Exitronix CP-EMW Series User manual

IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
When using electrical equipment, basic safety precautions should always be followed including the following:
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
• Installation and servicing of this equipment should be performed by qualified service personnel only.
• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations, if
applicable.
• Do not mount near gas or electric heaters.
• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering
by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Any modification or use of non-original components will void the warranty and product liability.
• Do not use this equipment for other than intended use.
• Allow battery to charge for 48 hours before first use.
SAVE THESE INSTRUCTIONS!
Technical SupportŶŶWHFKQLFDOVXSSRUW#EDUURQOWJFRP
CP-EMW Series
Installation Instructions
R(9 1ZZZEDUURQOWJFRP

Wall Mount
5HPRYHWKHOHQVFRYHUE\ORRVHQLQJWKH[´VFUHZV$DQG
VHWDVLGH)LJ
5HPRYHWKHKRXVLQJE\ORRVHQLQJWKH[³VFUHZV%DQGVHW
aside.
5HPRYHWKHEDWWHU\E\ORRVHQLQJWKHYHOFURVWUDS)LJ
4a. Wall Mount - Remove the center knockout and any desired knockouts for
PRXQWLQJWRWKH-ER[ORFDWHGLQWKHEDFNSODWHDQGWKHFRUUHVSRQGLQJ
knockouts on the supplied gasket. Apply the gasket to the back of the
EDFNSODWHDVVKRZQ0RXQWWKHEDFNSODWHDVVHPEO\WRWKH-ER[
4b. Wall Mount with conduit - Remove the desired knockouts on the
backplate and the corresponding knockouts on the supplied gasket. Apply
the gasket to the back of the backplate, as shown. Mount the backplate
assembly to the wall using appropriate hardware for the mounting surface.
5HPRYHWKHFRQGXLWDFFHVVSOXJDQGLQVWDOOD´137OLTXLGWLJKWILWWLQJ
QRWSURYLGHG
)RUDGGLWLRQDOPRXQWLQJVXSSRUWUHPRYHDGGLWLRQDONQRFNRXWVDQGXVH
DSSURSULDWHKDUGZDUHIRUPRXQWLQJVXUIDFH)LJ
$OOHOHFWULFDOFRQQHFWLRQVVKRXOGEHPDGHLQVLGHWKH
MXQFWLRQER[Make electrical connections as follows:
120VAC 277VAC
White - Common White - Common
%ODFN9$&  2UDQJH9$&
Green - Ground Green - Ground
Note: Cap unused leads to prevent shorting.
6HFXUHWKHEDWWHU\XVLQJWKHYHOFURVWUDS
6HFXUHWKHKRXVLQJXVLQJWKH[³screws from
before.
6HFXUHWKHOHQVFRYHUXVLQJWKH[´screws
from before.
7RZHDWKHUSURRI\RXUIL[WXUHEHVXUHWRVHDODOOKROHVLQ
WKHKRXVLQJPRXQWLQJFRQGXLWSOXJVHWFZLWKVLOLFRQH
sealant. Apply sealant across the top edge to prevent
water from reaching the back of the housing.
Lens Cover
Housing
Fig. 1 $[
[´
%[
[´
%DWWHU\
Velcro
Strap
Knockout
Conduit Access Plug
)LJ
:KLWH&RPPRQ
%ODFN9
2UDQJH9
Green
*URXQG
Transformer
)LJ
Gasket
%DFNSODWH
%DFNSODWH
CP-EMW Series
Installation Instructions
R(9  ZZZEDUURQOWJFRP

Pole or I-beam Mounting (Option)
Note: The universal bracket is an accessory and needs to
be ordered separately.
1. Follow steps 1-4b under Wall Mount.
5HPRYHWKHNQRFNRXWVLQWKHEDFNSODWHDQGJDVNHW
WKDWDOLJQZLWKWKHXQLYHUVDOEUDFNHW)LJ
6HFXUHWKHXQLYHUVDOEUDFNHWZLWK´VFUHZV
´–´LQOHQJWKQRWSURYLGHG
4. Unit can be installed using steel banding for routing
DURXQGWKHSROHVDQG,EHDP6WDQGDUGEDQGLQJLQ
ZLGWKRUOHVVFDQEHXVHGQRWSURYLGHG
)ROORZVWHSVXQGHUWall Mount.
)LJ
Fig. 4
%DFNSODWH
Gasket
6WHHO%DQG
1RWSURYLGHG
Universal
%UDFNHW
2SWLRQ
POLE OR I-BEAM MOUNTING
POLE OR I-BEAM MOUNTING
Weatherproof Seal
6WHHO%DQG
1RWSURYLGHG
Conduit Access Plug
CP-EMW Series
Installation Instructions
R(9  ZZZEDUURQOWJFRP

