Extech Instruments 433201A User manual

User's Guide
Microprocessor Calibrator/Thermometer
Models 433201A and 433202A
netzerotools.com
netzerotools.com
netzerotools.com
Extech 433201 Multi-Type Calibrate Thermometer Thermocouple Type K-J
Extech 433201-NIST Multi-Type Calibrate Thermometer Thermocouple Type K-J

433201A-EN v1.6 07/13
2
Introduction
Congratulations on your purchase of the Extech 433201A (115V) or 433202A (220V)
Microprocessor Thermocouple Calibrator/Thermometer.
In the ‘Measurement’ mode, a millivolt (mV) signal is accepted from a thermocouple and is
displayed on the 4-digit LCD display. A built-in temperature offset feature can be used to
compensate for variations found in standard thermocouples. By adjusting the offset, measurement
accuracy for a particular thermocouple can be optimized for a particular temperature.
In the ‘Source’ mode, a millivolt signal is output to an external device with the corresponding
temperature (according to standard temperature tables) displayed on the LCD display. Preset
temperature settings (source mode only) according to thermocouple type are stored in five memory
locations for easy recall.
If desired, the meter can be switched to the mV mode where Measurement and Source values
can be displayed in millivolts rather than temperature.
Careful use of this device will provide years of reliable service.
netzerotools.com
netzerotools.com

433201A-EN v1.6 07/13
3
Description
1. LCD display – Temperature values can be displayed in oC/oF or in millivolts. The adjustable
display can be easily moved to the best viewing angle.
2. POWER/MODE button – Press to power meter on/off and to select the desired mode of
operation. With the meter powered on, momentarily press the POWER/MODE button (<2
sec) to toggle between MEASURE and SOURCE mode. In MEASURE mode the meter
displays the temperature or mV value for an attached thermocouple or thermocouple
simulator. In the SOURCE mode, the meter outputs a mV signal.
To power off, press and hold the POWER/MODE button for more than 2 seconds.
3. FINE/COARSE output adjustment buttons – Use the ▼/▲buttons to set the desired
temperature. Press and hold for COARSE adjustment; momentarily press for FINE
adjustment.
4. oC/oF button – Press to select the desired unit of measure
5. TYPE button – Press to select a thermocouple type
6. MEM – In SOURCE MODE, the Memory button provides access to five memory locations
with preset output values depending on which thermocouple type is being used.
Memory
Location
Type
J, K, C, R, S, N
Type T Type E mV
M1 32.0oF
(0.0oC)
32.0oF
(0.0oC)
32.0oF
(0.0oC)
0mV
M2 212.0oF
(100.0oC)
212.0oF
(100.0oC)
212.0oF
(100.0oC)
10.00mV
M3 932.0oF
(500.0oC)
392.0oF
(200.0oC)
482.0oF
(250.0oC)
25.00mV
M4 1382.0oF
(750.0oC)
572.0oF
(300.0oC),
932.0oF
(500.0oC)
40.00mV
M5 1832.0oF
(1000.0oC)
752.0oF
(400.0oC)
1382.0oF
(750.0oC)
50.00mV
7. Output/Input mini connector – Thermocouples, thermocouple wire, and calibration cables are
connected here.
8. AC adaptor/recharger jack
9. Battery compartment – Houses the supplied 9V Nickel Metal Hydride rechargeable battery.
An alkaline battery can also be used.
10. Neck Strap Posts- Attach the neck-strap to the two posts on the front corners of the meter.
netzerotools.com
netzerotools.com

