForce SLI FTW Motherboard User manual

The following quick steps will guide you through testing the absolute bare minimum essentials of your motherboard before installing it into a system chassis.
Visual aids are provided to assist you during the following procedures.
To reduce the risk of fire, electric shock, and injury always follow basic safety precautions. It is recommended that you use electrostatic discharge (ESD)
countermeasures such as an ESD wrist strap or anti-static mat when handling computer components.
After removing the EVGA nForce 790i SLITM FTW DIGITAL PWM from its packaging, place it on to a nonconductive surface. For example: wood, cardboard box,
or an anti-static mat.
EVGA nForce 790i SLITM FTW DIGITAL PWM Visual Guide
Unhook the socket lever and lift up the load plate. Remove the LGA 775 protective cover and carefully install your Intel processor making sure to properly align the notches.
Close the load plate and with light pressure, lower the socket lever back in to its original position.
12
a. b.
a. b.
a.
b.
c. a. b.
a. b.
a. b.
c. d.
a. b.
c. d.
c.
Apply a small, pea-sized drop of thermal paste on to the middle of the processor. Install your processor heatsink and fan.
Install one stick of system memory (DIMM) in to the DIMM slot of your choice.
4
Plug in one keyboard into a USB port or PS/2 port.
3
Make sure your power supply’s power switch is in the OFF position then connect your 24-Pin ATX Power Connector
and 8-Pin CPU Power Connector to the motherboard.
6
On the power supply, flip the power switch to the
ON position. LEDs will now be lit on the motherboard.
Press the onboard Clear CMOS button once then press
the green Power Button to begin powering up the system.
Press the onboard Clear CMOS button
Press the green power button
At this final stage, you should now be greeted with the
POST screen on your monitor.
9
Connect one hard drive disk to either one of the SATA Connectors or to the IDE Connector
depending on the hard disk drive connection type.
SATA Connection
Power Button
IDE Connection
8
a. b.
c. d.
Insert your graphics card into either the PCI-E 2.0 slot or the PCI slot. The type of slot depends on the graphic card
bus type. Connect a monitor to the output connector of the graphics card.
5
Plug in power connectors to both the graphics card and the hard disk drive. Power connector types will vary
depending on the hard disk drive and graphic card’s power requirements.
7

EVGA nForce 790i SLITM FTW DIGITAL PWM Quick Install Guide
Installing the CPU
Thank you for purchasing an EVGA product.
Please remember to register your product at:
http://www.evga.com/register
For the latest drivers and updates for your
product please visit:
http://www.evga.com/support/drivers
To visit and search our knowledge base and
product FAQ please visit:
http://www.evga.com/FAQ
To visit the EVGA community message
boards please visit:
http://www.evga.com/forums
1. Unlock the socket by pressing
the lever sideways, then lift it up
to a 90oangle.
2. Lift the load plate. There is
a protective socket cover on the
load plate to protect the socket
when there is no CPU installed.
3. Remove the protective socket
cover from the load plate.
(Save this protective piece,
as it is needed whenever
transporting or shipping the
motherboard.)
4. Align the notches in the CPU
with the notches on the socket.
5. Lower the CPU straight into
the socket. Close the lid plate
and engage the socket lever.
6. The CPU will need a proper
cooling solution, please refer
to the manual that came with
your heatsink for detailed
instructions.
Installing System
Memory
Installing the
Graphics Card(s)
GPU 1
GPU 2
GPU 3
24 pin ATX power
Floppy
SATA
IDE
IDE Channel
SATA ports
SATA ports Floppy Channel
8 pin 12v power
1. This motherboard has three
PCI Express X16 slots. If
installing a single graphics
card use the PCI-E slot closest
to the CPU socket.
(Three)
PCI Express X16 slots.
Connecting Peripherals
Cables
For more information about these services as well as our
terms and conditions please visit
www.evga.com
Gaming ●Imaging ●3D Video ●Entertainment ●Photos ●Graphics
1. Now connect your peripheral
devices such as hard drives,
floppy drive, and DVD-ROM
drives to the motherboard.
2. Connect power cables to the
motherboard and any other
peripherals in your system.
* Remember to plug in your
PCI-E power cables to your
graphics card(s) if necessary.
3. Connect the front panel
headers and any other headers
that are going to be in use.
1. This motherboard supports up
to four 240-pin DDR3 memory
modules. Having matched pairs
is highly recommended for dual
channel configurations.
2. For dual channel configurations
use DIMM slots 0 and 1, 2 and 3,
or 0 through 3. It is recomended
to use the “Black Slots” if running
in 2 DIMM Mode
* Use matching color slots for
dual channel
Support Premium Services
dvanced RMA
Stepping-Up Your Customer Service
Limited Lifetime Warranty
upon product registration
90
Day Step-Up Program
EVGA ADVANCED GRAPHICS TUNING
EVGA Corp 2900 Saturn Street, Suite B Brea, CA 92821 www.evga.com
*Not all Premium Services apply
to all products.
24/7*
Tech Support
888 . 881. EVGA
714 . 528. 4500
www.evga.com/support
*24/7 North America only
PWRLED PWRSW Blank
HD_LED RESET No
Connect
2
+ -
+ -
1
10
9
Connector
IEEE 1394a Connector
SignalPin
1
2
3
4
5
6
7
8
9
10
TPA+
TPA-
GND
GND
TPB+
TPB-
+12V
+12V
Empty
GND
12
34
56
78
910
Connector
USB 2.0 Header
Connector
SignalPin
1
1 2
3 4
5 6
7 8
9 10
3
5
7
9
5V_DUAL
D-
D+
GND
Empty
5V_DUAL
D-
D+
GND
No Connect
2
4
6
8
10
SignalPin
Connector
Front Audio Connector
SignalPin
1
2
3
4
5
6
7
8
9
10
PORT1_L
AUD_GND
PORT1_R
PRECENCE J
PORT2_R
SENSE1_RETURN
SENSE_SEND
Empty
PORT2_L
SENSE2_RETURN
109
87
65
43
21