Self-Test/Self-Diagnostics (G2)
I M P O R T A N T: Once all emergency lamps have been connected to the unit equipment, apply normal AC power and
FKDUJHIRUKRXUV
Following installation and after AC power has been supplied, charge for 48 hours, then press and hold the test button until
the LED indicator turns orange. This calibrates the unit equipment for the proper load.
Operation
The purpose of this option is to provide Self-testing and Self-diagnostic capabilities to the emergency unit. At
predetermined intervals, the emergency unit will automatically switch into battery mode. Refer to the Self-Test Feature
section below for timing details. The emergency unit will also perform various Self-diagnostic tests to determine if there
are any faults. Visual signaling will alert maintenance personnel to a fault of the emergency unit electronics, battery,
DQGRUEDWWHU\FKDUJHU7KHFLUFXLWU\FRQWLQXRXVO\PRQLWRUVWKHRSHUDWLQJFRQGLWLRQRIWKHHPHUJHQF\XQLWDQGEDWWHU\
FKDUJLQJFLUFXLWEDWWHU\VXSSO\YROWDJH5HIHUWRWKHLED Indicator section below for fault reporting details.
Self-Test Feature
• The emergency unit will automatically switch to battery mode everyPRQWKIRUDSHULRGRIPLQXWHV
• The emergency unit will automatically switch to battery mode everyPRQWKVIRUDSHULRGRIPLQXWHV
LED Indicator
The LED indicator of the emergency unit will display a visual signal indicating the status of the unit. Refer to the table
below for LED indication conditions:
Test Button Features
MANUAL TEST – Pressing the test button will switch the unit into battery mode for a set amount of time. The desired
length of the test is determined by the length of time that the test button is pressed.
3UHVVLQJWKHWHVWEXWWRQRQFHZLOOVZLWFKWKHXQLWLQWREDWWHU\PRGHIRUDSHULRGRIVHFRQGV
• Pressing and holding the test button until the LED indicator turns orange will switch the unit into battery mode for a
SHULRGRIPLQXWHV
3UHVVLQJDQGKROGLQJWKHWHVWEXWWRQXQWLOWKH/('LQGLFDWRUIODVKHVUHGJUHHQZLOOVZLWFKWKHXQLWLQWREDWWHU\PRGH
IRUDSHULRGRIPLQXWHV
Pressing the test button once while the unit is MANUAL TEST mode will cancel the manual test and return the unit to
normal AC power.
5(6(7±3UHVVLQJWKHWHVWEXWWRQWLPHVZLOOUHVHWWKHUHG³81,7$/(57´/(',IPXOWLSOHIDXOWVDUHSUHVHQWLWPD\EH
QHFHVVDU\WRUHSHDWWKLVSURFHGXUHIRUHDFKUHPDLQLQJIDXOWLQGLFDWHGE\WKH³81,7$/(57´/('
Use in accordance with local building codes.
LED Indication
Steady
Pulse
Steady
Pulse
Steady
Pulse
LED Color
LED Color
Green
Green
Red
Red
Orange
Orange
5HG*UHHQ
Unit Condition
Float Charge
Hi-Rate Charge
/RZ%DWW9ROWDJH
Emer Lamp Failure
No AC Power
Charge Failure
0LQXWH7HVW
%DWW'LVFRQQHFWHG
0LQXWH7HVW
Comment
%DWW)XOO\&KDUJHG
%DWW8QGHU+LJK5DWH&KDUJH
5HSODFH%DWWHU\
Check AC Connection
Replace Transformer
0LQ7HVW(YHU\0RQWK
&KHFN%DWW&RQQHFWLRQV
0LQ7HVW(YHU\0RQWKV
Replace Damaged or
Missing Lamps
CP-EMW Series
Installation Instructions
R(9 4ZZZEDUURQOWJFRP