Excell SI-130 User manual

User Manual
Weighing Scale
SI-130
© Excell Precision Limited 2016. All rights reserved Worldwide.
The information contained herein is the property of Excell Precision Limited and is supplied
without liability for errors or omissions. No part may be reproduced or used except as
authorized by contract or other written permission. The copyright and the foregoing
restriction on reproduction and use extend to all media in which the information may be
embodied.

02025100 ZSME300000339
1
EXCELL PRECISION CO., LTD.
Table of Contents
Chapter 1 Introduction......................................................................................................................... 2
Preparing To Use the Scale...............................................................................................................2
Componennts................................................................................................................................... 2
Apperence ........................................................................................................................................ 2
Specification.....................................................................................................................................3
Keypad function ............................................................................................................................... 3
Display.............................................................................................................................................. 4
Firmware Version ............................................................................................................................. 4
Error Massages................................................................................................................................. 4
Unit Converion .................................................................................................................................4
Chapter 2 Operation ............................................................................................................................ 5
Tare................................................................................................................................................... 5
Net value / Gross value....................................................................................................................5
Counting Function............................................................................................................................ 5
Auto Power Off, Backlight, Hold Mode ............................................................................................ 6

02025100 ZSME300000339
2
EXCELL PRECISION CO., LTD.
Keys
AC power
Battery
cover
4 Feet
Bubble level
Chapter 1 Introduction
Preparing To Use the Scale
1. Please keep the scale in a cool dry place. Do not store it at high temperature.
2. Avoid objects impacting with the scale. Do not drop loads onto the scale or subject the weigh
pan to any strong shock loads.
3. Remove any weight that might be on the weigh pan before power on the scale.
4. We suggest to warm up the scale for 15~20 minutes before operation to ensure best accuracy.
5. Adjust the four levelling feet (if fitted) to set the scale pan level using the spirit bubble level
located at the front of the scale.
6. All goods weighed should be placed in the centre of the weigh pan for accurate weighing. The
overall dimensions of the goods being weighed should not exceed the dimension of the weigh
pan.
7. Notes for dry battery models
If the scale is not going to be used, please take out the dry batteries to avoid electrolyte leakage.
Do not mix different types of dry battery or mix used dry batteries with new dry batteries.
Please make sure “+” , “- “ poles are placed in the correct direction.
Please don’t place the battery in hot areas or try to dissemble the battery, to avoid electrolyte
leakage.
Please don’t keep the used-up battery in the battery case to avoid breakdown.
Componennts
Stainless steel pan plastic pan + scale AC adapter manual
Apperence

02025100 ZSME300000339
3
EXCELL PRECISION CO., LTD.
Specification
Model
Capacity
Division
Resolution
SI130-2.5
2,500g
0.5g
1/5,000
SI130-5
5,000g
1g
1/5,000
SI130-10
10,000g
2g
1/5,000
SI130-15
15,000g
5g
1/5,000
Operating Temperature：0°C ~ 40°C（32°F ~ 104°F）
Power Source : 4* C (UM-2) 1.5V dry batteries (excluded)
Adapter input: AC 100V ~ 240V output: 12VDC/1A
Keypad function
:
Press this key to power off.
:
This key possesses two functions: Power on and zero function.
When the scale is off, press this key to power on.
When the scale is on and the weigh pan is empty (free of load) and the display is not
showing zero, press this key to zero the scale. The zero indication “” shows on left side of
the display.
Zero range: ±2% of full scale (standard, OMIL & NTEP models); ±4% of full scale (Sri Lanka
models)
:
Press this key to deduct the weight of the container.
This key is not functional when the weight value shown on the display is negative or over the
full scale capacity.
:
Press this key to select desired weight units or piece unit (Pcs). The indications will
indicate the active units
:
Press this key to switch between the “Net value” and the “Gross value”
The gross weight = Tare weight + Net weight (The key is ONLY functional in the Tare mode)