433201A-EN v1.6 07/13
4
Operation
Measurement Mode
1. Open the meter lid and press the POWER/MODE button to turn the meter on. “MEASURE”
will be displayed on the LCD screen. Check the battery if the meter display does not switch
on.
Note: For best accuracy, remove any input connectors before turning the unit ON. The
meter will not perform a correct self calibration if there is an input connected.
2. Select the thermocouple type using the TYPE button. The T/C type selected will be indicated
along the bottom of the display. Each time the TYPE button is pressed the indicator will
advance one type.
3. Select
oC or oF via the oC/oF button.
4. Carefully insert the thermocouple probe into the sub-miniature female connector on the side
panel.
5. Read the temperature on the LCD display.
6. To turn the meter off, press and hold the POWER/MODE button for more than 2 seconds.
Offset Adjustment
Thermocouples produce an output signal that is non-linear. In some instances it may be necessary to
offset the reading to compensate for the non-linearity of the thermocouple.
1. In Measurement Mode, press and hold the ▼/▲buttons together until ”OFS” is displayed on
the LCD.
2. Use the ▼/▲buttons to adjust the offset from -9.0 to 9.0oF (-5.0 to 5.0oC)
3. Press and hold the ▼/▲buttons together for less than 2 seconds to save the offset and
return to Measurement Mode.
netzerotools.com
netzerotools.com

433201A-EN v1.6 07/13
5
Source Mode
1. Open the meter lid and press the POWER/MODE button to turn the meter on. Check the
battery if the meter display does not switch on.
2. Momentarily (<2 sec) press the POWER/MODE button to select the SOURCE mode.
“SOURCE” will be displayed on the LCD screen.
3. Select the thermocouple type of the device to be calibrated using the TYPE button. The T/C
type selected will be indicated along the bottom of the display. Each time the TYPE button is
pressed the indicator will advance one type
4. Select °C or °F via the °C/°F button.
5. Carefully insert the calibration cable into the sub-miniature female connector on the side
panel.
Note: For greater accuracy, especially if there is a difference between the internal temperature of the
calibrator and the device under calibration, use a thermocouple cable rather than the copper cable that is
supplied with the calibrator. The thermocouple cable must match the thermocouple type of the device under
calibration.
6. Connect the other end of the cable to the device to be calibrated.
Note: The SOURCE icon will blink until the output has stabilized.
7. Allow time for the calibrator and the external device to settle to the same temperature. This
may take up to 30 minutes or longer if the devices were stored or carried from a
colder/warmer environment prior to use.
8. Use the ▼/▲FINE/COARSE adjustment buttons or the MEM button to select the desired
output temperature. The output temperature is displayed on the LCD display.
9. To turn the meter off, press and hold the POWER/MODE button for more than 2 seconds.
Displaying in mV units
Press and hold the oF/oCbutton for more than 2 seconds until “mV” appears on the LCD display.
Press and hold the button again for more than 2 seconds to return to temperature units (oF/oC).
Auto Power Off
When the meter is turned on, the auto power off function is enabled. It will automatically shut the
meter off 10 minutes after the last button press. To disable Auto Power Off, press and hold the
TYPE button for 2 seconds until “nAtP” is displayed.
netzerotools.com
netzerotools.com

433201A-EN v1.6 07/13
6
Battery Replacement and Recharging
If the meter is to be used for an extended period of time, use of the AC adaptor is recommended.
For portable operation or quick checks use the rechargeable 9V Nickel Metal Hydride battery or a
9V alkaline battery.
Turning the meter OFF when not in use will prolong battery life.
When the battery icon flashes, replace or recharge the battery. Note that only the supplied 9V
NiCad battery can be recharged.
Replace the battery using the following procedure:
1. Fully open the meter.
2. Insert a coin or flat screwdriver into the slot at the back of the meter.
3. Pop the battery compartment cover and then carefully remove it in the direction of the arrow.
4. Replace the battery and snap the cover back in place.
Recharge the supplied 9V Nickel Metal Hydride battery using the following procedure:
1. Turn the meter off.
2. Ensure that the rechargeable battery is installed.
3. Plug the charger/adaptor into the meter.
4. Plug the charge/adaptor into an AC outlet source.
5. Charge the battery for 24 to 48 hours before its first use. An overnight charge will enable
continuous use for approximately 45 minutes. A full charge will provide one hour of
continuous use.
netzerotools.com
netzerotools.com

