Evh 5150 ICONIC Series User manual

6L6 40-WATT
1x12 COMBO
OWNER’S MANUAL | MANUAL DE INSTRUCCIONES
MODE D’EMPLOI | MANUALE UTENTE
BEDIENUNGSHANDBUCH | MANUAL DO PROPRIETÁRIO
オ ー ナ ー ズ・マ ニ ュ ア ル
用户手册 | 用戶手冊

1
ENGLISH
A. INPUT: Plug in an instrument here. Use only a high-qual-
ity shielded instrument cable.
B. CHANNEL ONE/TWO SELECT: Pushbutton selects chan-
nel one (low-medium gain, green LED) or channel two
(high gain, red LED). Footswitch overrides this button
when connected to amplifier.
C. CHANNEL ONE GAIN: Preamp gain control for low-
medium gain on channel one. Higher settings increase
preamp distortion.
D. OVERDRIVE SELECT: Sets gain and resets voicing on
channel one from clean to medium distortion.
E. CHANNEL TWO GAIN: Preamp gain control for high
gain on channel two. Higher settings increase preamp
distortion.
F. BURN SELECT: Sets gain and resets voicing in channel
two from high gain to heavier and thicker distortion.
G. NOISE GATE: Reduces noise and tightens attack on chan-
nel two only.
H. LOW/MID/HIGH EQ: Shared passive low-, middle- and
high-frequency tone controls.
I. CHANNEL ONE/CHANNEL TWO VOLUME: Post-preamp
volume controls for each channel. Note: For cleaner
sound from channel one, set this volume control higher
and keep channel one gain control (C) lower.
J. BOOST VOLUME: Footswitchable master volume boost.
Set channel volumes first (I), then use this post-effects
loop control to set solo volume. Footswitch boosts input
gain even when this control is turned fully counterclock-
wise. Note that BOOST VOLUME is only activated using the
included footswitch.
K. REVERB: Adjusts reverb level for both channels (post
effects loop).
L. RESONANCE: Adjusts power amp low-frequency
response by selectively adjusting damping factor.
M. PRESENCE: Adjusts ultra-high frequency tone control for
both channels by selectively adjusting damping factor.
TOP PANELTOP PANEL
EVH® 5150 ICONIC® 6L6 40-WATT 1x12 COMBOEVH® 5150 ICONIC® 6L6 40-WATT 1x12 COMBO
The  Iconic tube amplifier series is designed to capture
many of Edward Van Halen’s iconic guitar tones in a single
amplifier. These simple and easy-to-use two-channel tube
amplifiers accomplish many tonal variations from the EVH
III® series, as well as adding some heavier classic ®
flavors using the overdrive and burn tone switches on chan-
nels one and two respectively. Many modern gig-friendly
features have also been added, including a built-in noise
gate on channel two, front-panel resonance and presence
controls, a quarter-power switch, a footswitchable solo
boost, and an analog-speaker-emulated XLR output for con-
necting directly to external sound reinforcement and record-
ing equipment.