02025100 ZSME300000339
4
EXCELL PRECISION CO., LTD.
TARE
ZERO
g
Pcs
Weight unit
When using counting function,
pcs indication on; otherwise off
Low power
indication
Display
Firmware Version
When power is off, hold key and press key to wait till display shows
and then press key twice to enter .Press key and displays firmware
version and then press key to display maintenance number for 2 secs.
Press key to back to last screen and displays .Press key and display
and then press key to exit self-test mode, the scale will restart automatically.
Error Massages
The EEPROM memory is not working correctly.
Zero is higher than the zero range when power on the scale.
Zero is lower than the zero range when power on the scale.
A/D value is unstable
A/D IC malfunction (cannot read A/D value).
The weight of the object is over 9 divisions of the maximum capacity
The display resolution is greater than internal resolution after calibration.
G value is not within the range 9.772~9.829
Error setting
The weight value is greater than zero range, when re-zero the scale.
The weight value is below zero range, when re-zero the scale.
Unit Converion
kg
1 g = 0.001 kg
g
1 g = 1 g
lb
1 g = 0.002204623 lb
lb,oz
1 g = 0.03527396 oz
oz
1 g = 0.03527396 oz

02025100 ZSME300000339
5
EXCELL PRECISION CO., LTD.
Chapter 2 Operation
Tare
Place the object on the weigh pan
When the weight stable, press
to deduct the weight and tare
indication“” shows on.
Remove the object and press
to clear the tare value and tare
indication “” goes off.
Tare continuously: Press key, when weight is added or deducted on weigh pan.
Tare value = the full capacity (the scale can be tared continuously to the full capacity)
Net value / Gross value
In tare mode, tare indication “” shows on
Press to show the gross value,
and tare indication “” goes off
Press again to show the net value
and tare indication “” shows again.
The key is functional ONLY in tare mode.
Counting Function
Use to enter the counting mode.
Pcs indication “” shows on.
Press to select the counting sample
size (10,20,50,100,200)
Place the samples on the weigh pan,
and then press
After the weight is stable, the display
shows the quantity of the samples.
.


.


.

.






.

g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO
.


g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO
g
Pcs
TARE
ZERO

02025100 ZSME300000339
6
EXCELL PRECISION CO., LTD.
After power off the scale, the scale memorizes the selected sample quantity, The scale will show
the same selected sample quantity, when entering the counting mode next time.
If the sample quantities weighed larger than 65536 pcs, the display shows the error message
“”.
Auto Power Off, Backlight, Hold Mode
In weighing mode, press and
together to enter the setting mode.
Use or to set Auto power off time1
Parameter 0～19 (0: No auto power off, 1～19：
When the scale is idle for 1~19 minutes, the scale
auto power off.)
Press to enter Auto backlight setting 2
Use or to select “on”or “off”
(on:Auto backlight on , off : Auto backlight on)
Press to enter Hold mode setting 3
Use or to select hold mode
(0: Hold function disabled, 1: “Peak hold” mode
2: “Stable hold 1”mode, 3: “Stable hold 2”mode)
Press to complete the setting and
back to weighing mode.
Auto power off time1
When the weight on weigh pan is less than 10d or remains idle for the set time, the scale will
automatically power off.
Auto power off is not functional, when using AC adapter as power source.
Therefore, auto power off is ONLY active, when using dry batteries as power source.
Auto backlight setting2
When the weight is over 10d, the display backlight will be on. After the weight is stable for 10
seconds or when the scale returns to zero, the display backlight switches off.
.


g
Pcs
TARE
ZERO

02025100 ZSME300000339
7
EXCELL PRECISION CO., LTD.
upward key (0~9) comfirm/enter key
downward key (9~0) move the c cursor to left
Hold mode setting 3
= Hold function disabled
= “Peak hold” mode
The scale shows the maximum weight value detected from the continuously
changing weight values. Press any key to exit the hold function.
=“Stable hold 1”mode
After the scale is stable, the display shows the current weight value. Press any key to
exit the hold function.
= “Stable hold 2”mode
After the scale is stable, the display shows the current weight value. Exit the hold
function when unloaded and return to zero.