433201A-EN v1.6 07/13
7
Specifications
Calibration & Measurement Ranges Resolution Accuracy
Type J -58 to 1830OF (-50 to 1000OC) 0.1° to 999.9°
1° above 999.9°
± (0.15% of reading
+ 1.8°F or 1°C)
Type K -58 to 2498OF (-50 to 1370OC)
Type T -184 to 752OF (-120 to 400OC)
Type E -58 to 1382OF (-50 to 750OC)
Type C 32 to 3272OF (0 to 1800OC) 1°
Type R 32 to 3182OF (0 to 1750OC)
Type S 32 to 3182OF (0 to 1750OC)
Type N -58 to 2372OF (-50 to 1300OC)
Voltage -5.00mV to +55.00mV 0.01mV ±2digits
General Specifications
Cold junction compensation 0.02°F per °F (0.03°C per °C)
Input impedance 10M
Maximum voltage applied between any
terminal and earth ground or between
any two terminals
60mV
Storage temperature: -22°F to 176°F (-30°C to +80°C)
Operating temperature: 23°F to 158°F (-5°C to +70°C)
Relative humidity: 0-85%
Approvals CE
Thermocouple Standard and Scale NIST 175, ITS-90
Sampling time Two (2) readings per second
Display 4-digit (0 to 9999) LCD display with
thermocouple type status indication
Power 9V alkaline battery, 9V Nickel Metal Hydride
rechargeable battery, or AC adaptor/charger
Supplied accessories Thermocouple calibration cable (white)
terminated with sub-miniature connectors, K-
type Thermocouple cable (yellow) terminated
with sub-miniature connectors, 9V Nickel Metal
Hydride rechargeable battery, neck-strap, AC
adaptor/charger, carrying case.
Dimensions 4.7 x 3.8 x 1.8” (118 x 96 x 45mm)
Weight 15 oz. (426g)
netzerotools.com
netzerotools.com

433201A-EN v1.6 07/13
8
Warranty
FLIRSystems,Inc.warrantsthisExtechInstrumentsbranddevicetobefreeofdefectsinpartsandworkmanshipforoneyear
fromdateofshipment(asixmonthlimitedwarrantyappliestosensorsandcables).Ifitshouldbecomenecessarytoreturnthe
instrumentforserviceduringorbeyondthewarrantyperiod,contacttheCustomerServiceDepartmentforauthorization.Visit
thewebsiteforcontactinformation.AReturnAuthorization(RA)numbermustbeissuedbeforeanyproductisreturned.The
senderisresponsibleforshippingcharges,freight,insuranceandproperpackagingtopreventdamageintransit.Thiswarranty
doesnotapplytodefectsresultingfromactionoftheusersuchasmisuse,improperwiring,operationoutsideofspecification,
impropermaintenanceorrepair,orunauthorizedmodification.FLIRSystems,Inc.specificallydisclaimsanyimpliedwarranties
ormerchantabilityorfitnessforaspecificpurposeandwillnotbeliableforanydirect,indirect,incidentalorconsequential
damages.FLIR’stotalliabilityislimitedtorepairorreplacementoftheproduct.Thewarrantysetforthaboveisinclusiveandno
otherwarranty,whetherwrittenororal,isexpressedorimplied.
Calibration,Repair,andCustomerCareServices
FLIRSystems,Inc.offersrepairandcalibrationservicesfortheExtechInstrumentsproductswe
sell.NISTcertificationformostproductsisalsoprovided.CalltheCustomerServiceDepartmentfor
informationoncalibrationservicesavailableforthisproduct.Annualcalibrationsshouldbe
performedtoverifymeterperformanceandaccuracy.Technicalsupportandgeneralcustomer
serviceisalsoprovided,refertothecontactinformationprovidedbelow.
netzerotools.com
netzerotools.com