2
N. POWER INPUT: Connect included power cord to amplifier
here, in accordance with the voltage and frequency ratings list-
ed on rear panel of amplifier. Power input’s integral fuse holder
houses a spare fuse. Replace only with a fuse of the same cur-
rent and voltage rating as printed on the back of the amplifier.
O. POWER: Turns amplifier on and off. After turning this switch
ON, wait  seconds for tubes to warm up, then turn STANDBY
switch (P) to ON to take amp out of STANDBY mode. When
turning amplifier off, place amp in STANDBY mode by turning
STANDBY switch OFF for  seconds before turning POWER
switch OFF.
P. STANDBY: Place this switch in OFF position to put ampli-
fier in STANDBY mode. This should be done when taking
a break from playing or before turning amplifier off. Using
STANDBY mode prolongs tube life.
Q. POWER LEVEL SWITCH: Selects full (W) or / (W) power.
R. POWER AMP MUTE SWITCH: Mutes power amplifier when
engaged, enabling speaker-emulated XLR output for quiet
recording. When mute is engaged, amplifier can be operat-
ed with no speaker connected; however, note that a speaker
should be connected when power amp mute is not in use.
S. SPEAKER EMULATED XLR: For connecting amplifier
directly to sound reinforcement or recording equipment.
Speaker emulator circuit changes amp’s tone to match
speaker’s contribution to overall amp tone. Feature is
designed to sound like the  Iconic X speaker cabi-
net, using analog circuitry to avoid latency or lag.
T. XLR GROUND LIFT SWITCH: For alleviating ground loop
hum when connected to sound reinforcement or recording
equipment.
U. PREAMP OUTPUT: For connection to effects return or power
amp input on another amplifier for simultaneous multiple
amp use. Also used to send preamp signal directly to a mixer.
V. EFFECTS LOOP: Connect SEND to external effect input;
connect RETURN to external effect output. Effects RETURN
can also be used as an input for an auxiliary preamp bypass-
ing this amplifier’s preamp, while still allowing use of foot-
switchable BOOST VOLUME (J), REVERB (K), RESONANCE (L)
and PRESENCE (M) controls and POWER LEVEL SWITCH (O).
W. FOOTSWITCH: Connect included footswitch here (see
illustration at right). Footswitch enables easy selection
between channels  and  and activates boost system.
Footswitch boost includes a fixed-gain input boost and
the BOOST VOLUME control (J) for increased volume
when soloing. When connected, footswitch disables
front-panel CHANNEL ONE/TWO SELECT pushbutton (B).
X. LOAD IMPEDANCE: Selects amp output impedance (, 
or  ohms) to match speaker load. NOTE: If using the recom-
mended 5150 Iconic 4X12 speaker enclosure, set switch to “16Ω.”
Y. SPEAKER OUTPUTS: For connection to speaker cabinet(s).
Either jack can be used when using only one speaker cabi-
net. Use only high-quality unshielded speaker cables.
NOTE: A speaker must always be plugged into one of the
speaker jacks when the amplifier is on and POWER AMP
MUTE SWITCH (S) is disengaged, or damage may occur. Turn
amplifier off or put it in STANDBY mode when changing
speaker connections or impedance settings
ENGLISH
SPECIFICATIONSSPECIFICATIONS
TYPE PR 6047
POWER REQUIREMENT 250 watts
OUTPUT 10 to 40 watts RMS into 4, 8 or 16 ohms
INPUT IMPEDANCE 240KΩ
OUTPUT IMPEDANCE 4, 8 or 16 ohms (selectable)
FUSES F4A L 250V (100V and 120V units)
F2A L 250V (220-240V units)
FOOTSWITCH Two-button (included)
TUBES Two 6L6GC power amp tubes
Two ECC83S/12AX7 preamp tubes
DIMENSIONS AND WEIGHT Height: 20” (50.8 cm)
Width: 22.5” (57.2 cm)
Depth: 11.25” (28.6 cm)
Weight: 53 lbs. (24 kg)
Product specifications subject to change without notice.
SPEAKER
OUTPUT 1
SPEAKER
OUTPUT 2
IMPEDANCE
SETTING
16NONE 16
16168
8NONE 8
884
4NONE 4
REAR PANELREAR PANEL

A PRODUCT OF
FENDER MUSICAL INSTRUMENTS CORPORATION
311 CESSNA CIRCLE
CORONA, CALIF. 92880 U.S.A.
AMPLIFICADOR DE AUDIO
IMPORTADO POR: Fender Ventas de México, S. de R.L. de C.V.
Calle Huerta #279, Int. A. Col. El Naranjo. C.P. 22785. Ensenada, Baja California, México.
RFC: FVM-140508-CI0
Servicio al Cliente: 01(800) 7887395, 01(800) 7887396, 01(800) 7889433
EVH®, 5150® and Iconic® are trademarks of Edward Van Halen.
Other trademarks are property of their respective owners.
Copyright © 2021 FMIC. All rights reserved
部件名称
本表格依据 SJ/T 11364 的规定编制。
O： 表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
X： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
注： 含有有害物质的部件由于全球技术发展水平限制而无法实现有害物质的替代。
*产品含有喇叭单元时有效。
箱体
喇叭单元*
电子部分
接线端子
电线
附件
有害物质
产品中有害物质的名称及含量
铅
(Pb)
O
O
X
X
X
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
PN 7719344000 rev. d
PART NUMBERS / REFERENCIAS / RÉFÉRENCE / NÚMERO DAS PEÇAS
NUMERO PARTI / TEILENUMMERN / 部品番号
EVH® 5150® Iconic® Series 6L6EVH® 5150® Iconic® Series 6L6
40-Watt 1x12 Combo Black40-Watt 1x12 Combo Black
2257100010 (120V, 60Hz) NA
2257101010 (110V, 60Hz) TW
2257103010 (240V, 50Hz) AUS
2257104010 (230V, 50Hz) UK
2257105010 (220V, 50Hz) ARG
2257106010 (230V, 50Hz) EUR
2257107010 (100V, 50Hz) JPN
2257109010 (220V, 60Hz) ROK
EVH® 5150® Iconic® Series 6L6EVH® 5150® Iconic® Series 6L6
40-Watt 1x12 Combo Ivory40-Watt 1x12 Combo Ivory
2257100410 (120V, 60Hz) NA
2257101410 (110V, 60Hz) TW
2257103410 (240V, 50Hz) AUS
2257104410 (230V, 50Hz) UK
2257105410 (220V, 50Hz) ARG
2257106410 (230V, 50Hz) EUR
2257107410 (100V, 50Hz) JPN
2257109410 (220V, 60Hz) ROK